Kramer VS-8UFX Manuel utilisateur

VS-8UFX Quick Start (P/N: 2900-300846QS REV 1)

P/N:

2 9 0 0 - 3 0 0 8 4 6 Q S

Rev:

Scan for full manual

VS-8UFX Quick Start Guide

This guide helps you install and use your VS-8UFX for the first time.

Go to www.kramerav.com/downloads/VS-8UFX to download the latest user manual and check if firmware

upgrades are available.

Step 1: Check what’s in the box

VS-8UFX Programmable 8 port 12G SDI Router

1 Set of rack ears

1 Quick start guide

1 Power cord

4 Rubber feet

Step 2: Get to know your VS-8UFX

Feature

Function

POWER LED

Illuminates when the device is powered.

PORT Buttons

Press an output port (lights green) and then an input port (lights blue) to route an input to an output.

CLEAR Button

Press to clear a selection.

TAKE Button

Press to enter Take mode.

In Take mode,press several sets of output-input ports and then press TAKE to activate all the selected

routings at the same time.

When Take mode is off, each output-input pair is switched immediately.

LOAD Button

To load a preset configuration:

Press LOAD, press the appropriate PORTpreset button to select a preset configuration, and then press

TAKE to load that preset.

SAVE Button

To save the current port configuration to a PORT preset button:

Press SAVE, press the port button to which you want to save the configuration, and then press TAKE to

save the setup to that port.

INFO Button

Press to display general information, such as the firmware version and IP address.

Press INFO and then a specific PORT button to displaythe information of that selected port.

LCD Display Panel

Displays the current routing status, device information and so on.

LOCK Button

Press for 3 seconds (approx.) to lock the front panel buttons. When locked (button is lit), press again for 3

seconds (approx.) to unlock the front panel buttons.

Feature

Function

GENLOCK BNC Connector

Connect to the GENLOCK source.

LOOP BNC Connector

Connect to the GENLOCK connector of the next unit in the daisy chain.

PORTS BNC Connectors (8)

Connect to SDI sources and acceptors.

RS-232 (G,Rx,Tx) Terminal Block Connector

Connect to a PC or remote controller.

ETHERNET RJ-45 Connector

Connect to a PC via LAN and also use for firmware upgrade.

RESET Button

Press briefly to restart the system.

Press for 10 seconds to reset IP settings to factory default values.

The device powers up and loads the factory default values:

IP address: 192.168.1.39; Mask: 255.255.0.0; Gateway 192.168.0.1.

Power Socket

AC connector enabling power supply to the VS-8UFX.

Power Switch

Switch for turning the unit ON and OFF.

Step 3: Install VS-8UFX

Install VS-8UFX using one of the following methods:

Remove the three screws from each side of the unit, reinsert those screws through the

rack ears and mount on a 19" rack.

Attach the rubber feet and place the unit on a flat surface.

Step 4: Connect the inputs and outputs

Each VS-8UFX port can be defined as an input or an output, enabling flexible configurations such as 1x7 distribution amplifiers, 7x1

routers or any other possible input-output combination. By default, the VS-8UFX is set to operate as a 4x4 router: PORT 1 to PORT

4 as the inputs and PORT 5 to PORT 8 as the outputs.

Always switch OFF the power on each device before connecting it to your VS-8UFX. For best results, we recommend that you

always use Kramer high-performance cables to connect AV equipment to the VS-8UFX.

Optionally, daisy-chain the VS-8UFX by looping the genlock source to the next machine.

RJ-45 Pinout:

PIN EIA /TIA 568B

Wire Color

Orange / White

Orange

Green / White

Blue

Blue / White

Green

Brown / White

Brown

Step 5: Connect the power

Connect AC power to the rear of the VS-8UFX, switch on its power and then switch on the power on each device.

Safety Instructions

Caution:

There are no operator serviceable parts inside the unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Control the VS-8UFX via the front panel buttons and via the:

Web Pages:

RS-232 and Ethernet:

RS-232

Protocol 3000

Baud Rate:

115,200

Stop Bits:

Data Bits:

Parity:

None

Command format example (define port

6 as an output port):

#PORT-DIRECTION 1,IN

~01@PORT-DIRECTION 1,IN

TCP/IP Parameters

IP Address:

192.168.1.39

UDP Port #:

50000

Subnet Mask:

255.255.0.0

Maximum UDP Connections:

Default Gateway:

192.168.0.1

Maximum TCP Connections:

Unlimited

TCP Port #:

5000

Full Factory Reset

Web Page:

Device Settings Web page.

Protocol 3000:

#FACTORY<CR>

Rear Panel

RESET Button:

Press RESET for 10 seconds while the machine is on. The device

automatically resets and powers up again, loading factory default values.

To configure the ports via the Video Switching Web page:

Define a port as an input or output by clicking a port number.

Toggle Mute (M) on each output.

Click a white button in the matrix to switch an input to an output.

= current input to output routing state

= optional input to output routing

To route an input to an output using the front panel buttons:

1. Press an output (green) PORT button.

2. Press an input (blue) PORT button.

The selected input is swtiched to the selected output.

Technical Specifications

Ports

8 12G HD-SDI/HD-SDI/SDI

video

75Ω on BNC connectors (by default, 1 to 4 are set as inputs and 5 to 8 are

set as outputs)

1 Genlock

75Ω on a BNC connector

SMPTE Standards

12G-SDI

SMPTE ST-2082-1

3G HD-SDI

SMPTE 424M

HD-SDI

SMPTE 292M

SDI

SMPTE 259M/344M

Resolutions

Maximum Resolution

4K@60Hz (4:2:2)

Maximum Data Rate

12Gbps

Controls

Front panel

Buttons

LCD display

Power LED

Remote

RS-232

Ethernet

Web pages

Extension Range

Up to 300m for SD signals

Up to 200m for 1.5GHz HD signals

Up to 100m for 3GHz HD signals

Up to 100m for 6GHz HD signals

Up to 80m for 12GHz UHD signals

Coupling

Power

Consumption

100-240V AC, 33VA max.

Cooling

Fan Ventilation

Environmental

Conditions

Operating Temperature

0° to +40°C (32° to 104°F)

Storage Temperature

-40° to +70°C (-40° to 158°F)

Humidity

10% to 90%, RHL non-condensing

Regulatory

Compliance

Safety

Environmental

RoHs, WEEE

Enclosure

Size

19”, 1U

Type

Aluminum

General

Net Dimensions (W, D, H)

43.64cm x 18.3cm x4.36cm (17.18" x7.2" x1.72")

Shipping Dimensions (W, D, H)

55cm x 27.6cm x 10.7cm (21.7" x 10.87" x 4.21")

Net Weight

1.7kg (3.75lbs)

Shipping Weight

2.7kg (5.95lbs) approx.

Accessories

Included

Power cord

Specifications are subject to change without notice at www.kramerav.com

Table des matières

Autres manuels Kramer Routeur réseau

Kramer

Kramer FC-132ETH Manuel utilisateur

Kramer

Kramer VIA Capmus2 Manuel utilisateur

Kramer

Kramer FC-21ETH Manuel utilisateur

Kramer

Kramer RC-62 Manuel utilisateur

Kramer

Kramer RB-6 Manuel utilisateur

Kramer

Kramer FC-28 Manuel utilisateur

Kramer

Kramer FC-28 Manuel utilisateur

Kramer

Kramer RC-74DL Manuel utilisateur

Kramer

Kramer VS-162AVM Manuel utilisateur

Kramer

Kramer VS-8FDxl Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité