Konica Minolta DiMAGE Z3 Manuel utilisateur

www.konicaminolta.com

www.konicaminoltasupport.com

DiMAGE Z3 Camera Firmware Ver.1.03e

This section explains how to install DiMAGE Z3 firmware version 1.03e. (Firmware is software used

internally to control the camera.) Be sure to read through the following explanation before you

install the software. Do not turn the camera OFF during installation; doing so could damage the

CPU inside the camera.

Contents of update

To support 2GB SD memory card.

Target products

This firmware is for use only with the DiMAGE Z3 and cannot be used with other products.

If the firmware version is already Ver.1.03e, it is not necessary to update the firmware. (Check the

firmware version as shown below.)

Checking the camera firmware version

1. Press the main switch to turn ON the camera.

2. Press the menu button.

3. Press the right key of the controller, select SETUP icon,

and press the center of the controller to display the

setup menu.

4. Confirm that the section 1 menu tab is highlighted, and

press the macro mode button. A window will open to

indicate the firmware version.

5. Check the version number of displayed on the LCD mon-

itor. If the version is Ver.1.02e or earlier, the camera must

be updated.

Press the central button of controller to close the version

number display.

KONICA MINOLTA SOFTWARE INSTALL GUIDE

1. Two respective download files have been prepared for Windows & Macintosh. Please use the

suitable one for your PC. Please read the end-user license agreement in advance of saving the

file on your PC.

The downloaded file is compressed.

-Windows- z3v103e.exe--808KB

Double-click the downloaded file.

The file is a self-extracting archive, and decompresses automatically.

-Macintosh- z3v103e.sea.hqx--1.1MB

Use Stuffit Expander or another such software utility to extract the downloaded file.

*After creating a folder in your PC and extracting the contents of the archive, the following folder is

created.

"z3v103" folder "z3v103" folder includes bellow files.

"dsc.app" file (Windows 2.07MB / Macintosh 2.1MB)

"ram.bin" file (Windows 92.9KB / Macintosh 96KB)

* Copy the "dsc.app" file and "ram.bin"

file onto the SD memory card.

For Windows For Macintosh

When copying via CompactFlash card reader When copying via DiMAGE Z3 connected to

PC using USB-cable USB-2

Preparing the SD memory card for updating

A downloaded file must be copied to a SD memory card in the camera. Before updating the cam-

era, read the data-transfer section of the DiMAGE Z3 instruction manual to connect the camera to

a computer.

• Prepare a 8MB or larger SD memory card and insert it in the camera.

• Make sure that the SD memory card has been formatted by the camera.

• Using the USB cable, connect the camera to a computer. If the camera is not compatible

with the computer system, a SD memory card reader can be used instead.

• Confirm the option “Transfer mode” in section 1 of the setup menu is set to “Data storage”,

the default setting.

2.Confirm that the file has been copied to the card using the computer.

3.Disconnect the camera from the computer or remove the SD memory card from the

card reader.

If you are using Windows Me, 2000 or XP, click the unplug-or-eject-hardware icon

in the lower right-hand corner of the screen, wait until the safe-to remove-hardware

window appears, then remove the SD memory card the card reader, or disconnect

the USB cable from the camera.

How to update firmware

NOTE:

When performing the software update, use new Alkaline batteries, fully recharged Ni-MH batteries

or the AC adapter AC-1L or AC-11 (sold separately).

When using the AC adapter, be sure not to inadvertently disconnect the camera during the soft-

ware updating procedure, otherwise the camera may be permanently damaged.

* After updating the firmware, it is necessary to operate the reset default function, and camera

settings will be reset to the default settings.

1. With the camera off, insert the prepared SD Memory

card.

2. Press and hold the shutter-release button all the way

down without turning on the camera.

3. Without lifting the your finger from the shutter-release

button, press the main switch to turn on the camera.

4. The access lamp will be lit. Please wait until the lamp

turn off. (It takes 1 or 2 minutes. You can release your

fingers from the shutter-release button and the main

switch.)

5. When the access lamp turns off, updating is completed.

Remove the batteries and then insert them again.

(When using AC adapter, disconnect the AC adapter

and then connect it again.)

6. Check that the camera firmware version number has

changed to "Ver.1.03e". (See the "Checking the camera

software version")

* If the updating failed or an error occurred during the

procedure, turn the camera off, and repeat the proce-

dure from step 1.

After checking the version number, press the center

button of controller. Setup menu will be displayed.

* After updating the camera, delete both "dsc.app" and "ram.bin" files from the SD memory card.

* Windows and Windows Me, 2000 and XP are registered trademarks of Microsoft Corporation in the U.S.A and other countries.

* Macintosh is a registered trademark of Apple Computer Inc. in the U.S.A. and other countries.

For questions or comments about this matter, contact your nearest Konicaminolta service facility.

07.2005/12984

Autres manuels pour DiMAGE Z3

Table des matières

Autres manuels Konica Minolta Appareil photo numérique

Konica Minolta

Konica Minolta e-mini M Manuel utilisateur

Konica Minolta

Konica Minolta Q-Mini Manuel utilisateur

Konica Minolta

Konica Minolta Digital Revio KD-400Z Manuel utilisateur

Konica Minolta

Konica Minolta KD-25 Manuel utilisateur

Konica Minolta

Konica Minolta Digital Revio KD-500Z Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE X31 Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE E500 Manuel utilisateur

Konica Minolta

Konica Minolta DINAX MAXXUM 7D Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE Z3 Manuel utilisateur

Konica Minolta

Konica Minolta Q-Mini Manuel utilisateur

Konica Minolta

Konica Minolta Dimage A1 Manuel utilisateur

Konica Minolta

Konica Minolta Digital Still Camera Revio KD-3300 Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE X31 Manuel utilisateur

Konica Minolta

Konica Minolta DIMAGE X1 9979-2801-80/12984 Manuel

Konica Minolta

Konica Minolta DYNAX 30 - PART 2 Manuel utilisateur

Konica Minolta

Konica Minolta E-Mini-M E-Mini-Multi-Media Camera Manuel utilisateur

Konica Minolta

Konica Minolta REVIO KD-420Z Manuel utilisateur

Konica Minolta

Konica Minolta MAXXUM 5D Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE Z1 Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE X31 Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE Z6 Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE G500 Manuel utilisateur

Konica Minolta

Konica Minolta Dynax DYNAX 5D Manuel

Konica Minolta

Konica Minolta Top's AF-300 SP Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur