KNF FL 10 Manuel utilisateur

FL 10

INSTALLATION INSTRUCTIONS

DIAPHRAGM PUMP

FL 10 DC-P FL 10 AC

Before operating the pump, please read the Installation Instructions and safety precautions.

Table of Contents

KNF Flodos 173856_MA_FL10_EN_01.docx

Contents Page

1 General ...................................................................................... 3

1.1 Information about the instructions 3

1.2 Warnings 3

1.3 Disclaimer 4

1.4 Manufacturer’s address 4

1.5 Supporting documents 4

2 Safety ........................................................................................ 5

2.1 Intended use 5

2.2 Reasonably foreseeable misuse 5

2.3 Responsibility of the user 5

2.4 Product-specific risks 5

3 Installation ................................................................................ 7

3.1 Installation location 7

3.2 Mechanical mounting 7

3.3 Connecting the fluid system 7

3.4 Electrical connection 8

4 Initial start-up ........................................................................... 9

5 Maintenance ........................................................................... 10

6 Rectifying transfer problems ................................................ 10

7 Returning the pump ............................................................... 11

Installation Instructions FL 10 General

KNF Flodos 173856_MA_FL10_EN_01.docx1

1 General

1.1 Information about the instructions

The Installation Instructions describe the requirements for installing

the product correctly and safely into the complete machine.

These Installation Instructions are a part of the product. The safety-

relevant information should be taken over for the documentation of

the complete machine.

With customer-specific project pumps (pump types which begin

with "PL" or "PML"), there may be differences from the Installation

Instructions.

1.2 Warnings

Warnings in the Installation Instructions are marked by the hazard

symbol, the keywords, and the color. These features provide

information about the extent of the hazard.

DANGER

Indicates a dangerous situation, which will directly cause death or

serious injury if not prevented.

WARNING

Indicates a dangerous situation, which may cause death or seri-

ous injury if not prevented.

CAUTION

Indicates a dangerous situation, which may cause moderate or

slight injuries if not prevented.

NOTICE

Indicates a situation, which may cause damage to property if not

prevented.

Table of Contents

Storage location

Project pumps

General Installation Instructions FL 10

KNF Flodos 173856_MA_FL10_EN_01.docx1

1.3 Disclaimer

The manufacturer accepts no liability for damage or malfunctions

that are caused by non-compliance with the Installation Instruc-

tions.

The manufacturer accepts no liability for damage or malfunctions

that are caused by modifications to or conversions of the device or

by improper handling.

The manufacturer accepts no liability for damage or malfunctions

that are caused by using spare parts or accessories that are not

approved by the manufacturer.

1.4 Manufacturer’s address

KNF Flodos AG

Wassermatte 2

6210 Sursee, Switzerland

Phone +41 (0)41 925 00 25

Fax +41 (0)41 925 00 35

www.knf.com

1.5 Supporting documents

The listed documents must also be observed. The valid versions

are available on www.knf.com/downloads.

 Data sheet

 3D model

Further attention must be paid to:

 Local T&Cs

 Sales documents and agreement between KNF and the cus-

tomer

Installation Instructions FL 10 Safety

KNF Flodos 173856_MA_FL10_EN_01.docx1

2 Safety

2.1 Intended use

The pump is intended solely for the following uses:

 Transferring liquids and gases

 For operation in accordance with the operating parameters

specified in the technical data of the supporting documents

2.2 Reasonably foreseeable misuse

The pump must not:

 be operated in an explosive atmosphere

 be used to transfer explosive media

 be used to transfer media whose compatibility with the pump

head, valves, diaphragms, and seals has not been proven

2.3 Responsibility of the user

The user is responsible for ensuring that the safety precautions in

these Installation Instructions are complied with. Applicable, safety,

accident prevention, and environmental protection regulations must

be complied with.

2.4 Product-specific risks

Remaining risks that were determined in a risk assessment are

described in this section. Safety precautions and warnings in this

section and in the other sections of the Installation Instructions

must be observed to prevent dangerous situations.

DANGER

Danger of injuries and damage to property due to dangerous

substances

Poisoning and chemical burns or unintended reactions caused by

leaking dangerous substances

 Observe the safety data sheets of the transferred media

 Before transferring a medium, check whether it can be

transferred safely in the specific application case.

 Ensure that the system is not subject to any risks of explo-

sion, also in extreme operating conditions (temperature,

pressure) or in case of malfunctions.

 Ensure the pump is used only by suitably trained, skilled

employees

 Clarify the wear resistance of the head material

 Check that the pump and the system do not leak at the op-

erating temperature of the transferred medium

 Regularly check the pump for damage

 Operate the pump only when you are sure it has no tech-

nical malfunctions

 Operate the pump in accordance with the technical data

 Work on the pump or fluid circulation system only after they

have been decontaminated and/or a decontamination decla-

ration is present

Safety Installation Instructions FL 10

KNF Flodos 173856_MA_FL10_EN_01.docx1

DANGER

Danger of injuries and damage to property due to leaks at the

interfaces to the pump head

Poisoning and chemical burns or unintended reactions caused by

leaking dangerous substances

 Wear personal protective equipment

 Connect the pump correctly

 Operate the pump only when you are sure it has no tech-

nical malfunctions

 Operate the pump in accordance with the technical data

DANGER

Danger of injuries and damage to property due to uncon-

trolled flow while the pump is not in operation

Poisoning and chemical burns or unintended reactions caused by

leaking dangerous substances

 Install a shut-off valve in the fluid circulation system

WARNING

Danger from magnetic field

The pump generates a strong local magnetic field, which may

cause pacemakers or other devices that are affected by magnetic

fields to malfunction.

