Konica Minolta Magicolor 7300 Manuel
magicolor 7300
Repacking Guide
®
1760538-001A
Trademarks
KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered
trademarks of KONICA MINOLTA HOLDINGS, INC.
magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING
SOLUTIONS U.S.A., INC. All other trademarks are the property of their respective
owners.
Copyright Notice
Copyright © 2003 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC., Marunouchi
Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. All Rights
Reserved. This document may not be copied, in whole or part, nor transferred to any
other media or language, without written permission of KONICA MINOLTA BUSINESS
TECHNOLOGIES, INC.
Manual Notice
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. reserves the right to make
changes to this manual and to the equipment described herein without notice.
Considerable effort has been made to ensure that this manual is free of inaccuracies
and omissions. However, KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
makes no warranty of any kind including, but not limited to, any implied warranties of
merchantability and fitness for a particular purpose with regard to this manual.
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. assumes no responsibility for,
or liability for, errors contained in this manual or for incidental, special, or
consequential damages arising out of the furnishing of this manual, or the use of this
manual in operating the equipment, or in connection with the performance of the
equipment when so operated.
Introduction 1
Introduction
Attention
Failure to follow these instructions could result in voiding your
warranty.
Relocating the Printer
How do I relocate my printer?
Occasionally, you may have to move your printer to a different location, either
nearby or to a distant location. To avoid damage to your printer, we advise
you to carefully follow the instructions below.
1Make sure you have turned off the printer and unplugged the power
supply cord and interface cable(s).
2Change the waste toner box (see “Preparing the Printer for Shipment” on
page 3).
3If the printer has accessories, such as a duplex unit kit or lower feeder
unit(s), remove them (see “Preparing the Printer for Shipment” on page
3).
Relocating the Printer
How do I relocate my printer? page 1
Storing the Printer
What do I do when storing the printer for an extended period? page 2
How do I care for media? page 3
Preparing the Printer for Shipment
How do I change the waste toner box? page 3
How do I remove the optional duplex unit kit? page 5
How do I remove the optional lower feeder unit(s)? page 8
Repacking the Printer
What's involved in repacking? page 12
Shipping the Printer
How do I ship my printer? page 18
Where can I get additional information? page 18
Storing the Printer2
4If you are moving the printer to a distant location, follow the instructions
for repacking the printer on page 12.
5Relocate the printer.
6Unpack and set up the printer in its new location.
7Reinstall the accessories you removed in step 3.
8Reconnect the power cord and interface cable(s).
Storing the Printer
What do I do when storing the printer for an extended
period?
1Make sure you have turned off the printer and unplugged the power cord
and interface cable(s)
2Remove the media from all media trays.
3Open the printer’s right side door.
Attention
Do not touch the wire harness or
connectors on the inside of the
right-side door, shown in the illustration.
Otherwise, the electronic parts of the
printer may be damaged by static
electricity from your body.
4Lower the two
fuser levers to
release the
spring pressure
from the fuser
rollers.
5Close the right
side door.
Left side Right side
Preparing the Printer for Shipment 3
6Protect the printer from extremes in temperature and humidity, and from
dust.
How do I care for media?
If media has been removed from its wrapper, place it in its original packaging
and store it in a cool, dark place.
When storing media, avoid:
Moisture and excess humidity
Keep media between 30% to 65% relative humidity. Toner does not
adhere well to moist or wet paper. On the other hand, media that has
been stored for a long time out of its packaging may dry up too much and
cause jamming.
Direct sunlight
Excess heat (above 86 °F/30 °C)
Dust
Leaning it against other objects or placing it in an upright position
Preparing the Printer for Shipment
Changing the Waste Toner Box
How do I change the waste toner box?
Attention
Before transporting the printer, remove the waste toner box and install a
new, empty one (included in the magicolor 7300 Series Return
Packaging Kit—part number 2600753-100).
1Make sure you have turned off the printer and unplugged the power
supply cord and interface cable(s).
2Open the printer’s front door.
Storage Conditions Normal Extreme
Temperature 32 to 95 °F (0 to 35 °C) –4 to 32 °F (–20 to 0 °C)
95 to 113 °F (35 to 45 °C)
Humidity 10–85% 85–90%
Preparing the Printer for Shipment4
3Grab the handles of a waste toner box
cover, and then attach it to the top of the
used waste toner box.
4Holding the handles of the cover, tilt the
used waste toner box toward you to
remove both the box and the cover.
WARNING!
Place the used waste toner box in a
plastic bag so that the waste toner
will not spill. Do not throw it into a
fire. Toner expelled from the fire may
cause burns.
Attention
recycling or disposal information.
5With a clean, dry cloth, lightly clean any toner spilled inside the printer.
6Place the new waste toner box
on the front door with the arrow
mark on the waste toner box
aligned with the arrow mark on
the inside of the front door.
7Hold both sides of the front door
and slowly close it.
The new waste toner box will
move into position.
8Close the printer’s front door.
Preparing the Printer for Shipment 5
Uninstalling Accessories
Attention
If a duplex unit kit and/or lower feeder unit(s) are installed, remove them
before transporting the printer.
How do I remove the duplex unit kit?
If you don’t have a duplex unit kit installed, skip to the next section.
1Make sure you have turned off the printer and unplugged the power cord
and interface cable(s).
2Pressing down the release levers (one on
each side), remove the manual feed tray.
3Remove the wire-releasing tool , which
was attached to the connector cover of
the duplex unit.
4Remove the connector cover of
the duplex unit.
Preparing the Printer for Shipment6
5Disconnect the two connectors of
the duplex unit.
6Pull the release lever for the duplex
unit cover to open the cover.
7Loosen the two shoulder screws within the cover.
8Close the duplex unit cover.
9Pull up the lock release lever to carefully
open the right-side door about 2" (5 cm).
Support the open right-side door with
your other hand.
Preparing the Printer for Shipment 7
10 Insert the end of the wire- releasing
tool into the wire lock.
When the wire-releasing tool is
inserted, the wire is unhooked and
wound up in the duplex unit with a
spring-like force.
11 With the right-side door still open, open
the cover of the duplex unit.
Attention
If you close the right-side door, the
wire locks again. Be sure to hold the
right-side door open with your left
hand while performing the following
steps.
12 Lift up the duplex-unit-locking hook
on the inside of the right-side door,
and then slowly open the duplex unit
about 1.2" (30 mm).
Attention
After the duplex-unit-locking hook
is lifted up, the duplex unit is
unlocked. Support the duplex unit
so that it does not fall.
Preparing the Printer for Shipment8
13 With the duplex unit cover open, close just
the right-side door.
Attention
If the right-side door is also closed when the duplex unit cover is
closed, the wire locks again.
14 Lift up the duplex unit with both
hands to remove it.
15 Store it in a safe place.
16 Replace the original upper-right
side cover and secure it with its
two screws.
How do I remove the optional lower feeder unit(s)?
If you don’t have optional lower feeder unit(s) installed, skip to the next
section.
The following illustrations assume that you have both Trays 3 and 4
attached. Trays 3 and 4 should stay attached together.
1Make sure you have turned off the printer and unplugged the power
supply cord and interface cable(s).
Autres manuels pour Magicolor 7300
5
Table des matières
Autres manuels Konica Minolta Imprimante
Konica Minolta
Konica Minolta magicolor 1690MF Manuel utilisateur
Konica Minolta
Konica Minolta A0VD011 Instructions originales
Konica Minolta
Konica Minolta bizhub PRESS C70hc Instructions originales
Konica Minolta
Konica Minolta Magicolor 2550 Manuel
Konica Minolta
Konica Minolta DRYPRO SIGMA Manuel utilisateur
Konica Minolta
Konica Minolta magicolor 4750EN/4750DN Manuel utilisateur
Konica Minolta
Konica Minolta Magicolor 5570 Manuel utilisateur
Konica Minolta
Konica Minolta Magicolor 2300W Manuel utilisateur
Konica Minolta
Konica Minolta PagePro 1380 MF Guide de démarrage rapide
Konica Minolta
Konica Minolta Color Care IQ-501 Manuel utilisateur
Konica Minolta
Konica Minolta bizhub Colour Series Guide de l'administrateur
Konica Minolta
Konica Minolta bizhub 3301P Manuel utilisateur
Konica Minolta
Konica Minolta bizhub PRESS C8000 Manuel utilisateur
Konica Minolta
Konica Minolta Magicolor 5550 Manuel utilisateur
Konica Minolta
Konica Minolta Magicolor 5430 DL Manuel utilisateur
Konica Minolta
Konica Minolta PagePro 1400W Manuel utilisateur
Konica Minolta
Konica Minolta bizhub 4050 Manuel utilisateur
Konica Minolta
Konica Minolta bizhub 223 Manuel
Konica Minolta
Konica Minolta PagePro 1400W Manuel utilisateur
Konica Minolta
Konica Minolta Magicolor 2500W Manuel utilisateur
