KNX Module LC-S.1 Manuel utilisateur

module-electronic.ru

KNX LINE COUPLER

LC-S.1

Application Program: ver. 1.0

User Manual: ver. 1.0

User Manual

CONTENT

Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1 Basic information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Speciﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3 Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Operational description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 TP coupler application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 TP repeater application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 KNX network installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.1 Individual addres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.2 KNX topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4.1 Programming button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.4.2 Individual address assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.5 Special function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.5.1 Manual function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.5.2 Factory reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.5.3 LED status display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 ETS database parameters coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.2 Main line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 Subline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

4 ETS database parameters repeater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.1 General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.2 Main line. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.3 Subline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

5 State of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.1 Default factory setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

page 2

module-electronic.ru

1 BASIC INFORMATION

The KNX line coupler provides a bi-directional data connection between two KNX TP lines or areas and

works as a KNX network. KNX TP main line and KNX TP subline are coupled having a galvanic isolation in

between.

• Various routing ﬁlter for group and individual telegrams

• Temporary disabling of routing ﬁlter via button

• Long telegrams with up to 240 bytes APDU length are supported

• LED status indication

• Galvanic isolation of connected lines

• Integrated ACK generator

• Power supply via KNX bus

• Low power consumption

• DIN rail 35mm mounting

LC-S.1

page 3

module-electronic.ru

1.1 SPECIFICATION

Device model

LC-S.1

KNX interfaces (Main, Sub)

Speciﬁcation

TP-256

Available application soware

ETS 4 and later

KNX connector

4-wire EIB connector (PUSH WIRE spring clips) for standard cable TP1 0,8мм Ø

KNX physical address by default

15.15.0

Power supply

via KNX bus: 21...30В DC

Consumption on the KNX bus (29V DC)

< 10mA

< 300mW

Operation temperature

-5°C ... + 45°C

Operation humidity

5 ... 95% (no condensation)

Degree of protection

IP 20, clean environment

Mounting type

DIN rail 35mm

Dimensions

36 х 90 х 71mm (2TE)

Weight

62 g

page 4

module-electronic.ru

1.2 APPEARANCE

90mm

36mm 71mm

A. Function button B. Programming button C. KNX TP main line connector D. KNX TP subline connector

1. LED bus state KNX TP (main line) 2. LED bus state KNX TP (subline) 3. LED telegram traﬀic KNX TP (main line)

4. LED telegram traﬀic KNX TP (subline) 5. LED group address routing 6. LED physical address routing

7. Programming LED

1. Bus state KNX TP (main line)

Green: Main line OK

Orange: Manual function active

2. Bus state KNX TP (subline)

Green: Subline OK

OFF: Subline not connected

3. Telegram traﬀic KNX TP (main line)

Green (blinking): Telegram traﬀic

Red (blinking): Transmission error

OFF: No telegram traﬀic

4. Telegram traﬀic KNX TP (subline)

Green (blinking): Telegram traﬀic

Red (blinking): Transmission error

OFF: No telegram traﬀic

5. Group address routing*

Green: Filter table active

Orange: Route all

Red: Block all

OFF: Routing of group telegrams is diﬀerent on main line and subline

6. Physical address routing

Green: Filter table active

Orange: Route all

Red: Block all

OFF: Routing of physical telegrams is diﬀerent on main line and subline

7. Programming

Red: Programming mode active

OFF: Programming mode not active

page 5

module-electronic.ru

KNX bus (Sub)

MAIN SUB

KNX bus (Main)

1.3 INSTALLATION AND CONNECTION

INSTALLATION

WIRING DIAGRAMS

Attaching to DIN rail

Removing from DIN rail

ATTENTION! Installation and connection of the device to the mains must only be carried

out by qualiﬁed personnel! Be sure to turn oﬀ the power before installing or removing the

device! Even when the device is turned oﬀ, the output terminals can be live! Do not

connect to the outputs a load that exceeds the recommended values! The design of the

device meets the requirements of electrical safety according to GOST 12.2.007.0-75.

page 6

module-electronic.ru

2 OPERATIONAL DESCRIPTION

In network installations LC-S.1 can be used as KNX TP area/line coupler or KNX TP line repeater. Aer

connecting the main line, LC-S.1 operates with its default settings. Setting the correct Individual Address

is necessary. Only Individual Addresses x.y.0 are allowed.

Figure 1. TP coupler application program

When LC-S.1 receives telegrams (for example during commissioning) that use Individual Addresses as

destination addresses, it compares the Individual Addresses of the receiver with its own Individual

Address and decides on that whether it has to route the telegrams or not.

When LC-S.1 receives telegrams that use group addresses as destination addresses, it reacts in

accordance with the parameter settings. During normal operation (with Group Telegram routing set to

ﬁlter), LC-S.1 only routes telegrams whose group addresses are entered in its ﬁlter table.

If a telegram is routed by LC-S.1 without receiving the corresponding acknowledgement, i.e. due to a

missing receiver or to a transmission error, the telegram will be repeated up to three times (depending on

the ETS setting). With the parameters «Repetitions if errors...», this function can be conﬁgured separately

for each line and both kinds of telegrams. It is recommended to use the default parameter setting.

If not already conﬁgured as «Line Coupler», the ETS application program «TP Coupler» has to be

downloaded to the device. Under the Information tab the conﬁguration setting can be changed by the

drop-down menu «Change Application Program». Aer changing the conﬁguration setting the ﬁlter table

entries can be added manually. Updating the application program version can also be done here.

2.1 TP COUPLER APPLICATION

page 7

module-electronic.ru

2.2 TP REPEATER APPLICATION

Any received telegram is routed to all lines irrespective of in which line it is processed. Line repeaters

make no use of a ﬁlter table. It is therefore not important whether the telegram is generated within a line

or whether it is sent from an upper line to a lower line via a coupler.

If a telegram is routed by LC-S.1 without receiving the corresponding acknowledgement, i.e. due to a

missing receiver or to a transmission error, the telegram will be repeated up to three times (depending on

the ETS setting). With the parameters «Repetitions if errors...», this function can be conﬁgured separately

for each line and both kinds of telegrams. It is recommended to use the default parameter setting.

If not already conﬁgured as Line/Area/BB Repeater, the ETS application program

«TP repeater» has to be downloaded to the device. Under the Information tab the conﬁguration setting

can be changed by the drop-down menu «Change Application Program». Aer changing the conﬁguration

setting the ﬁlter table entries can be added manually. Updating the application program version can also

be done here.

Figure 2. TP repeater application program

page 8

module-electronic.ru

2.3 KNX NETWORK INSTALLATION

For line coupler functionality in a KNX network LC-S.1 has to use the correct Individual Address of a line

coupler (x.y.0, 1≤ x & y ≤15). In ETS up to 225 addresses can be deﬁned (from 1.1.0 to 15.15.0).

For area coupler functionality in a KNX network LC-S.1 has to use the correct Individual Address of an area

coupler (x.0.0, 1≤ x ≤15). In ETS up to 15 areas can be deﬁned.

If LC-S.1 is used in a KNX system for both purposes, it is only necessary to ensure that the LC-S.1 used as a

line coupler has a line coupler address assigned from a free addressing area. Following ﬁgure illustrates

the LC-S.1 router topology for KNX lines and KNX areas.

2.3.1 INDIVIDUAL ADDRESS

Figure 3. LC-S.1 network

Example: If an area coupler with address 1.0.0 already exists on the backbone no line coupler with

address 1.x.0, 1≤ x ≤15 can be added here. Even if no line coupler with address 1.1.0 exists on

the subline of the 1.0.0 area coupler. Vice versa, if a line coupler with address 1.1.0 already

exists in the installation no area coupler with address 1.0.0 can be added.

page 9

module-electronic.ru

2.3.2 KNX TOPOLOGY

Via a line/area coupler up to 15 lines can be connected to a main line called an area. It is possible to have

up to 64 bus devices on one line. With use of line repeaters a line can theoretically be extended to 255 bus

devices. This means up to four line segments form a single KNX TP line. But it is common practice on

exceeding 64 bus devices to insert a new line instead of extending the originating one.

The free tree structure of the KNX topology prevents problems caused by circling telegrams and heavy

bus load. To maintain this condition, interconnection between lines or line segments is strictly forbidden.

Figure 4. LC-S.1 network topology

Each line segment requires its own KNX power supply unit.

Using repeaters on the backbone and main lines is not allowed.

Interconnections are not allowed.

page 10

module-electronic.ru

Table des matières

Autres manuels KNX Matériel réseau

KNX

KNX Module IC-IP-S.1.0 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur