Kimo CO 110 Mode d’emploi

CO transmitter

CO 110

KEY POINTS

ABS V0



- duct model: IP65

- ambient model: IP20

LCD 10 digit . Size: 50 x 17 mm

Value: 10 mm; Unit: 5 mm

for cable Ø 8 mm

maximum

138 g (ambient model); 150 g (duct model)

- Range from 0 to 500 ppm

- 0-10 V active output, power upply 24 Vac/Vdc (3-4 wire ) or 4-20 mA output, pa ive loop,

power upply from 16 to 30 Vdc (2 wire )

- ABS V0 hou ing, IP65 (depending on model), with or without di play

- “¼ turn” y tem mounting with wall-mount plate

- Hou ing with implified mounting y tem

FEATURES OF HOUSING

TECHNICAL FEATURES

 ppm

 From 0 to 500 ppm

 ±3 ppm or 3% of the mea ured value

! Electrochemical en or

"# 5 year

$ T63 = 35

$ 0.1 ppm

! Air and neutral ga

%&'$& From 0 to +50 °C. In non-conden ing condition. From 0 to 2000 m.

( From -10 to +70 °C

PART NUMBER

)**+

To order, ju t add the code to complete the part number :

,&)

- Active – 24 Vac/Vdc – 0-10 V

-Pa ive – 16/30 Vdc – 4-20 mA



) with di play

.without di play

/0)**+#)

CO tran mitter, 4-20 mA pa ive tran mitter, with di play

and duct probe

*All the accuracie indicated in thi technical data heet were tated in laboratory condition , and can be guaranteed for mea urement carried out in the ame condition , or carried out with calibration compen ation.

!

- Duct

(-ambient





90 mm

41 mm

80 mm

150 mm

46 mm 90 mm

109 mm

TECHNICAL SPECIFICATIONS

CONNECTIONS

Inactive

witch

)&, - active 0-10 V (power upply 24 Vac/Vdc ± 10%), 3-4 wire

- pa ive loop 4-20 mA (power upply 16/30 Vdc), 2 wire

- Common mode voltage <30 VAC

- maximum load : 500 Ohm (4-20 mA) / minimum load : 1 K Ohm (0-10 V)

 2 VA (0-10 V) or 0.6 VA (4-20 mA)

/1 2004/108/EC EMC ; 2006/95/EC Low Voltage ; 2011/65/EU RoHS II ; 2012/19/EU WEEE

/ Screw terminal block for cable from 0.05 to 2.5 mm2 or from 30 to 14 AWG

Carried out according to the code of good practice.

 USB-mini DIN cable

/1 Air and neutral ga

2

ELECTRICAL CONNECTIONS – as per NFC15-100 standard

Active

witch

!34!5674

76 L

Power upply

24 Vac

class II

VCO

GND

Power upply

24 Vdc



8

,

!59#,6,6

4(,,4

123

Power upply

24 Vdc

9,

8, 9,

123

-Power upply

24 Vac

class II

9,

For )**+# model with +#*+: – 1-

Regulator di play or

PLC/BMS

1

Regulator di play or PLC/BMS 1

VCO

GND

Electrochemical

en or

Power upply

terminal block

Output terminal block

LCC-S

oftware

connection

;05

$1

Cable gland



GND VCO

For )**+# model with 8#<+– 1:

<,

Ico

Power upply

16-30 Vdc

Vdc

Ico

Vdc

<,

SETTINGS AND USE OF THE TRANSMITTER

➢

!674!5352,,

,,46,4

To configure the tran mitter, un crew the 4

crew of the hou ing then open it. DIP

witche allowing the different etting are

acce ible.

...

Di play/regulator/PLC

1

To et a mea uring range, put the on-off witche 2, 3 and 4 a hown below :

➢

Di play/regulator/PLC

1

On-off witch

Setting of

mea uring range

MOUNTING

To mount the tran mitter, mount the ABS plate on the wall (drilling : Ø6 mm, crew and pin are

upplied).

In ert the tran mitter on the fixing plate ( ee A on the drawing be ide). Rotate the hou ing in

clockwi e direction until you hear a “click” which confirm that the tran mitter i correctly in talled.

7.5

4.5

37.5

23.75

04

8054

34

16-30 Vdc

,,=

It i po ible to configure intermediary range .

Attention : the minimum difference between the minimum scale and the maximum scale is 20.

Example: for a 0-500 ppm tran mitter, the minimum delta i 20 ppm. So the tran mitter could be configure from 0

to 70 ppm from 0 to 20 ppm.

• To acce to the configuration via oftware :

- Set the witch a hown be ide.

- Connect the cable of the LCC-S to the connection of the tran mitter.

• To configure the tran mitter, plea e refer to the LCC-S u er manual.

Caution : The configuration of the parameters can be done either by DI switch, or by software (you cannot combine both solutions).

CONFIGURATION IA LCC-S SOFTWARE (optional)

(,*



 1

+>++ ;+*++ ;+<++



Off On

1

Active witch

FTang_CO110 – 03/03/15 – RCS (24) Périgueux 349 282 095 Non-contractual document – We re erve the right to modify the characteri tic of our product without prior notice.

MAINTENANCE

Plea e avoid any aggre ive olvent. Plea e protect the tran mitter and it probe from any cleaning product containing formol, that may be u ed for cleaning

room or duct .

OPTIONS AND ACCESSORIES

●?2"#*++Power upplycla 2, 230 Vac input, 24 Vac output

●?2"#*++ Power upplycla 2, 230 Vac input, 24 Vdc output

●"#( configuration oftware with USB cable

POSITIONING OF THE PROBE

For duct model , the po itioning of the probe i important to get accurate mea urement : the hole located next to the crew at the end of the probe mu t face

the air flow.

Procedure to modify the po itioning of the end of the probe:

➢Un crew the crew.

➢Turn the end of the probe: the hole mu t face the air flow.

➢Replace the crew.

Screw

End of the probe

Hole

),14

PRECAUTIONS FOR USE

Plea e alway u e the device in accordance with it intended u e and within parameter de cribed in the technical feature in order not to compromi e the

protection en ured by the device.

Once returned to KIMO, required wa te collection will be a ured in the re pect of the environment in accordance with European guideline relating to WEEE.

Table des matières

Autres manuels Kimo Instrument de mesure