ENGLISH
READ ALL INSTRUCTIONS BEFORE OPERATING AND RETAIN
INSTRUCTIONS FOR FUTURE REFERENCE
TURNING DIGITAL PROBE-PRO AND WORKLIGHT ON/OFF
Turn the probe on by pressing the Power On/Off Button
When the probe is on, press the Power On/Off Button
Turn the probe on by pressing the Power On/Off Button
to turn the worklight on/off.
to turn the worklight on/off.
To turn off the probe, press and hold the Power On/Off Button
to turn the worklight on/off.
Turn Digital Toner-Pro on by pressing the Power On/Off button
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
LEDs 3 and 6 illuminated. The LEDs may be
LEDs 3 and 6 illuminated. The LEDs may be
blinking, depending on whether the Toner is connected to a network port.
Set the tone mode to either digital toning or analog toning by pressing
the Digital/Analog Tone Button
Set the tone mode to either digital toning or analog toning by pressing
to cycle thru the different options. The
the Digital/Analog Tone Button
, will illuminate when in digital toning mode.
One or both Analog Tone Frequency Indicators
, will illuminate when in digital toning mode.
analog toning mode. There are three frequencies available to choose from
when in analog mode: 1000Hz, 1500Hz, and 1000/1500Hz warble.
When performing analog toning via the RJ45 port, the tone can be sent
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
down an individual pin, a pin pair, or to all eight pins simultaneously. To cycle
to select the desired mode. The Wire Map Indicator
thru the analog tone options, repeatedly press the Pin/Pair Selector Button
will illuminate which pin
or pin pairs will be toned. When performing digital toning via the RJ45 port, the
signal is only sent to pin pair 3-6. Wire Map Indicator LEDs 3 and 6 will blink if
toner is connected to an active network port, otherwise LEDs 3 and 6 will remain
TRACING PAIRED WIRES (FIG. 1)
nnect the Digital Toner-Pro’s red
ABN Test Clip leads to their
ABN Test Clip leads to their
respective Test Lead Inputs
nnect the Digital Toner-Pro’s red
Connect the red ABN Test Clip
to one of the wires of the pair to be traced.
Connect the black ABN Test Clip
Connect the red ABN Test Clip
Connect the black ABN Test Clip
Connect the red ABN Test Clip
Connect the black ABN Test Clip
to one of the wires of the pair to be traced.
to the other wire to be traced.
to the other wire to be traced.
Turn Digital Toner-Pro on by pressing the Power On/Off button
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
The Toner defaults to Digital Tone Mode, with the Digital Tone Indicator
LEDs 3 and 6 illuminated. The LEDs
LEDs 3 and 6 illuminated. The LEDs
may be blinking, depending on whether the Toner is connected to
When performing analog toning, check the "CONT"
. If illuminated green, you may proceed.
When performing Digital Toning, the "CONT" Indicator
Select the preferred tone setting using the Digital/Analog Tone Button
Turn the Digital Probe-Pro on by pressing the Power On/Off button
At the far end of the cable, spread the wires apart at least 2" (51 mm), if possible.
If performing analog toning, first ensure the Digital Toner-Pro is set to analog
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
pressing the Analog Mode button
toning mode. Then ensure the Digital Probe-Pro is set to analog mode by
. The Analog Mode Button will illuminate
green when in analog mode. If performing digital toning, first ensure the
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Pro is set to digital mode by pressing the Digital Mode Button
Digital Toner-Pro is set to digital toning mode. Then ensure the Digital Probe-
Mode Button will illuminate blue when in digital mode.
Use the Digital Probe-Pro to scan the cable’s wire pairs. Move the Digital Probe-
Use the Digital Probe-Pro to scan the cable’s wire pairs. Move the Digital Probe-
slowly across the wires (FIG. 1). The Digital Probe-Pro’s volume and
slowly across the wires (FIG. 1). The Digital Probe-Pro’s volume and
Signal Strength Indicator bars
slowly across the wires (FIG. 1). The Digital Probe-Pro’s volume and
slowly across the wires (FIG. 1). The Digital Probe-Pro’s volume and
will increase as it approaches the toned
will increase as it approaches the toned
pair. When the Digital Probe-Pro’s volume and Signal Strength Indicator bars
are high over the first wire, low in the middle (between) the two wires, and high
over the second wire, you have located the pair of wires you are tracing. Use the
over the second wire, you have located the pair of wires you are tracing. Use the
over the second wire, you have located the pair of wires you are tracing. Use the
buttons to adjust the volume.
buttons to adjust the volume.
