Kincrome K12068 Manuel utilisateur

HYDRAULIC TRANSMISSION JACK

Distributed by Kincrome Group www.kincromegroup.com

Owner’s Assembly and Operating Manual

SPECIFICATIONS ..................................................................................................................2

IMPORTANT SAFETY INFORMATION ..................................................................................3

UNPACKING AND ASSEMBLING JACK ................................................................................3

Unpacking Carton ...............................................................................................................3

Handle - Handle Wrench .....................................................................................................3

Testing Handle Operation....................................................................................................3

OPERATING JACK.................................................................................................................4

Preparing Work Area...........................................................................................................4

Using Transmission Jack ....................................................................................................5

Working on Vehicle .............................................................................................................5

MAINTENANCE AND STORAGE...........................................................................................6

Lubricating...........................................................................................................................6

Maintaining Oil Level...........................................................................................................6

Important Note: ...................................................................................................................6

Adding Oil:...........................................................................................................................6

Replacing Oil:......................................................................................................................6

Cleaning..............................................................................................................................6

Storage................................................................................................................................6

Repairing Jack ....................................................................................................................6

SPECIFICATIONS

Working Load limit 500 KG

Height lowered 170 mm

Height raised 680 mm

Handle Length 600 mm

TotalWeight: 45KG

Part Number K12068

IMPORTANT SAFETY INFORMATION

The use of a transmission jack has inherent dangers to avoid risk of personal injury or property damage make

sure you are fully aware of the operating instructions for this product, the recommendations in the vehicle

owners manual prior to using this tool. Do not exceed maximum lifting capacity of 500 kg. This

Transmission jack is intended for automotive use only. Be aware that large or heavy transmissions may

exceed the stated capacity check vehicle owners manual or contact the transmission manufacturer. Do not

use for any other purpose accept the raising and lower of transmission, gear boxes, or differentials. Never

use to raise a vehicle, structure or building, do not lift any human load and never ride on the Transmission

jack.

UNPACKING AND ASSEMBLING JACK

Unpacking Carton

Place carton in a clear, open area such as garage floor. Remove jack and handle from carton.

Handle - Handle Wrench

With the jack sitting on its wheels on a flat surface, place

handle wrench over release valve. Turn handle slowly

clockwise until firm DO NOT over tighten. Remove handle

from release valve and slide handle into handle sleeve.

Testing Handle Operation

Briefly test jack operation as follows BEFORE using to lift any load. With handle on the release valve turning

clockwise or counter clock wise allows jack to be raised and lowered. To raise jack, twist handle completely

clockwise until it stops. Do not force or tighten beyond this point. Take handle from release valve and

place in handle sleeve, Pump handle a few times to raise jack about halfway. If jack does not begin to rise

after a few pumps, check to make sure the release valve is tight. With jack raised, place handle on release

valve twist handle slowly counterclockwise to lower jack. A normal hissing sound may be heard as jack

lowers and pressure in hydraulic cylinder is released.

Table adjustment

Knobs

OPERATING JACK

Preparing Work Area

Before using the transmission jack, it is important to prepare work area properly. Follow this procedure each

time the transmission jack is used to help prevent property damage and or serious injury.

1.) Thoroughly inspect jack for damage or wear before each use. Briefly test operation of unloaded jack

before using to lift any load. If jack is damaged or is malfunctioning DO NOT LIFT ANY LOAD until the

problem is corrected.

2.) Consult vehicle owner’s manual for safety precautions, Transmission weight, and location of support

areas on transmission. The working load limit of the transmission jack is 500 kg. NEVER EXCEED

WORKING LOAD LIMIT OF TRANSMISSION JACK.

3.) Clear children and others from work area before commencing work. Another adult should be nearby for

extra safety and assistance but must be clear of vehicle as it is worked on.

4.) Clear obstructions from work area. Working in tight or cluttered work areas is dangerous.

5.) Be sure transmission jack and vehicle are on solid, level ground such as paved or concrete driveway or

garage floor so the jack is free to roll during lifting and lowering. Uneven or sloped surfaces create

hazardous working conditions and dangerously impeded the function of the jack.

6.) With vehicle in proper position, set vehicle’s parking brake or emergency brake and put gearshift in park

(manual transmissions should be placed in lowest gear). TURN VEHICLE IGNITION OFF AND TO THE

“LOCK” POSITION making sure steering wheel locks.

7.) Chock all wheels of vehicle to prevent vehicle rolling. Using wedge-shaped blocks that tyre cannot roll

over, position one chock tight against the tyre in both forward and reverse rolling paths.

8.) Plan location of transmission jack beneath vehicle, making sure transmission jack will be contacting only

the transmission area of vehicle. Consult vehicle owner’s manual for recommended areas.

Handle

Lifting arm

Release valve

Transmission

Table

Front Wheels

Rear Castors

Using Transmission Jack

zLifting a transmission, gearbox, or differential using a transmission jack can be dangerous. This

transmission jack is designed and intended for use by properly trained and experienced personnel only.

If you are not familiar with the proper and safe operation of a transmission jack, do not use until proper

training and knowledge have been obtained.

Follow all instructions and precautions below.

1.) With lifting arm completely lowered, roll jack into position beneath the transmission of the vehicle.

2.) Twist jack handle completely clockwise to close release valve. Place handle in handle sleeve and slowly

pump handle until transmission table just begins to contact support area on underside of transmission

3.) Adjust the table travel screw and the slant angle screw to align table with the angle of the transmission.

4.) Inspect position of transmission table making sure it is centered and properly engaging the transmission.

5.) Adjust the jaws and chains to secure the transmission to the transmission table.

6.) Pump handle again until transmission table is firm against the transmission – recheck securing chains

and table jaws are firm and secure

7.) Undo transmission from vehicle

8.) Return jack handle to release valve and very slowly turn counter clockwise. Slowly and smoothly lower

transmission excessive speed or jerky motion can cause the transmission to slip leading to property

damage or personal injury.

Working on Vehicle

Any transmission being supported by a jack creates a potentially hazardous working environment.

Never place any part of your body beneath a transmission supported by a jack. Be careful of forces applied

to transmission such as torque on a nut or bolt these forces could cause transmission to become unstable on

transmission table.

MAINTENANCE AND STORAGE

Lubricating

Moving parts on jack should be lubricated occasionally with a light machine oil to maintain efficient

operation. Apply oil to joints on lift arm hinges, push rods, handle base, rear caster wheels, front

wheels, transmission table clamps, and adjusting screws wipe away excess oil with soft cloth.

Maintaining Oil Level

Important Note:

When adding or replacing oil, always use a good grade Hydraulic Jack Oil. Avoid mixing types of oil. DO

NOT use Brake Fluid, Alcohol, Glycerin, Detergent, Motor Oil or Dirty Oil, Improper fluid can cause serious

internal damage to Jack.

Adding Oil:

With transmission table fully lowered & jack on level ground, remove Air Vent Valve. Oil level should be

approx 12 mm below valve hole. If low, add oil as needed then close air vent valve.

Replacing Oil:

For better performance & longevity, replace oil supply once a year. To drain oil, open Air Vent Valve and

loosen the release Valve by turning handle counterclockwise. BE VERY CAREFUL not to permit dirt or

foreign matter to get into the system. Close release valve by turning handle clockwise, fill with good grade

Hydraulic Jack Oil close Air Vent Valve wipe away any spilt fluid. Test jack before lifting a load.

Cleaning

Jack should be wiped clean with soft cloth only. Do not use gasoline, kerosene, or other such solvents or any

abrasive cleanser as cleaning agents and solvents will cause deterioration of the hydraulic seals.

