Kramer DIP-31M Manuel utilisateur
DIP-31M Quick Start
P/N:
2900- 301076QS
Rev:
2
Scan for full manual
DIP-31M Quick Start Guide
This guide helps you install and use your DIP-31M for the first time.
Go to www.kramerav.com/downloads/DIP-31M to download the latest user manual and check if firmware
upgrades are available.
Step 1: Check what’s in the box
DIP-31M Automatic Video Switcher
1 Set of rack ears
1 Quick start guide
1 Power supply (12V DC)
4 Rubber feet
Step 2: Get to know your DIP-31M
#
Feature
Function
1
HDMI IN 1
SELECT Button
Press to select the HDMI IN 1 input. When HDMI IN 1 is selected, the button lights
and indicates the selected audio (see Step 5):
Red –External audio from the analog Audio IN is selected
Green –Embedded audio from HDMI IN 1 is selected
2
HDMI 1 Connector
Connects to the first HDMI source
3
HDMI IN 2
SELECT Button
Press to select the HDMI IN 2 input. When HDMI IN 2 is selected, the button lights
and indicates the selected audio (see Step 5):
Red –External audio from the analog Audio IN is selected
Green –Embedded audio from HDMI IN 2 is selected
4
HDMI 2 Connector
Connects to the second HDMI source
5
PC IN
SELECT Button
Press to select the VGA input. When PC IN is selected, the button lights and indicates
the selected audio (see Step 5):
Red –External audio from the analog Audio IN is selected
Green –No audio is selected
6
PC Graphics
15-pin HD
Connector
Connects to the VGA source, (for example, a laptop)
7
AUDIO IN 3.5mm Mini Jack
Connects to the unbalanced, stereo audio source, (for example, the audio output of
the laptop)
8
STEP-IN Button
Press to take control of the input that this device is connected to on a compatible
switcher
9
ON LED
Lights green when the device is powered on
#
Feature
Function
10
AUDIO OUT 3.5mm Mini Jack
Connect to the unbalanced, stereo audio acceptor, (for example, active speakers)
11
ETHERNET RJ-45 Connector
Connect to the LAN, (Ethernet traffic or PC controller)
12
RS-232 CONTROL 3-pin Terminal
Block
Connect to a serial controller or PC
13
RS-232 DATA 3-pin Terminal Block
Connect to a serial data source or acceptor
14
PC/HDMI Remote Toggle Switch
Terminal Block
Connect to a remote switch to toggle between the HDMI and VGA inputs. Each
press cycles through the priority inputs HDMI IN 1 HDMI IN 2 PC IN or a
different priority cycle specified on the Video & Audio Settings Web page
15
Remote Contact-closure 4-pin
Terminal Block
Connect to remote momentary switches to control step-in and audio volume
16
FACTORY RESET Button
Short press to reboot, long press to reset the device to factory default parameters
17
SETUP 4-way DIP-switch
Switches for setting the device behavior (see Step 5)
18
PROG Mini USB Connector
Connect to a PC to perform a firmware upgrade
19
HDMI OUT Connector
Connect to a compatible HDMI display
20
12V DC Connector
Connect to the supplied power adapter
The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.
Step 3: Install the DIP-31M
Install DIP-31M using one of the following methods:
•Attach the rubber feet and place the unit on a flat surface.
•Fasten a bracket (included) on each side of the unit and attach it to a flat surface.
For more information go to www.kramerav.com/downloads/DIP-31M.
•Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/product/DIP-31M).
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your DIP-31M. For best results, we recommend that you
always use Kramer high-performance cables to connect AV equipment to the DIP-31M.
Step 5: Set the DIP-switches
Video Switching Selection
DIP-switch 1
DIP-switch 2
Video Input Selection
Off (up)
Off (up)
Automatic—Last connected. The last source
connected to the unit is routed to the output
Off (up)
On (down)
Automatic—Priority selection.
HDMI IN 1 HDMI IN 2 PC IN
(default, high to low priority)
Different priority cycles can be specified using the
Video & Audio Settings Web page
On (down)
Off (up)
Manual
On (down)
On (down)
Manual
Audio Switching Selection
DIP-switch 3
DIP-switch 4
Audio Input Selection
Off (up)
Off (up)
Automatic—Priority selection.
Embedded HDMI analog Audio IN
(high to low priority)
Off (up)
On (down)
Automatic—Priority selection.
Analog Audio IN embedded HDMI
(high to low priority)
On (down)
Off (up)
Embedded HDMI
On (down)
On (down)
Analog Audio IN
Step 6: Connect the power
Connect the 12V DC power adapter to the DIP-31M and plug it into the mains electricity.
Safety Instructions
Caution:
There are no operator serviceable parts inside the unit.
Warning:
Use only the power cord that is supplied with the unit.
Warning:
Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.
Warning:
Disconnect the power and unplug the unit from the wall before installing.
See www.KramerAV.com for updated safety information
Step 7: Operate the DIP-31M
To operate and control the DIP-31M use:
Front Panel
Buttons
HDMI IN 1 Select
HDMI IN 2 Select
PC IN Select
STEP-IN
Remote Control Switches
PC/HDMI—
input
selection/VGA
phase shift
adjustment
Short press—Input toggle
Long press—Adjusts the VGA
phase shift)
STEP IN
Activates the step-in function if
relevant
VOL UP—
analog audio
output volume
increase
control
Short press—Increases the
volume one step
Long press—Increases the
volume from 0% to 100% in 10
seconds
VOL DN—
analog audio
output volume
decrease
control
Short press—Decreases the
volume one step
Long press—Decreases the
volume from 100% to 0% in 10
seconds
GND
Connect to the common side of
the switches
Web Pages from IP 192.168.1.39
Technical Specifications
Inputs
Video:
2 HDMI on HDMI connectors
1 VGA on a 15-pin HD (F) connector
Audio:
1 Unbalanced stereo audio 1V RMS (nominal) on a 3.5mm mini jack
Outputs
Video:
1 HDMI on an HDMI connector
Audio:
1 Unbalanced stereo audio 1V RMS (nominal) on a 3.5mm mini jack
Ports
1 Ethernet on an RJ-45 connector
1 RS-232 3-pin terminal block control port
1 RS-232 3-pin terminal block data port
1 USB on mini USB connector
Controls
Remote switches for input switching, step-in, volume control, and device reset switch
Standards
HDMI with Deep Color, x.v.Color™ and 3D
HDCP 1.4 works with sources that support HDCP repeater mode
Maximum Analog Audio
Levels
3.1V p-p
THD
0.013%
SNR
75dB
Power Consumption
12V DC, 600mA
Operating Temperature
0° to +40°C (32° to 104°F)
Storage Temperature
–40° to +70°C (–40° to 158°F)
Humidity
10% to 90%, RHL non-condensing
Cooling
Convection
Enclosure Type
Aluminum
Dimensions
18.75cm x 11.5cm x 2.54cm (7.38” x 4.53” x 1.0”) W, D, H
Weight
0.43kg (0.95lbs) approx.
Shipping Dimensions
34.5cm x 16.5cm x 5.2cm (13.6” x 6.5” x 2.0”) W, D, H
Shipping Weight
1.03kg (2.3lbs) approx.
Environmental
Regulatory Compliance
Complies with appropriate requirements of RoHs and WEEE
Included Accessories
Power adapter
Warranty
7 years parts and labor
Autres manuels pour DIP-31M
3
Autres manuels Kramer Changer
Kramer
Kramer VP-733 Manuel utilisateur
Kramer
Kramer VS-66FW Manuel utilisateur
Kramer
Kramer VP-734 Manuel utilisateur
Kramer
Kramer RC-21TB Manuel utilisateur
Kramer
Kramer VP-774A Manuel utilisateur
Kramer
Kramer VP-734 Manuel utilisateur
Kramer
Kramer VP-81KSi Manuel utilisateur
Kramer
Kramer WP-211T Manuel utilisateur
Kramer
Kramer VM-10FW Manuel utilisateur
Kramer
Kramer VP-440 Manuel utilisateur
Kramer
Kramer VS-211UHD Manuel utilisateur
Kramer
Kramer VS-4FW Manuel utilisateur
Kramer
Kramer VS-44HN Manuel utilisateur
Kramer
Kramer VS-121HC Manuel utilisateur
Kramer
Kramer RC-11TB Manuel utilisateur
Kramer
Kramer VS-81H Manuel utilisateur
Kramer
Kramer VP-727A Manuel utilisateur
Kramer
Kramer VP-770 Manuel utilisateur
Kramer
Kramer WP-501 Manuel utilisateur
Kramer
Kramer VP-211DS Manuel utilisateur
