Knoll WHD-HDMI Manuel utilisateur

Specifications:

Models and Dimensions

NOCAT-HDMI-T TRANSMITTER

6” X 3-3/4” X 1” HIGH (15 X 9.5 X 2.5 cm)

NOCAT-HDMI-R RECEIVER

6” X 3-3/4” X 1” HIGH (15 X 9.5 X 2.5 cm)

Power:

5 VDC 1500 mA on each transmit and receive.

Warranty:

Knoll Systems warrants its products sold in the USA and Canada by authorized

Knoll dealers to be free of defects in materials and workmanship. This warranty

extends for three full years from the date of purchase by the original consumer.

Any products returned to Knoll Systems and found to be defective by Knoll

Systems within the warranty period will be repaired or replaced at Knoll Systems

option, at no charge. Knoll Systems will not be responsible for the actual cost of

installation or removal of the product, nor for any incidental or consequential

damages. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation may not apply to you. This

warranty gives you specific legal rights. You may have additional legal rights

that vary from state to state.

Knoll Systems www.knollsystems.com

145 Tyee Drive Point Roberts, WA 98281

12140 Horseshoe Way, Richmond BC V7A 4V5

Tel. (604) 272 4555, fax (604) 272 5595

WHD-HDMI

WIRELESS SYSTEM

Installation Instructions

v1.0

Warning: To be installed and/or used in accordance with

appropriate electrical codes and regulations. If you are not sure

about any part of these instructions, consult a qualified

electrician.

Introduction: Thank you for your purchase of a Knoll HDMI

wireless system. This system will take any HDMI signal and

transmit it to its receiver which can be up to 30 meters (about

100 feet) away in ideal conditions, even through walls.

Please note that this wireless system may not work well or not

at all in certain environments that have high electro-magnetic

interference at times. Suitability for use should always be tested

when possible.

Features:

Working frequency range: 2.4 GHz and 4.9 to 5.9 GHz

Supports video resolution: 480p, 576p, 720p, 1,080p

Supports HDMI® video audio format and HDCP 1.2 with

video encryption

Supporting link speeds: up to 2.5 Gbps per channel

Certification: 802.11a/n

Omni-directional antennas

Up to 30 meters transmit distance with ultra low latency

Infrared remote control pass through

Wiring:

Gently connect your HDMI source with a short as possible (less

than 10 meters or 30 feet) HDMI wire to the Transmitter.

Connect the Receiver to the TV, display or monitor with a

second short as possible HDMI wire. Make sure the HDMI wires

are top quality. If required connect the infrared emitter on the

Transmitter and place the emitter on the source component

needing control.

Power Supply Connection:

After connecting the HDMI wires, insert the 5 volt plug on each

of the supplied power supply to the Transmitter and Receiver.

Next plug the AC side of the power supply into wall outlets or if

possible the switched outlet on the source component. There is

no on/off switch.

LED Indicators:

Both the Transmitter and Receiver each have three front panel

LED’s. The red LED indicates that the units are powered up

correctly. The green on the right indicates when the units are

ready to receive or transmit. The middle green LED is on (not

blinking) when a good quality synced signal is going though its

processors.

Troubleshooting:

If the NOCAT-HDMI system does not appear to be functioning,

make certain the source and the destination devices connected

are functioning and turn on. Reconnect the devices using

maximum 3 meter (10 foot) long cables (in other words make

sure the problem is not long cables in which case a HDMI balun

may be required). If the signal is present then make sure both

the Transmitter and Receiver are getting power. If it still does

not work, carefully inspect the cables and connectors for any

damage. If the system is still not working the Transmitter and

Receiver may be too far apart. Try moving them closer.

If the Receiver picks up some interference it may result in a

poorer quality video or a buzz in the sound. If this persists try

unplugging the Receiver and plugging it back in to reset its

interference protection.

This product can get very warm when operating. This is normal.

Non HDCP Compliant Devices:

If a destination device does not appear to work, make certain

that the device is HDCP compliant. A non-HDCP compliant

device will not work with a signal that has HDCP encoding

present.

If problems are experienced with this product, please call our

tech line for help at 1 800 566 5579.

Figure 1: Sample setup

HDMI-INIR-OUT DC 5V HDMI-OU T DC 5V

DVD

TRANS MITTER RECEIVER

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Knoll Système de microphone

Knoll

Knoll WHD3 Manuel utilisateur

Manuels Système de microphone populaires d'autres marques

Paso

Paso R824 Manuel utilisateur

Naxa

Naxa NAM-982 Manuel utilisateur

Motorola

Motorola PMNN4461 Manuel utilisateur

Xvive

Xvive U3 Manuel utilisateur

Tekon

Tekon DUOS Manuel utilisateur

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuel utilisateur

Devine

Devine WMD-IE Manuel utilisateur

LG LF-D7150 Manuel utilisateur

GE S768DAV Manuel utilisateur

LD U305 HBH 2 Manuel utilisateur

Chainway

Chainway URA8 Manuel utilisateur

ORATOR

ORATOR D860TD Manuel utilisateur

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuel utilisateur

Alpha Technologies

Alpha Technologies RBMS Manuel utilisateur

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuel utilisateur

Shure

Shure UA844 Manuel utilisateur

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuel utilisateur

Pyle

Pyle PDWM5000 Manuel utilisateur