Kitsound HIVE X Manuel utilisateur
JB. 5910-a / Made in China. © KitSound is a trademark of Kondor Limited, 2017. Christchurch, Dorset, BH23 4FL, UK
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such
marks by Kondor Ltd. is under license. Other trademarks and trade names are those of their respective owners.
All trademarks are acknowledged as the property of their respective owners. Unless otherwise stated their use does not
imply that the trademark owner is aliated with KitSound or endorses the products herein.
Please recycle this packaging responsibly.
kitsound.co.uk
USER MANUAL
HIVE X
BLUETOOTH®
SPEAKER
2 3
Please read this manual carefully before use.
Box contents
• KS Hive X Bluetooth Speaker
• 3.5mm Aux cable
• Micro USB charge cable
• User manual
Functions
1. TWS button
2. MFB (Multi-function button)
3. Volume–/Previous track
4. Volume+/Next track
5. Power button
6. LED indicator
7. Battery LED
8. Microphone
9. NFC
10. Aux-in port
11. Micro USB charging port
12. USB output
KS Hive X is IPX6 waterproof
The speaker is rated IPX6. This means it protects from water jets at any direction, but is not
impervious to large amounts of water. Please do not directly immerse in water.
• To ensure that the KS Hive X speaker is waterproof, please remove all cable connections and tightly
close the cap; exposing the KS Hive X speaker to liquids without doing so may result in permanent
damage to the speaker
• Do not expose the KS Hive X speaker to water while charging; this is very dangerous as doing so
may result in personal injury and permanent damage to the speaker or power source
• IPX6 waterproof is dened as the protected against high-pressure jet spray from all directions and
temporary ooding
Instructions for use
Charging the battery
Give the speaker a full charge before its rst use.
1. Connect the USB charging cable to the Micro USB charging port (11) and plug into power
2. The Battery LED (7) will be solid red whilst charging which will take up to 6 hours
3. Once fully charged the Battery LED (7) will turn o
Note: Allow up to 8 hours for the rst charge. You can charge and play your speaker at the same time,
but it needs extra charging time.
10
12
11
86
7
1 32 4 5 9
4 5
Battery protection mode
If you haven’t used the speaker for 90 days, the speaker will switch to battery protection mode automatically.
To keep the rechargeable battery in good condition, please discharge and recharge speaker every
3 months, even if you use it or not.
Note: For best sound quality when the battery is below 30%, it is best to charge the Hive X.
LED lights indication
Pairing mode Flash blue quickly for new device pairing
Flash blue slowly for auto reconnection to last paired device
Paired in Bluetooth®mode Solid blue
Paired but not playing audio Flash blue every 2 seconds
Aux-in mode Solid red
TWS pairing Flash blue and red quickly
Enter TWS mode Flash blue and red every 2 seconds
TWS paired with device Slow ashing purple
TWS paired with device and
playing audio
Solid purple
Battery below 30% Flash red every 3 seconds
Charging battery Red LED on
Charging nish (around 95%) Red LED o
Pairing the Hive X to your device
1. Long press Power button (5) to turn the speaker on and it will automatically enter pairing mode
2. Turn your iOS, Android, or Windows device’s Bluetooth ON and search for new devices
3. Select ‘KS Hive X’. If asked for a passcode, enter ‘0000’, and the device will pair
4. Once connected the LED indicator (6) will be a solid blue if playing audio or slowly ashing blue
if not playing audio
Re-pairing or pairing new devices
1. Turn Bluetooth connectivity o on any previously paired devices
OR
2. Long press the MFB (2) to re-enter pairing mode
3. Follow the ‘Pairing the Hive X to your device’ instructions
Note: If a previously paired device is not present within the Bluetooth connectivity range then
the speaker will re-enter pairing mode.
6 7
Auxiliary
1. Plug the Aux cable into the speaker’s Aux-in port (10) and your device
2. The LED indicator (6) will become a solid red colour
Once connected to the Hive X either wired or by Bluetooth, please follow the below instructions:
Function Bluetooth mode Auxiliary mode
Volume+ Short press Volume+ (4) on Hive X
or use your device
Short press or hold Volume+(4)
on Hive X or use your device
Volume– Short press Volume– (3) on Hive X
or use your device
Short press or hold Volume– (3)
on Hive X or use your device
Next Track Hold Volume+ (4) button for
2 seconds
N/A
Previous Track Hold Volume– (3) button for
2 seconds
N/A
Play/Pause Track Short press MFB (2) Short press MFB (2)
Answer Call Short press MFB (2) N/A
End Call Short press MFB (2) N/A
Reject Call Double press MFB (2) N/A
Redial Double press MFB (2) N/A
Pair with NFC
1. On your device make sure both the NFC and Bluetooth functions are switched on
2. With the Hive X powered on and not connected to another device, place your device over the
NFC (9) icon and your device will automatically pair to the speaker
3. A prompt might appear saying ‘Pair to KS Hive X’
4. Select ‘Pair’ and the Hive X will then be paired to your device
5. A double beep will sound to conrm pairing and the LED indicator (6) will ash every 2 seconds
Playing music on your speaker
Bluetooth
When connected via Bluetooth, play music on your device and the sound will play through the speaker.