Storage

Before storage, twist release valve 1-1/2 turns counterclockwise to release pressure in hydraulic cylinder.

Store jack level, in a clean environment, preferably indoors, in a dry area to protect jack from moisture.

Repairing Jack

There are no user serviceable parts except as outlined above. Only trained, licensed and certified repair

personnel should attempt any repairs or replacing of parts. Any modifications to this jack, except those

performed by the manufacturer, or their designee, will void all warranties both written an implied.

No. Description Qty No. Description Qty

1 14 mm Snap Spring 2 16 Cotter Pin 1

2 14 mm Washer 4 17 M10 x 20 Screw 6

3 3.5" Wheel 2 18 10 mm Washer 8

4 Base 1 19 8 mm Bolt 2

5 18 mm Snap Spring 2 20 Connector 2

6 φ18 x 22 Pin 1 21 M8 x 50 Hook 2

7 M14 Nut 2 22 Chain 2

8 φ14 Washer 2 23 M10 Bolt 8

9 Positioning Handle 1 24 M8 Bolt 4

10 M14 x 30 Screw 2 25 8 mm Washer 6

11 3.5" Caster 2 26 M8 x 20 Screw 4

12 M12 Bolt 2 27 Angle Iron 2

13 φ12 Washer 2 28 Sheet Iron 4

14 φ12 Washer 2 29 Transmission Platform 1

15 Pump 1 30 Bracket 1

31 Pump Handle 1

Distributed by Kincrome Group www.kincromegroup.com

3 Lakeview Drive Scoresby Victoria

Phone: 1300 657 528

Table des matières

Autres manuels kincrome Jack

kincrome

kincrome K12135 Manuel utilisateur

kincrome

kincrome K12134 Manuel utilisateur

kincrome

kincrome K12162 Manuel utilisateur

kincrome

kincrome K12060 Manuel utilisateur

kincrome

kincrome K12110 Manuel utilisateur

kincrome

kincrome K12066 Manuel utilisateur

kincrome

kincrome K12067 Manuel utilisateur

kincrome

kincrome K12076 Manuel utilisateur

kincrome

kincrome K12130 Manuel utilisateur

kincrome

kincrome K12054 Manuel utilisateur

kincrome

kincrome K12190 Manuel utilisateur

kincrome

kincrome Workshop K12059 Manuel utilisateur

kincrome

kincrome K12057 Manuel utilisateur

kincrome

kincrome K12150 Manuel utilisateur

kincrome

kincrome K12204 Manuel utilisateur

kincrome

kincrome K12058 Manuel utilisateur

kincrome

kincrome K12161 Manuel utilisateur

kincrome

kincrome P12067 Instructions d'utilisation

Manuels Jack populaires d'autres marques

Omega Lift Equipment

Omega Lift Equipment 18122C Instructions d'utilisation

Pittsburgh

Pittsburgh 58816 Instructions de montage

Unimec

Unimec TP Manuel utilisateur

Sonic

Sonic 4800703 Manuel utilisateur

BGS technic

BGS technic 70039 Manuel utilisateur

TradeQuip

TradeQuip 1128T Manuel utilisateur

VEVOR

VEVOR TJD-12000SP-F Manuel utilisateur

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur

Stels

Stels 51131 Manuel utilisateur

Bushranger

Bushranger RJX01 Manuel utilisateur

Clarke

Clarke CTJ2500QLG Manuel d'installation et d'exploitation

Valex

Valex 1650520 Manuel utilisateur

Pfaff

Pfaff Merkur M0 Manuel utilisateur

Beta

Beta 3050/K Supplément

Sealey

Sealey 1050CXHV Manuel utilisateur

Jung

Jung JH Series Manuel utilisateur

URIAH

URIAH UC200020 Manuel utilisateur

Kennedy

Kennedy KSJ010 Manuel utilisateur

kincrome K12068 Manuel utilisateur

Manuels Jack populaires d'autres marques