 Ensure that these devices are kept at least 10 cm away

from the pump when it is operating

 If necessary, attach additional shielding devices

Installation Instructions FL 10 Installation

KNF Flodos 173856_MA_FL10_EN_01.docx1

3 Installation

WARNING

Danger from incorrect installation

Injuries or damage to property from leaking media

 After installation, check the system for leaks with a safe

medium

 Observe the requirements for intended use

 Take precautions in the design of the end device so that

leaking liquids cannot come into contact with live compo-

nents

The following requirements apply to all activities described in this

section:

3.1 Installation location

The installation location must:

 protect the pump against immersion

 keep aggressive and flammable liquids and vapors away

 allow hoses to be connected without tensile or bending stress

 take account of cooling the pump drive

 ensure that any leaks can be handled

 have appropriate precautions if flammable media are used

3.2 Mechanical mounting

 Protect the product against impacts, knocks, and strong vibra-

tions

 For dimensions, installation positions, fluid connections, please

refer to the product data sheet

3.3 Connecting the fluid system

Use suitable means to check the fluid connection for leaks.

For more information regarding dimensions, please refer to the

data sheet.

Installation Installation Instructions FL 10

KNF Flodos 173856_MA_FL10_EN_01.docx1

3.4 Electrical connection

For terminal assignment, output data, and control requirements,

please refer to the data sheet

Observe the regulatory requirements for electrical installations:

 Overload protection and separating protective devices

 Contact protection and additional insulation

 Ground connections

 Protection against vibrations, tensile stress, and corrosion

3.4.1 DC coils

CAUTION

Danger from burns or fire, poisoning from flue gases

If the pump is connected incorrectly, it may overheat and catch

fire.

 Connect the pump to the correct voltage

 Operate the pump in accordance with the technical data

 Take suitable precautions to limit maximum power con-

sumption.

3.4.2 AC coils

DANGER

Danger from electric shock

 Connect the pump to the correct voltage

 Wear personal protective equipment

 Operate the pump only when you are sure it has no tech-

nical malfunctions

 Operate the pump in accordance with the technical data

 Ensure that the fluid circulation system is grounded

 Check the pump for damage regularly

 Disconnect the pump from the power supply when carrying

out maintenance work

 In case of fixed installation, install a maintenance switch

 Installation only by trained, skilled personnel who have

knowledge of the applicable international regulations

 Ensure contact protection for live parts (persons, cable, and

device protection)

Installation Instructions FL 10 Initial start-up

KNF Flodos 173856_MA_FL10_EN_01.docx1

4 Initial start-up

The product must not be started up until it has been ensured that

the machine in which the product is to be installed meets the

requirements of the Machinery Directive 2006/42/EC, if applicable.

CAUTION

Danger of bursting of the fluid system due to overpressure.

The pump builds up pressure. With a closed system, the max.

permitted operating pressure may be exceeded, which can dam-

age the pump and the system.

 Prevent operation against a closed system

 Use only parts that come into contact with the fluid that are

designed to at least withstand the operating pressure of

the pump

 If necessary, take suitable measures to limit the maximum

system pressure

CAUTION

Danger of unexpected chemical reactions with water

Residues of water in the pump that come from testing in the

factory may react with the transferred medium.

 Before starting the pump for the first time, rinse it with a

medium that is uncritical as regards water

CAUTION

Danger from hot surfaces

The pump becomes hot during operation Burns from hot surfaces

or injuries from uncontrolled movements are possible.

 Do not touch the pump while it is operating.

 Ensure a sufficient supply of cool air and keep a safe dis-

tance between the pump and neighboring components.

 Operate the pump in accordance with the technical data

 If the temperature of the medium is above 50°C, take pre-

cautions to prevent burns from fluid components.

Before switching on the pump, check the following points:

 All hoses attached properly

 Specifications of the power supply correspond with the data on

the pump’s type plate

 Pump discharge not blocked

 All cables attached properly

 Contact protection for electrical connections and moving parts

installed

Maintenance Installation Instructions FL 10

KNF Flodos 173856_MA_FL10_EN_01.docx1

5 Maintenance

This product contains no parts that can be replaced and it cannot

be maintained.

6 Rectifying transfer problems

Symptom Cause Remedy

Pump does not work,

no movement or

sounds detectable

No or incorrect control Check that voltage and signal form comply

with the specification

Pump does not work,

drive is very hot

The coil is controlled with

DC voltage or another,

incorrect signal form

Check that voltage and signal form comply

with the specification

The pump does not

suck or vacuum is

insufficient

External valve is closed Check external valve

Counter pressure on

pressure side is too high

Change the pressure conditions on the

pressure side

Particles in the pump head

Rinse the pump head

Use a preventive preliminary filter

Pump does not trans-

fer

External valve is closed or

filter is clogged or too

small

Check external valves and filter

Connections or hoses are

blocked

Check connections and hoses

Remove blockage.

Flow rate is insuffi-

cient or unstable

Incorrect control Check that voltage and signal form comply

with the specification

Cross-section of hydraulic

hoses or connectors too

narrow or restricted

Disconnect the pump from the system and

determine output values

Remove restriction (e.g. valve) if neces-

sary.

If applicable, use larger-diameter hoses or

connectors

Higher counter pressure in

the system than assumed

for the design

Contact KNF representative

Particles in the pump head

Rinse the pump head

Use a preventive preliminary filter

Pump has reached the

end of its service life

Replace the pump

Leak of pump head Diaphragm or oscillating

diaphragm defective

Replace the pump

If the malfunction cannot be rectified, contact your local KNF

representative (www.knf.com)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KNF Pompe à eau

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur