KStrong AFA930001 Manuel de l'opérateur
THESE INSTRUCTIONS APPLY TO THE FOLLOWING MODEL:
EDGE SINGLE POINT ANCHOR
USER INSTRUCTION MANUAL
AFA930001
EN 795:2012 Type A
01
Please read and understand the manufacturer's instructions for each component or part of the complete system. Manufacturer's instructions
must be followed for proper use, care, and maintenance of this product. These instructions must be retained and be kept available for the user's
reference at all times. Alterations or misuse of this product, or failure to follow instructions, may result in serious injury or death.
Note: The user is advised to keep this user instructions document for the life of the product.
1. INTRODUCTION: The Edge Single point anchor is classed as a Personnel Protective Equipment (PPE) by the European PPE
Regulation (EU)2016/425 and has been shown to comply with this Regulation through the Harmonized European Standard EN
795:2012 type A.
This Anchor is designed to minimize the risk of/provide protection against the danger of falling from heights. However, always remember
that no item of PPE can provide full protection and care must always be taken while carrying out the risk related activity.
2. PERFORMANCE AND LIMITATIONS OF USE:
The Anchor has been tested in accordance with EN 795:2012 type A and has achieved the following performance levels-
EN 795:2012 Type A test
General Requirements
for Anchor devices
(Clause 4.2)
Static Strength
(Clause 4.4.1.3)
Dynamic Strength &
Integrity Test
(Clause 4.4.1.2)
Corrosion Resistance
(Clause 4.7)
(PASS)
No sharp edges (PASS).
Sustained a force of 12 kN for 3 minutes (PASS).
When tested with rigid steel mass of 100 kg, the test mass held after test with the
device remaining stable throughout. (PASS)
Anchor Holds an increased load of 300kg for 3 min following dynamic test.
No corrosion evident after 48 hours of salt spray testing. (PASS)
Result/Comment
4. INSTRUCTIONS FOR USAGE :
Single Point Anchor is to be used for anchorage in a fall arrest system.
This anchor can be fixed to walls, ceilings, roof tops or steel structures present
in the working environment.
For fixing to steel structures, drill one hole of dia 12.5mm in the steel
structure (pass through) and bolt the anchor on to it by using one M 12
steel nut bolts. Ensure that the nut & bolt is tightened enough & not loose.
For fixing to walls, ceiling and roof tops, fix only on ones made up of
concrete and known to have compression strength of at least 3000 PSI.
Use one M12 chemical fastener to be fixed in the drill made in to the
concrete structure as per specification stated by the chemical fastener
manufacture.
The Anchor can be fixed so that the load impact is in any of the directions
shown in the adjacent figure:-
Ÿ
Ÿ
3. INSPECTION:
inspection, doubts are raised about the safety of the system or a component, these should be replaced either by the manufacturer or a
competent person.
Visually inspect the system before each use to enusre that it is in a serviceable condition and is operating correctly. If during
02
5. LIMITATIONS
Ÿ The Anchor should be the personal property of its user.
It should not be used in highly acid or basic environment.
The anchor has been tested to EN 795:2012 type A and is appropriate
only for single person use with an energy absorber as per EN 355:2002.
Ensure that the structure on to which the anchor is fitted is strong
enough to withstand a load of 12kN.
Ensure that the Anchor is installed directly above the user's head
6. COMPATIBILITY: To optimise protection, in some instance it may be
necessary to use the with suitable PPE such as: boots/gloves/helmet
and ear protection. In this case, before carrying out the risk-related activity,
consult your supplier to ensure that all your protective products are
compatible and suitable for your application.
7. REPAIR: If the product becomes damaged, it will NOT provide the optimum
level of protection, and therefore should be immediately removed from
service. It needs to be inspected to see if it is replaced or repaired. Never use
the damaged product. Repair is only permitted by the manufacturer or a
nominated repair centre or individual approved by the manufacturer.
8. CLEANING: In case of minor soiling, wipe the anchor with cotton cloth or a
0 0
soft brush. Do not use any abrasive material. For intensive cleaning wash the anchor in water at a temperature between 30 C to 60 C by using
0
a neutral detergent (pH+7). The washing temperature should not exceed 60 C. Do not use acid or basic detergents.
