Kobalt SGY-AIR266 Manuel utilisateur
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call
our customer service department at 888-3KOBALT, 8:00 a.m. - 8:00 p.m.,
1
SS22196
50 ft Pro Retractable
Hose Reel with Premium
Rubber Air Hose
KOBALT and logo design are trademarks
or registered trademarks of LF, LLC.
All rights reserved.
Español p. 11
ITEM #5091975
MODEL #SGY-AIR266
TABLE OF CONTENTS
2
Safety Information .................................................................................................4
3
Preparation ............................................................................................................5
5
6
Installation Preparation .........................................................................................
Assembly Instructions ...........................................................................................
Operating Instructions ...........................................................................................8
8
8
9
Care and Maintenance ..........................................................................................
Troubleshooting ....................................................................................................
Warranty ...............................................................................................................
10Replacement Parts List .......................................................................................
Package Contents ................................................................................................
PACKAGE CONTENTS
3
DESCRIPTION
Retractable Hose Reel
Air Hose (50 ft.)
Lead Hose (3 ft.)
Bottom Base Plate
Air Inlet
Air Outlet
Hose Guide
Bumper
Roller Bracket
Screw
Reel Bracket
QUANTITY
1
1
1
1
1
1
1
1
2
6
2
PART
A
B
C
D
F
E
G
H
I
J
K
A
K
F
I
H
B
G
J
HARDWARE CONTENTS
AA BB
C
D
ST6.3 × 45 mm Lag Bolt
Qty. 4
E
Plastic Anchor
Qty.4
4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate
or install the product. If you have any questions regarding the product, please call
customer service at 888-3KOBALT, 8:00 a.m.- 8:00 p.m., EST, Monday-Sunday.
WARNING
Improper assembling or operation of this product could result in serious injury or
property damage. Read and understand all assembly and operation instructions.
Never remove side cover while hose is under tension. Serious injury could occur.
Keep hose away from sharp edges. Check hose for wear before each use.
Do not exceed maximum pressure of 300 PSI. Use compressed air regulated to
a maximum pressure at or below the reated pressure of any attachments to this
product.
Protect your eyes by wearing safety glasses or a face shield when mounting and
using this product.
Keep loose clothing, hair, and jewelry away from moving parts of hose reel.
Make sure that the product is firmly mounted before pressurizing.
Rapidly retracting hose could cause injury and property damage. Maintain control
of hose as it retracts.
When securing the hose reel assembly
to any type of wood, make sure it is thick enough
to not only support the hose reel, but the force
required to extend and retract the air hose.
See fig 2.
Ensure there are no live electrical wires
or plumbing in the wall at the location you are
drilling.
Before assembling the product, make sure there are no missing parts. Compare parts
with package contents list and hardware contents list. If any part is missing or
damaged, do not attempt to assemble the product.
Estimated Assembly Time: 10-15 minutes
Tools Required for assembly and installation (not included):
3/8" (10 mm) Wrench
3/16" (5 mm) Allen Wrench
Sealant Tape
PREPARATION
INSTALLATION PREPARATION
5
9/16" (14 mm) wrench
Drill & 3/8" Drill Bit
Pencil
Level
1. Using the provided paper template tape it to
the location you are going to hang the
retractable hose reel. See fig 1.
NOTE
NOTE
1
2
ASSEMBLY INSTRUCTIONS
6
1. Using the 3/8" drill bit, drill 4 holes and install
the 4 plastic anchors provided. See fig 1.
2. Using the 3/8" wrench screw 2 of the mounting
screws into the lower left and upper right,
leaving about 6 mm (1/4-in) between the wall
and screw head.
3. Hang the hose reel on these 2 screws. Slide
down the screw slid onto the small end of holes
on the base plate (D). See fig 2.
4. Tightly tighten the 2 screws to the mounting
bracket. See fig 2.
5. Install and tighten down the 2 remaining
screws. See fig 3.
6. Wrap 3-5 layers of sealant tape on both male
plug ends of the leader hose (C). Screw one
end into the air inlet (E). Use a 9/16" (14mm)
wrench to tighten together. See fig 4.
EC
4
2
3
1
AA
D
BB
BB
When loosening or removing the screws (J) on each side be careful that
the hose reel does not spin freely and cause the hose reel to lose tension.
If the desire angle is larger than 90
degrees, take off 3 screws (J) on each side,
rotate the roller bracket to the desire position,
and reassemble and tighten the 3 screws.
ASSEMBLY INSTRUCTIONS
7
H
8.Pull out the hose to the desired length (ensure
the hose reel is locked as it will not rewind),
open the latch on the bumper (H) and move it
to the desired location. Re-latch the
bumper (H). See fig 6.
6
7. Depending on your setup you can either attach
a female inlet plug or a female quick
disconnect to the other end of the leader hose.
See fig 5.
5
9. The roller bracket (I) can be adjusted to the
best angle/position for the smoothest
operation of hose reel (A) when the hose reel
is mounted. Loosen three screws (J) on each
side with 5/16 (5mm) allen Wrench, rotate the
roller bracket (I) to the desired position, then
tightly tighten the three screws (J) on each
side. See fig 7.
7I
J
NOTE
WARNING
To avoid damaging the hose reel (A), always hold on to air hose (B) while it is
rewinding.
1. To extend air hose (B), slowly extend air hose to desired length. The hose reel will
make a “clicking” sound as the hose is pulled out. The clicking sound you hear is
the drum locking into place so it will not retract when you let go of the air hose. It
may be necessary to pull air hose beyond desired length to keep it from
automatically retracting.
OPERATING INSTRUCTIONS
CARE AND MAINTENANCE
Always operate the product with care by following the operating instructions.
NOTE
TROUBLESHOOTING
If you have any questions regarding the product, please call customer service at
888-3KOBALT, 8:00 a.m.- 8:00 p.m. EST, Monday-Sunday. You could also contact
2. To retract, slowly pull air hose (B) until clicking stops. While holding the air hose,
let the hose automatically draw back until the bumper (I) stops against the hose
guide (H).
PROBLEM CORRECTIVE ACTIONPOSSIBLE CAUSE 1. Adjust roller bracket in the
best angle/position.
2. Replace roller bracket.
Air hose cannot be
pulled smoothly or
blocks.
1.
Roller bracket is not adjusted
in the best angle/position.
2. Roller bracket is damaged.
8
Air hose will not
retract smoothly.
Air hose will not
retract all the way.
2. Roller bracket is damaged.
1. Not enough tension on the
coil spring.
1. Adjust roller bracket in the
best angle/position.
2. Replace roller bracket.
1.
Roller bracket is not adjusted
in the best angle/position.
Pull out approximately 6-ft of
hose, and lock hose in place.
Remove the bumper (H) from
the hose and slide the hose out
of hose gudie (G) so the hose is
hanging loose.
A.To increase tension, wrap the
loose hose one time around the
reel drum.
B.To decrease tension, unwrap
the hose one time from the drum.
- Run the hose back through the
hose gudie (G) and reattach
the hose stopper.
- Pull the hose out several feet
to check the tension.
9
WARRANTY
This tool is warranted by the manufacturer to the original purchaser from the original
purchase date for one (1) year subject to the warranty coverage described herein.
This tool is warranted to the original user to be free from defects in material and
workmanship. If you believe that a tool is defective, return the tool, with proper proof
of purchase to the point of purchase. If it is determined that the tool is defective and
covered by this warranty, the distributor will replace the tool or refund the
purchase price.
This warranty is void if: defects in materials or workmanship or damages result from
repairs or alterations which have been made or attempted by others or the
unauthorized use of nonconforming parts; the damage is due to normal wear,
damage is due to abuse (including overloading of the tool beyond capacity),
improper maintenance, neglect or accident; or the damage is due to the use of the
tool after partial failure or use with improper accessories or unauthorized repair or
alteration.
This warranty gives you specific legal rights, and you may also have other rights that
vary from state to state.
For warranty questions, call our customer service department at 888-3KOBALT,
8:00 a.m.- 8:00 p.m. EST, Monday-Sunday. You could also contact us at
Printed in China
10
REPLACEMENTPARTS LIST
10
1
7
4
12
13
11
3
2
14
16
8
6
5
1
1
15
11
1
1
7
11
PART DESCRIPTION QTY
1 18
1
1
1
2
1
1
3
1
Allen Screws for Adjusting Arms
2 Locking Finger
3 Locking Finger Spring
4 Locking Gear
5 Bumper
6 Snap Ring
7 Blue Arm
8 Black Mounting Plate
9 Black Arm Left Side
PART DESCRIPTION QTY
10 1
9
1
1
1
1
1
Black Arm Right Side
11 Guide Assemblt w/Screws
12 Nut and Lock Washer
13 Shaft
14 Brass Air Inlet Fitting
15 Bend Restrictor Spring
16 Hardware Pack
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels Kobalt Outils
