Kohler K-18492 Manuel utilisateur
Installation Guide
Bath Filler with Handshower
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-18486 K-18492
1054455-2-B
Tools and Materials
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Before You Begin
IMPORTANT! For freestanding installations: Discard the following
hardware provided with the K-18486 bath filler: support plate (1),
threaded brass tubes (2), nuts (4), gaskets (4), and screws (8).
IMPORTANT! For freestanding installations: Do not remove the
protective wrap from the riser tubes until instructed to do so.
This product may be installed as freestanding (installed onto riser
tubes) or deck-mount (installed onto the bath deck). Follow the
sections that pertain to your particular installation.
Please read all instructions before you begin.
Shut off the water supply.
Observe all local plumbing and building codes.
IMPORTANT! For proper drainage of the spout, install the bath
filler to a level surface.
Before installation, unpack the new faucet trim and inspect it for
damage. Return it to the carton until installation.
Adjustable
Wrench Strap
Wrench Hacksaw or
Tubing Cutter Propane
Torch
Plumbers
Putty
Assorted
Screwdrivers Solder
1-1/2" Thin Wall
Socket Wrench
Hex
Wrenches
Drill and
Hole Saw Thread
Sealant
Small
Level
1054455-2-B 2 Kohler Co.
Before You Begin (cont.)
Kohler Co. reserves the right to make revisions in the design of
faucets without notice, as specified in the Price Book.
Kohler Co. 3 1054455-2-B
Rough-In - Freestanding Installation
To properly plan for the installation, use the cut-out template provided
with your bath along with the roughing-in dimensions above.
2-15/16" (7.5 cm)
2-5/8"
(6.7 cm) D.
14-1/16"
(35.7 cm) 5-3/4"
(14.6 cm)
11-1/4"
(28.6 cm)
21-15/16"
(55.7 cm)
No change in measurements if connected
with drain illustrated. (K-11344)
8" (20.3 cm)
5-9/16" (14.1 cm)
22" (55.9 cm)
1054455-2-B 4 Kohler Co.
Rough-In - Deck-Mount Installation
NOTE: If the bath filler is installed with the K-11343 drop-in bath,
ensure the distance between the centerline of each marked hole and
the flange contacting the bath deck is maximum of 4″(10.2 cm).
To ensure that water will not drip outside of the bath, properly
position the faucet on the deck so the outlet will be located inside the
bath.
To properly plan for the installation, use the cut-out template provided
with your bath along with the roughing-in dimensions above.
2-15/16" (7.5 cm)
2-5/8"
(6.7 cm) D.
14-1/16"
(35.7 cm) 5-3/4"
(14.6 cm)
11-1/4"
(28.6 cm)
8" (20.3 cm)
5-9/16" (14.1 cm)
Kohler Co. 5 1054455-2-B
1. Assemble the Bath Filler - All Installations
NOTE: The arms included with the bath filler are NOT identical.
The screw hole on each arm should face toward the bath filler body.
Determine the left and right-side arms. The setscrew hole for each
arm should face the bath filler body.
Apply lubricant (provided) to the O-rings on the bath filler body.
Insert the short side of the arms into the bath filler body.
Secure each arm to the bath filler body with a large setscrew.
Orient the handshower bracket with the large side of the taper
facing up.
NOTE: The handshower bracket should be assembled perpendicular
to the arm to ensure the handshower hangs over the bath.
Slide the handshower bracket onto the arm for the hot water
supply, then secure with the small setscrews at the desired height
on the arm.
Arm Arm
Large Setscrew
Small Setscrew
Small Setscrew
Handshower Bracket (large side up)
Bath Filler Body
1054455-2-B 6 Kohler Co.
2. Prepare the Site - Freestanding Installation
Mark the location of the water supply lines from the bath drain.
Use the template provided with the riser tubes to assist you.
Verify the distance between the centerline of the marked holes is
5-29/32” (15 cm) ± 0 and the distance between the centerline of
each marked hole to the centerline of the drain outlet is 22” (55.9
cm).
Drill the marked holes using a 1-5/8” spade drill bit or hole saw.
Insert the riser support through the drilled holes.
Secure the riser support to the subfloor with eight wood screws
(provided).
NOTE: To protect the riser support from debris when installing the
finished floor, you may remove the thread protectors from the riser
tubes, then place the thread protectors into the holes of the riser
support.
Install the 1/2″OD water supply tubing.
Install the finished floor material.
Measure and mark 20-3/8″(51.8 cm) up from the surface of the
finished floor onto the water supply tubes. Cut the water supplies
tubes to this height.
Subfloor
Riser
Support
Drain
Outlet
Wood Screw
5-29/32
(15 cm) ±0
22"
(55.9 cm) Finished
Floor
21-1/4"
(54 cm)
20-3/8"
(51.8 cm)
Water Supply
Tubing
Male Copper
Connections
Kohler Co. 7 1054455-2-B
Prepare the Site - Freestanding Installation (cont.)
Solder 1/2″male copper connections to the water supply lines.
The measurement to the top of these connections should be
approximately 21-1/4″(54 cm) from the surface of the finished
floor.
Apply thread sealant to the male copper connections on each
water supply tube.
1054455-2-B 8 Kohler Co.
3. Install the Riser Tubes - Freestanding Installation
Thread the riser tubes down into the riser support until the riser
tubes almost bottom out. Do not completely tighten the riser
tubes into the riser support.
NOTE: The distance from the surface of the finished floor to the top
of the installed coupling assemblies must be approximately 24-1/8″
(61.3 cm).
Thread a coupling assembly onto each water supply connection,
then tighten with a wrench.
Install the plastic pipe plugs (provided) into each coupling
assembly.
Turn on the main water supply.
Check for leaks. Adjust as needed.
Turn off the main water supply.
Remove and discard the plastic pipe plugs.
Thread the riser tubes out of the riser support, then thread the
riser tubes up onto the coupling assemblies until hand-tight.
Slide an escutcheon with gasket (supplied in the bath filler
hardware pack) over each riser tube and against the surface of the
finished floor. The setscrew holes on each escutcheon should face
toward the side of the bath.
Secure each escutcheon in place with a small setscrew.
Escutcheon
Riser Tube
Plastic Pipe Plug
Finished Floor
Finished Floor Level
Gasket
Water Supply
Tubing
Coupling
Assembly
Riser
Tube 24-1/8"
(61.3 cm)
Small Setscrew
Kohler Co. 9 1054455-2-B
4. Construct the Tee Assembly - Freestanding Installation
Thread the fastener support into the side of the bath with a 1/4″
hex wrench. Do not overtighten.
Ensure the distance from the head of the fastener support to the
bath surface is approximately 1/2″(1.3 cm).
Thread the fastener rod into the fastener support.
Thread a bracket onto one end of tee rod until hand-tight.
Slide the tee rod through the center hole of the tee.
Hand tighten the remaining bracket onto the other end of the tee
rod to construct the tee assembly.
Ensure the center-to-center distance between the brackets aligns
with the center-to-center distance of the installed riser tubes.
Slide the tee assembly down onto the installed riser tubes. Do not
secure the tee assembly at this time.
Tee
Tee Rod
Bath
Bracket
Fastener Support
Fastener
Rod
Fastener
Support
Fastener
Rod
1/2"
(1.3 cm)
1054455-2-B 10 Kohler Co.
Ce manuel convient aux modèles suivants
4
Table des matières
Langues :
Autres manuels Kohler Équipements de cuisine et de salle de bain
Kohler
Kohler Renew 76367T Manuel utilisateur
Kohler
Kohler Sterling SC3322DBG Instructions de montage
Kohler
Kohler K-11075 Instructions de montage
Kohler
Kohler ELATE 13963T-B4 Manuel utilisateur
Kohler
Kohler K-8802 Instructions de montage
Kohler
Kohler Pinoir K-2017 Instructions de montage
Kohler
Kohler Margaux 72627T Manuel utilisateur
Kohler
Kohler K-498 Manuel utilisateur
Kohler
Kohler K-72218 Instructions de montage
Kohler
Kohler LOURE 98337T-C Manuel utilisateur
Kohler
Kohler Revival K-16112 Instructions de montage
Kohler
Kohler K-2205 Manuel utilisateur
Kohler
Kohler K-5811 Manuel utilisateur
Kohler
Kohler Sterling 14700 Manuel utilisateur
Kohler
Kohler WHIRLPOOL Manuel utilisateur
Kohler
Kohler rada TD7 Manuel utilisateur
Kohler
Kohler K-5814 Manuel utilisateur
Kohler
Kohler K-1737-K1 Instructions de montage
Kohler
Kohler K-18597 Manuel utilisateur
Kohler
Kohler LOURE K-98454T-B-CP Manuel utilisateur
Manuels Équipements de cuisine et de salle de bain populaires d'autres marques
Alpha Bidet
Alpha Bidet Alpha One Manuel utilisateur
InSinkErator
InSinkErator H/HC3300 Manuel d'installation
Clou
Clou Xo type 1 Manuel utilisateur
Grohe
Grohe Bridgeford 20 158 Manuel utilisateur
Hans Grohe
Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Manuel utilisateur
Wickes
Wickes MONO SINK MIXER Manuel utilisateur