9. STORAGE AND TRANSPORT: When not in use, store the anchor away from heavily acidic or basic environment. Never place heavy items on
top of it. Also ensure that it is stored away from chemically hazardous environment preferebly storage should be in dry environment.
10. WITHDRAWAL FROM USE: If the system has been used to arrest a fall, it should be removed from service and returned to the manufacturer
or a competent repair centre for servicing and re test.
Ÿ
Ÿ
Ÿ
Ÿ
anchor
The Anchor is marked with :
(i) The CE mark showing that the product meets the
requirements of the PPE Regulation (EU)2016/425
(ii) Identification of the manufacturer
(iii) Type or product code
(iv) Product description
(v) UID
MARKING
Read the user
instructions
carefully before
each use.
MAX
1
ANCHOR :
UID: XXXXXXXXXXXX
MM/YY
MBS: 23kN
EN 795:2012 TYPE A
AFA930001
LIFESPAN:
intense use, contact with chemical substances, specially aggressive environments, extreme temperature exposure, UV exposure, abrasions, cuts,
violent impacts, bad use or maintenance.
DISCLAIMER:
The estimated product Lifespan is 10 years from the date of manufacture. The following factors can reduce the Lifespan of the product:
Prior to use, the end user must read and understand the manufacturer's instructions supplied with this product at the time of
shipment and seek training from their employer's trained personnel on the proper usage of the product. Manufacturer is not liable or responsible for
any loss, damage or injury caused or incurred by any person on grounds of improper usage or installation of this product.
Periodic examination
next due date
Product
Model & type/Identification
Trade Name
Address
Identification number
Manufacturer
Tel, email into use
Year of manufacture
Purchase Date
Date first put into use
Other relevant information (eg. document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Date
Name and signature
of competent person
Reason for entry
(periodic examination
or repair)
Defects noted, repairs
relevant information
carried out and other
EQUIPMENT RECORD
AKS- -110121-v2AFA930001
Certification Body:
SATRA Technology Europe Ltd, Bracetown Business Park, Clonee, Dublin D15 YN2P Ireland (Notified Body 2777)
Ongoing Assessment Body:
SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland (Notified Body 0598)
For EU Declaration, please visit https://kstrong.com/asia/eu-declaration-form/
www.kstrong.com
USA South America ASIA
KStrong Inc.
150 N. Radnor Chester Road Suite F200
Radnor, Pennsylvania 19087 United States
Contact number : 1-833-KSTRONG
Table des matières
Autres manuels KStrong Équipements de sécurité
KStrong
KStrong AFX201042 Manuel de l'opérateur
KStrong
KStrong AFS570020R Manuel de l'opérateur
KStrong
KStrong AFL405101 Manuel de l'opérateur
KStrong
KStrong Kapture Element Hotworx Manuel de l'opérateur
KStrong
KStrong AFA930501 Manuel de l'opérateur
KStrong
KStrong UFA40110 Manuel de l'opérateur
KStrong
KStrong AFX202002 Manuel de l'opérateur
KStrong
KStrong AFS551002 Manuel de l'opérateur
KStrong
KStrong AFA945012R Manuel de l'opérateur
KStrong
KStrong AFT7500 Manuel de l'opérateur
KStrong
KStrong USCLC Series Manuel utilisateur
KStrong
KStrong UFA20504 Manuel de l'opérateur
KStrong
KStrong AFA940014 Manuel de l'opérateur
KStrong
KStrong WRANGLER AFA940010 Manuel de l'opérateur
KStrong
KStrong AFX201001 Manuel de l'opérateur
KStrong
KStrong IRSQ SEIZE'M RESCUE KIT Manuel de l'opérateur
KStrong
KStrong AFA930101 Manuel de l'opérateur
KStrong
KStrong KAPTURE ELITE LV2 Manuel de l'opérateur
KStrong
KStrong AFA930050 Manuel de l'opérateur
KStrong
KStrong Evac R+ Manuel utilisateur
Manuels Équipements de sécurité populaires d'autres marques
Innova
Innova Xtirpa Mode d’emploi
bolle SAFETY
bolle SAFETY B810 Manuel utilisateur
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Manuel utilisateur
Hiltron security
Hiltron security POWER8E Mode d’emploi
Hatco
Hatco B-950P Manuel utilisateur
Sitec
Sitec TX MATIC Manuel utilisateur
