KMC Controls STE-9000 Series NetSensor Manuel utilisateur

KMC Controls, 19476 Industrial Drive, New Paris, IN 46553 /877.444.5622 /Fax: 574.831.5252 /www.kmccontrols.com

STE-9000 Series NetSensor

Installation Guide

REMOVE BACKPLATE

1. Turn the hex screw 1clockwise into the

sensor until the screw clears the cover.

NOTE: The hex screw 2should remain in the

backplate.

2. Pull the cover off the backplate.

CONNECT ETHERNET CABLE

3. Feed the Ethernet patch cable 3from the

Conquest controller through the center of the

backplate 4.

NOTE: The Ethernet patch cable should be a

maximum of 150 feet (45 meters).

Complete the following steps to mount a KMC

Conquest STE-9000 Series Digital NetSensor

and connect it to a Conquest BAC-59xx/9xxx

Controller.

STE-90xx/93xx STE-92xx/95xx

with Motion Sensor

NOTE: See the Conquest NetSensors STE-

9000 Series Digital Room Sensors

data sheet and the Conquest Selection

Guide at kmccontrols.com for

specications and other information.

NOTICE

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE DEVICES

SELECT MOUNTING LOCATION

See the Room Sensor and Thermostat Mounting

Location and Maintenance Application Guide for

cautions, troubleshooting, and best practices.

NOTE: Complete rough-in-wiring at each

location before installing a sensor.

7. Turn the hex screw 9counterclockwise until

it engages the cover.

OPERATE

The STE-9000 Series NetSensor becomes

operational after it is connected to a powered

Conquest controller.

NOTE: To change setpoints or conguration,

see the KMC Conquest Controller

Application Guide.

NOTE: For continued maximum NetSensor

efciency, see the maintenance section

in the Room Sensor and Thermostat

Mounting Location and Maintenance

Application Guide.

4. Mount the backplate on an electrical box using

the provided screws.

NOTE: If additional thermal insulation is

needed, install the optional HPO-9002

gasket before installing the backplate.

For more information, see the Room

Sensor and Thermostat Mounting

Location and Maintenance

Application Guide.

5. Plug the Ethernet cable 5into the modular

jack 6of the sensor.

INSTALL SENSOR COVER

6. Place the cover 7over the top of the

backplate 8and swing it down.

NOTE: Be careful not to pinch the Ethernet

cable.

IMPORTANT NOTICES

The material in this document is for information

purposes only. The contents and the product it

describes are subject to change without notice.

KMC Controls, Inc. makes no representations or

warranties with respect to this document. In no

event shall KMC Controls, Inc. be liable for any

damages, direct, or incidental, arising out of or

Manuels Régulateurs de température populaires d'autres marques

Swegon

Swegon LUNAd MB Manuel utilisateur

Lucky Reptile

Lucky Reptile Thermo Control II Manuel utilisateur

SENSORMETRIX

SENSORMETRIX Argon 100 Manuel utilisateur

Fuji Electric

Fuji Electric PXE4 Manuel utilisateur

Yuyao gongyi

Yuyao gongyi XMT-808 series Manuel utilisateur

Selec

Selec TC544C Manuel utilisateur

P.W. KEY

P.W. KEY rt-208gt Manuel utilisateur

Future Design

Future Design FDC-9200 Manuel utilisateur

BH Thermal

BH Thermal BriskONE Manuel utilisateur

Omron

Omron E5EX-H Manuel utilisateur

West Control Solutions

West Control Solutions KS 45 Guide de démarrage rapide

MCS

MCS RITC-15B Manuel utilisateur

SMC Networks

SMC Networks Thermo-con INR-244-639 Manuel utilisateur

eltherm

eltherm Ex-TC It Series Manuel utilisateur

Omron

Omron C200H-TV Series Manuel utilisateur

industrie technik

industrie technik CA1 Manuel utilisateur

KRAL

KRAL EET 32 Manuel utilisateur

dixell

dixell XR420C Schéma de câblage