Some devices may require you to select the audio output.
8 9
TWS for stereo sound
1. With both speakers turned on and in pairing mode, short press TWS button (1) on one speaker
(Master) and the LED indicator (6) will quickly ash red and blue
2. The Master speaker will automatically nd the other speaker
3. Once connected the LED indicator (6) will slowly ash purple on both speakers
4. Turn your iOS, Android, or Windows device’s Bluetooth ON and search for new devices
5. Select ‘KS Hive X’. If asked for a passcode, enter ‘0000’, and the device will pair
6. Once connected, the LED indicator (6) will be a solid purple if playing audio or slowly
ashing purple if not playing audio
Note: To cancel the TWS on both, long press TWS button (1) and they will disconnect and re-enter
pairing mode.
USB output
You can charge your device via the USB output (12), the output voltage and current is 5 V / 1 A.
• Please do not use the USB output (12) when the battery of KS Hive X is below 30% (when the Battery
LED (7) is ashing red every 3 seconds)
• It’s not available to use when powered o
Please note: Your device will have an internal amplier and if it is playing digital les like MP3s it will also
have an integrated DAC (Digital Audio Converter). If you turn the volume up to 100%, your device will be
sending a distorted signal. To avoid this, and to get the best quality from the speaker, we recommend
that you do not run your device any higher than 95% volume. Some devices output higher than others,
so you may need to reduce the volume if you experience distortion.
Care for your Hive X
Please DON’T:
• Submerge the Hive X speaker in water or spray water for over 3 minutes
• Drop the Hive X as this will invalidate your warranty.
• Open up the Hive X. There are no user serviceable parts inside
• Expose the Hive X to extreme temperatures or rapid changes of hot to cold or vice versa
Please DO:
• Clean the Hive X with a soft dry cloth and no detergents
10
Troubleshooting
We hope you’ve now got all the information you need to get started, but if you’re having problems
Hereby, Kondor Ltd declares that the radio equipment type,
KSHIVEXBK Hive X Wireless Speaker, is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address: http://kondor.co.uk/product-documents.’
The use and operation of this speaker is beyond our control. Warranty of the KS Hive X is limited to defects caused by faulty manufacture
or defects in materials only. No warranty whatsoever is given or implied for damage caused by the user under any circumstances.
This does not aect your statutory rights.
Please do not attempt to open this product. There are no user serviceable parts inside, in particular if your product has an embedded,
non-replaceable battery, do not attempt to access or remove the battery as this may cause personal injury and will damage the product.
Making any attempt to open the product or carry out repair voids any and all warranties.
We apologise for any inconvenience caused by minor inconsistencies in these instructions, which may occur as a result of product
improvement and development.
Specications
Works with Bluetooth®V4.2
Bluetooth connectivity distance up to 15 m
S/N 80 dB
Frequency response 60 Hz – 20 kHz
Drivers 2 x 57 mm
Output RMS 2 x 10 W
Battery rechargeable Li-ion, 3300 mAh, 5 V
Play time up to 20 hours
USB charge output 5 V @ 1 A
Charging time up to 6 hours
IP ratings IPX6
Dimensions (mm) H83 x W210 x D70
Weight 0.85 kg
Table des matières
Autres manuels Kitsound Intervenants
Kitsound
Kitsound HAWAII 1.0 Manuel utilisateur
Kitsound
Kitsound SOUL 2 Manuel utilisateur
Kitsound
Kitsound Glow Stereo Manuel utilisateur
Kitsound
Kitsound MINI MOVER 20 Manuel utilisateur
Kitsound
Kitsound OVATION Manuel utilisateur
Kitsound
Kitsound BoomBar+ Manuel utilisateur
Kitsound
Kitsound UPSTAGE Manuel utilisateur
Kitsound
Kitsound REUNION Manuel utilisateur
Kitsound
Kitsound VOICE ONE Manuel utilisateur
Kitsound
Kitsound CADET Manuel utilisateur
Kitsound
Kitsound Hive 2 Manuel utilisateur
Kitsound
Kitsound CUBE Manuel utilisateur
Kitsound
Kitsound SLAM Manuel utilisateur
Kitsound
Kitsound SLAM 2 Manuel utilisateur
Kitsound
Kitsound Podium Manuel utilisateur
Kitsound
Kitsound FLAIR Manuel utilisateur
Kitsound
Kitsound BOOMBAR 2 Manuel utilisateur
Kitsound
Kitsound POCKETBOOM Manuel utilisateur
Kitsound
Kitsound IGNITE Manuel utilisateur
Kitsound
Kitsound POCKETBOOM XB Manuel utilisateur
Manuels Intervenants populaires d'autres marques
Bowers & Wilkins
Bowers & Wilkins 4 Manuel utilisateur
Sonance
Sonance SONOS OUTDOOR Series Manuel utilisateur
Electro-Voice
Electro-Voice EVID FM4.2 Manuel utilisateur
Pioneer
Pioneer XW-HTD630 Manuel utilisateur
Onn
Onn BWA16AA002 Manuel utilisateur
HP
HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur