Kolibri KCD-1000 Manuel

2019 Kolibri USAKB-062019

Cleaning Procedure

KCD-1000

Dirty sensors can affect the KCD-1000 performance and cause genuine bills to be rejected. It is suggested that

the user performs weekly maintenance on the unit to maintain top performance.

Items Needed

- Soft microfiber cloth

- Soft-bristled brush

- Can of compressed air

- Isopropyl alcohol

Steps

1. First, make sure the unit is turned off and unplugged

2. Perform the cleaning of each sensor, one step at a time (a to c), and check after each step if this

resolves the issue. If it does not, proceed to the next cleaning step

a. Wipe away dust with a soft microfiber cloth or a soft-bristled brush

b. Clean the sensors using a can of compressed air

c. Clean the sensors with a cotton swab lightly moistened with isopropyl alcohol – gently wipe

the sensors with the swab

Refer to the photos below showing the location of the KCD-1000 sensors. For each sensor, follow the steps as

described above.

Sensors Locations

Overview:

1. UV Sensor

2. IR Sensors

3. Magnetic Sensors

4. Start Sensor

KB-062019 2019 Kolibri USA

KCD-1000

Cleaning Procedure

Infrared (IR) Sensor:

Locate the small square sensor on the upper part of the bill track as shown below.

Ultraviolet (UV) Sensor:

Locate the 4-part UV sensors as shown below. These pairs of sensors are spaced between the

MG Sensors (metal bar).

KB-062019 2019 Kolibri USA

KCD-1000

Cleaning Procedure

Magnetic (MG) Sensor:

Locate the 2 magnetic sensors, which looks like a small metal bar and are found at the top middle of the bill

track as shown below.

Start Sensor:

Locate the 2-part start sensor as shown below. These pair of sensors are seated in the front part of the unit,

between the 2 rollers.

Note: Several factors can cause a KCD-1000 to not recognize a genuine bill:

- Overly wrinkled, overly creased, and overly worn bills

- Dropping the unit or bumping into the unit during use

- A harsh change in temperature

- Extended period of non-use

- Improper maintenance or lack of preventative maintenance/cleaning

If, after cleaning all sensors, this does not resolve the issue, please see the support section on the Kolibri USA

website at www.kolibriusa.com, or contact Kolibri Support at suppor[email protected]

for further troubleshooting.

Table des matières

Autres manuels Kolibri validateur de billets de banque

Kolibri

Kolibri Domino Manuel utilisateur

Kolibri

Kolibri Bishop Manuel utilisateur

Kolibri

Kolibri Signature Manuel utilisateur

Manuels validateur de billets de banque populaires d'autres marques

Alberici

Alberici BILLYONE UN1 Manuel utilisateur

Royal Sovereign

Royal Sovereign RCD-2000 Manuel utilisateur

Innovative Technology

Innovative Technology BV100 Manuel utilisateur

Innovative Technology

Innovative Technology NV4 Manuel utilisateur

Innovative

Innovative NV200 Manuel utilisateur

Inves

Inves Secureuro Plus Manuel utilisateur

ICT

ICT Bill Validator S7 Series Manuel utilisateur

CUMMINS ALLISON

CUMMINS ALLISON JetScan Manuel utilisateur

Hamilton

Hamilton XE Guide de démarrage rapide

CashCode

CashCode AMZ-154 Manuel utilisateur

Innovate Technology

Innovate Technology NV10 Manuel utilisateur

JCM

JCM iVIZION Manuel

Innovative Technology

Innovative Technology NV10 Family Manuel utilisateur

Amrotec

Amrotec MIB-11F Manuel utilisateur

Crane

Crane NRI G-13.mft Standard Manuel utilisateur

CASH TECHNOLOGY

CASH TECHNOLOGY CCE 20 Manuel utilisateur

JCM

JCM VEGA Series Manuel utilisateur

JCM

JCM TBV Series Guide d'installation