Kobalt 3300243 Manuel utilisateur

AB17966

KOBALT® and the K Design® are registered

2 GAL QUIET TECH AIR COMPRESSOR

ITEM #0905517

MODEL #3300243

Français p.13

Español p.25

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-3KOBALT (1-888-356-2258), 8 a.m. - 8 p.m., EST,

Monday - Friday.

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

TABLE OF CONTENTS

PRODUCT SPECIFICATIONS

Model No. 3300243

Power Cord

CFM @ 90 PSI

CFM @ 40 PSI

Cut-out Pressure

Cut-in Pressure

Air Tank Capacity

Voltage/Amps/Hz

SJT18 AWG / 72 in. length

1.7

2.8

125 PSI

95 PSI

2 gallon

120 / 5.7 / 60

Pump

Motor 3/4 HP

Oil free, direct drive, single stage

NOTE:Avoid use of extension cords. If use of an extension cord cannot be avoided, the cord

should be a minimum wire size of 14 AWG and no longer than 100 ft.

Use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that

will accept the plug on the product.

Specifications

Package Contents

Parts Description

Safety Information

Operating Instructions

Care and Maintenance

Troubleshooting

Warranty

Replacement Parts List

Preparation

PACKAGE CONTENTS

PART QTY

AElectric Motor & Air Compressor Pump

BAir Tank

Tank Pressure Gauge

DAir Pressure Regulator

ERegulated Pressure Gauge

Quick Coupler

GDrain Valve

Safety Valve

ION/OFF Switch

JPower Cord

DESCRIPTION

PARTS DESCRIPTION

PART PART NAME PART DESCRIPTION

A Electric Motor The motor is used to power the pump. It contains a thermal

overload protector. If the motor overheats for any reason,

the thermal overload protector will shut it down in order to

prevent the motor from being damaged.

The pump is used to compress the air and discharge it into

the tank via the piston moving up and down in the cylinder.

B Air Tank The tank is used to store the compressed air.

C Tank Pressure Gauge The gauge is used to measure the stored air pressure level of

the tank. It is not adjustable by the operator and does not

indicate line pressure.

D Air Pressure Regulator The regulator is used to adjust line pressure to the tool you are

using. Turn the knob clockwise to increase pressure and

counterclockwise to decrease pressure.

E Regulated Pressure Gauge The gauge is used to measure the regulated outlet pressure.

F Quick Coupler For this compressor, the quick coupler is also used as

the air line outlet. The outlet is used to connect the 1/4

in. air hose.

G Air Tank Drain Valve The drain valve is used to remove moisture from the air tank

after the unit is shut off.

H Pressure Relief Valve The valve is used to prevent system failures by relieving

pressure from the system. If the pressure reaches the preset

level and the pressure switch will not shut down the motor, it

will automatically pop open. You can also pull the ring on the

valve to open.

I On/Off Switch

J Power Cord

Grounded

outlet

Grounding Pin

Plug

Air Compressor Pump

This switch turns on the compressor and is operated manually.

When in the ON position, it allows the compressor to start up

or shut down automatically, without warning, upon air demand.

ALWAYS set this switch to OFF when the compressor is not

being used and before unplugging the compressor.

This product is for use on a nominal 120-volt circuit and

should be grounded. A cord with a grounding plug as

illustrated must be used. Make sure that the product is

connected to an outlet that has the same configuration as

the plug. No adapter should be used with this product.

SAFETY INFORMATION

DANGER

Improper installation of the grounding plug will result in a risk of electric shock. If repair or

blade terminal. The grounding wire has a green outer surface.

WARNING

•

motor and pressure switch to produce sparks while operating. If sparks come into contact with

as far from the spray area as possible. Always operate the compressor in a well-ventilated area.

•Risk of electric shock. A licensed electrician must install all wiring in accordance with all local

and national codes. To avoid electric shock, never use an electric air compressor outdoors

when it is raining or on a wet surface.

•Risk of bursting. Rust can weaken the tank. Drain the condensed water from the tank after

each use to reduce rusting. Do not weld, drill or modify the air tank of this compressor. Welding

hazardous condition. If a leak is detected in the tank, replace the tank immediately.

•Risk of injury. Always shut off the compressor, remove the plug from the outlet and bleed all

pressure from the system before servicing the compressor or when the compressor is not in

use. Do not use the unit with the shrouds removed. Contact with moving parts could cause

serious injury.

•Risk of bursting. Check the maximum pressure rating in the manual or the serial tag label.

Compressor outlet pressure must be regulated so as to never exceed the maximum pressure

rating. Relieve all pressure through the hose before removing or attaching accessories.

Please read and understand this entire manual before attempting to assemble, operate or install

the product. If you have any questions regarding the product, please call customer service at

1-888-3KOBALT, 8 a.m. - 8 p.m., EST, Monday - Friday.

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols

and the explanations that accompany them deserve your careful attention and understanding. The

safety warnings DO NOT, by themselves, eliminate any danger. They are not substitutes for proper

accident-prevention measures.

User Safety

•Risk of bursting. Do not adjust the pressure switch or relief valve for any reason. They

have been preset at the factory for the maximum pressure of this unit. If the pressure

switch or the relief valve are tampered with, personal injury or property damage may occur.

Risk of burns. The pump and manifold generate high temperatures. To avoid burns or

other injuries, do not touch the pump, manifold or transfer tube while the unit is running.

Allow the parts to cool before handling or servicing. Keep children away from the

compressor at all times.

•

Risk to breathing. Read all labels when you are spraying paints or toxic materials, and

follow the safety instructions. Use a respirator mask if there is a chance of inhaling

anything you are spraying. Never directly inhale the compressed air produced by a

compressor.

•

Risk of eye injury. Always wear ANSI 287.1 approved safety goggles when using an air

compressor. Never point the nozzle or sprayer toward a person or any part of the body.

If the spray penetrates the skin, serious injury may occur.

•

Never exceed the maximum working pressure of the tool.•

Never attempt to open the drain valve when the tank pressure is more than 10 PSI.•

You can create dust when you cut, sand, drill or grind materials such as wood, paint,

metal, concrete, cement, or other masonry. This dust often contains chemicals known

to cause cancer, birth defects, or other reproductive harm. Wear protective gear.

•

Pull the pressure relief valve ring daily to ensure the valve is functioning properly.•

The unit must be kept a minimum of 12 in. from the nearest wall, in a well-ventilated area

for cooling.

•

Protect the air hose and electric cord from damage and puncture. Inspect them weekly for

weak or worn spots.

•

Always wear hearing protection when using an air compressor. Failure to do so may result

in hearing loss.

•

Operation of the unit should always be in a position that is stable. Never use the unit on

a rooftop or elevated position that could allow the unit to fall or be tipped over.

•

CAUTION

PREPARATION

Preparing for Startup

WARNING:Risk of bursting. Too much air pressure causes a hazardous risk of bursting.

Check the manufacturer’s maximum pressure rating for air tools and accessories.

The regulator outlet pressure must never exceed the maximum pressure rating.

a. Set the ON/OFF switch (I) to the off position.

b. Turn the air pressure regulator knob (D) counterclockwise until it stops.

c. Attach air hose/accessories or air tools (not included) to the quick coupler (F).

SAFETY INFORMATION

OFF

OPERATING INSTRUCTIONS

Starting up the Compressor1.

WARNING: High temperatures are generated by

the electric motor and the pump. To prevent

burns or other injuries, DO NOT touch the

compressor while it is running. Allow it to cool

before handling or servicing. Keep children

away from the compressor at all times.

WARNING: When adjusting from a higher to a

lower pressure, turn the knob counterclockwise

past the desired setting. Then turn clockwise to

reach the desired pressure. Do not exceed operating

pressure of the tool or accessory being used.

a. Close the tank drain valve (G) by turning clockwise.

b. Plug in the power cord (J).

c. Set the ON/OFF switch (I) to the on position

and allow tank pressure to build. Motor will stop when the tank reaches “cut-out” pressure.

d. Turn the air pressure regulator knob (D) clockwise until desired pressure is reached.

e. The compressor is ready for use.

WARNING: To avoid personal injury, always shut off and unplug the unit and relieve all air

pressure from the system before performing any service on the air compressor.

WARNING: Risk of unsafe operation. The unit cycles automatically when power is on. When

performing maintenance, you may be exposed to voltage sources, compressed air or moving

parts. Personal injuries can occur. Before performing any maintenance or repair, disconnect

the power source from the compressor and bleed off all air pressure.

CAUTION: Escaping air and moisture can propel debris that may cause eye injury. Wear

safety goggles when opening the drain valve.

a. Set the ON/OFF switch (I) to the off position.

b. Unplug the power cord (J).

c. Reduce the pressure in the tank through the outlet hose. Pulling the pressure relief valve

ring (H) and keeping it open will also reduce the pressure in the tank.

d. Tip the compressor so the tank drain valve (G) is at the bottom of the tank, then open the

tank drain valve counterclockwise to allow moisture to drain from the tank.

Shutting Down the Compressor

OPEN

OFF

CARE AND MAINTENANCE

WARNING: To avoid personal injury, always shut off and unplug the unit and relieve

all air pressure from the system before performing any service on the air compressor.

Regular maintenance will ensure trouble-free operation. The items listed here

should be inspected on a regular basis.

• On a daily basis, drain the tank to prevent corrosion from forming inside

the tank. Drain the condensation at the end of every day. Wear protective

goggles. Relieve the air pressure in the system and then open the drain

valve on the bottom of the tank.

• On a daily basis, pull the pressure relief valve to ensure that it is

operating properly and to clear the valve of any possible obstructions.

• Check all connections to ensure they are tight. A small leak from any part of the

compressor will reduce the unit’s performance. Spray a small amount of soapy water

around the area of the suspected leak with a spray bubble. If bubbles appear,

repair or replace the faulty component. Do not overtighten any connections.

• Before storing the unit for a long period, do the following:

• Use an air blow gun (not included) to clean all dust and debris from the compressor.

• Disconnect and coil the power cord.

• Pull the pressure relief valve to release all pressure from the tank.

• Drain all moisture from the tank.

• Cover the entire unit to protect it from moisture and dust.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

There is low

pressure, not

enough air, or the

compressor does not

stop.

1. The tank drain valve is open.

2. There is a leak in the

3. There is a prolonged or

excessive use of air.

4. The compressor is not large

enough.

5. There is a hole in the air hose.

6. The tank leaks.

7. The seals are blown.

8. The valve leaks.

9. There is a leaking or worn

piston.

1. Close the drain valve.

2. Check with soapy water.

Tighten or reseal leaking

DO NOT

OVERTIGHTEN.

with thread seal tape.

3. Decrease the amount of air used.

4. Check the air requirement of the

accessory. If it is higher than the

CFM and the pressure supplied by

the compressor, you need a larger

compressor. Most accessories are

rated at 25% of the actual CFM

while running continuously.

5. Check and replace if necessary.

6. WARNING: Replace the

compressor. DO NOT attempt to

repair.

7. Replace the compressor.

8 Replace the compressor.

9. Replace the compressor.

Air leaks from the

regulator or the

regulator does not

regulate air pressure.

1. The internal parts of the

regulator are dirty or damaged.

1. Replace the regulator or internal

parts.

The regulated

pressure gauge

reading drops when

airthe accessory is

being used.

1. This is normal.

2. The compressor is not large

enough.

1. If the pressure drops too low,

adjust the regulator while the

accessory is being used.

2. Check the air requirement of the

accessory. If it is higher than the

CFM and supplied by

the pressure

largera

the compressor, you need

are

compressor. Most accessories

rated at 25% of the actual CFM

while running continuously.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

The motor will not

run.

1. Tank pressure exceeds the

preset pressure switch limit.

2. The fuse is blown or the circuit

breaker tripped.

3. The check valve is stuck in the

open position.

4. The wire gauge in the cord is

wrong or the extension cord

length is excessive.

5. There are loose electrical

connections.

6. The motor’s thermal overload

protection has tripped.

7. The motor or capacitor is

defective.

1. The motor will start automatically

when the tank pressure drops

below the tank cut-in pressure.

2. Replace the blown fuse or reset

the circuit breaker. Do not use a

fuse or circuit breaker with a higher

circuit.

Check for proper fuse; type T fuse

is acceptable.

Check for low voltage and proper

extension cord size.

Disconnect other applications from

the circuit. Operate the compressor

on a dedicated circuit.

3. Remove and clean or replace.

4. Check for proper gauge (18 AWG)

and extension cord length (72 ft).

5. Contact customer service.

6. Turn the air compressor off, unplug

7. Have the compressor serviced by a

qualified technician.

the power cord and wait until the

motor has cooled down. Plug in

the power cord only after the motor

has cooled down, waiting

thermal overload protector has

the

recovered.

The pressure relief

valve opens.

1. The tank pressure exceeds the

normal rating pressure.

2. The pressure switch is stuck.

Replace the compressor.

2. Replace the compressor.

Table des matières

Langues :

Autres manuels Kobalt Compresseur d'air

Kobalt

Kobalt 215914 Manuel utilisateur

Kobalt

Kobalt 320541 Manuel utilisateur

Kobalt

Kobalt 215921 Manuel utilisateur

Kobalt

Kobalt 143075 Manuel de programmation

Kobalt

Kobalt 200-2614 Manuel utilisateur

Kobalt

Kobalt 143075 Manuel utilisateur

Kobalt

Kobalt K13015F Instructions d'installation et d'entretien

Kobalt

Kobalt TOPS - Thermal Overload Protection System Manuel utilisateur

Kobalt

Kobalt 241345 Manuel utilisateur

Kobalt

Kobalt Air compressor Manuel utilisateur

Kobalt

Kobalt 215914 Manuel utilisateur

Kobalt

Kobalt VT6389 Manuel utilisateur

Kobalt

Kobalt 99007 Manuel utilisateur

Kobalt

Kobalt 200382 Manuel utilisateur

Kobalt

Kobalt LK20175 Manuel utilisateur

Kobalt

Kobalt 215902 Manuel utilisateur

Kobalt

Kobalt 137603 Manuel utilisateur

Kobalt

Kobalt 138416 Manuel utilisateur

Kobalt

Kobalt TQ3126 Manuel utilisateur

Kobalt

Kobalt 200-2630 Manuel utilisateur

Kobalt

Kobalt 103797 Manuel utilisateur

Kobalt

Kobalt Air compressor Manuel utilisateur

Kobalt

Kobalt 200-2430 Manuel utilisateur

Kobalt

Kobalt 162700 Manuel de programmation

Manuels Compresseur d'air populaires d'autres marques

Sparmax

Sparmax DC-25XR Manuel utilisateur

KAESER

KAESER M122 Manuel utilisateur

GMC

GMC GAC1500 Manuel utilisateur

Briggs & Stratton

Briggs & Stratton Air Compressor Manuel utilisateur

Fini

Fini F3GST2TK Manuel utilisateur

Industrial Air

Industrial Air CP1580325 Manuel de programmation

Campbell Hausfeld

Campbell Hausfeld RP3300 Guide de démarrage rapide

Ingersoll-Rand

Ingersoll-Rand UP6 20 HP Manuel utilisateur

Hitachi

Hitachi EC99S Manuel de l'opérateur

Parkside

Parkside PKO 270 A1 Manuel utilisateur

Sullair

Sullair 185 Manuel utilisateur

Clas Ohlson

Clas Ohlson QIE-ZTH-15 Manuel utilisateur

Ferm

Ferm CRM1046 Manuel utilisateur

BE AC153 Manuel utilisateur

RIDGID

RIDGID OF25150A Manuel utilisateur

Johnson Controls

Johnson Controls QUANTUM LX Manuel

Sears

Sears Craftsman 919.167463 Manuel utilisateur

Ring Automotive

Ring Automotive RAC700 Manuel utilisateur