Kisai Blade Manuel utilisateur
Button
A
USB Port
Button
B
INSTRUCTION MANUAL
Blade has 2 time display modes [TURNING] & [FLASHING]
The default setting is [TURNING]
To change the time display mode, see section 4 “How to set the
time & display modes”.
Press button A to show the time.
Examples:
[12] [5] [9] = 12:59 [6] [3] [5] = 6:35 [10] [0] [8] = 10:08
In the image below the line at 3 o’clock is lit, indicating 3
The display will light up an blade which rotates around the face
3 times.
Each time it rotates it leaves 1 line lit, indicating in turn:
[hour] [group of 10 mins] [single mins]
This is known as the 12-5-9 method of time telling.
1. How to read the time
•
•
•
•
I. Turning Mode
Turning Mode - Full Example
Blade rotates
Blade rotates
Blade rotates
4 o’clock
20 minutes
7 minutes
First Spin
After pressing button A the blade rotates,
leaving the 4 o’clock line lit.
It is 4 o’clock.
Second Spin
On the second rotation the blade leaves the 2
o’clock line lit, indicating 20 minutes.
It is 4:20
Third Spin
On the third rotation the blade leaves the 7
o’clock line lit, indicating 7 minutes.
It is 4:27 exactly
Note:
If the blade rotates without leaving any line lit, it indicates ZERO
6 o’clock 10 o’clock
Time: 6:45 Time: 10:18
Time: 1:07
45 minutes
(flashing)
15 minutes
(flashing)
+3 minutes
(dots)
+2 minutes
(dots)
1 o’clock
(flashing rapidly)
Indicates 1:05 as 1 & 05
are the same position
The display will light up Hours & Minutes at the same time
similar to a regular clock.
One blade will light up to show the hour, one blade will flash to
show the minutes. Additional dots may appear to indicate the
exact minute.
II. Flashing Mode
Date icon
Alarm icon
Alarm ON
30 minutes
(flashing)
+3 minutesPM icon
8 o’clock
3. How to check the date & alarm
Press button A to change between [TIME] > [DATE] > [ALARM]
An icon will show to indicate date or alarm.
The date or alarm will be displayed in your chosen display
mode [TURNING] or [FLASHING]
•
•
•
Blade rotates
Date example [Turning Mode]
Alarm example [Flashing Mode]
June 24th
8:33 PM (Alarm ON)
Blade rotates Blade rotates
6 (June) 2 4
*You may choose to show [Month > Day] or [Day > Month]
See section 5 “How to set the date“
From the time display, press & HOLD button B to begin setting
the time.
You will be asked to set the following options in sequence.
4. How to set the time & display modes
•
•
Hours Minutes Mode Animation
The display will flash the current hour.
Press button A to change the hour
Press button B to accept.
•
•
•
I. Hours
*Setting mode will exit after 7 seconds of inactivity
Hour: 11 AM Hour: 7 PM
In the 12-5-9 time telling method, the “group of 10 mins” are
[00, 10, 20, 30, 40, 50]. So in this stage, if the exact minute is
34, you would set 30.
In the 12-5-9 time telling method, the “single mins” are [0-9]. So
in this stage, if the exact minute is 34, you would set 4.
The display will flash the current group of 10 minutes.
Press button A to change the minutes
Press button B to accept.
The display will flash the current single minutes.
Press button A to change the minutes
Press button B to accept.
•
•
•
•
•
•
II. Minutes (group of 10)
III. Minutes (single)
Group of 10 mins
30 mins
00
01
2
3
5
6
7
8
9
4
10
20
30
40
50
Single minutes
4 mins
Blade has 2 display modes [TURNING] & [FLASHING]
See section 1 “How to read the time” for an explaination of
each mode.
Two vertical blades are lit,
a blade rotates.
Two vertical blades are lit,
The top blade flashes.
The display will flash the current display mode.
Press button A to change the mode
Press button B to accept.
•
•
•
IV. Display Mode
Turning Mode Flashing Mode
Change the way you think about time
Table des matières
Autres manuels Kisai Montre
Kisai
Kisai Zone Manuel utilisateur
Kisai
Kisai Quasar Manuel utilisateur
Kisai
Kisai Stencil Manuel utilisateur
Kisai
Kisai RPM Manuel utilisateur
Kisai
Kisai Satellite-X Manuel utilisateur
Kisai
Kisai Radioactive Manuel utilisateur
Kisai
Kisai ONLINE Manuel utilisateur
Kisai
Kisai Seven Manuel utilisateur
Kisai
Kisai Xtal Manuel utilisateur
Kisai
Kisai 3D Unlimited Manuel utilisateur
