Kidde 29J Manuel utilisateur

For your convenience, write down the following

information. If you call our Consumer Hotline,

these are the first questions you will be asked.

Smoke Alarm Model Number

(located on back of alarm):

Date Code (located on back of alarm):

The National Fire Protection Association

(NFPA) and the manufacturer

recommend replacing this alarm

ten years from the date code.

Date of Purchase:

Where Purchased:

820-0914 REV. B

11/2006

0307-7201-00

For models:

29J, 29HJ, 29HIJ

9 Volt Battery Operated Photoelectric Smoke Alarm

Thank you for purchasing this smoke alarm. It is an important

part of your family’s home safety plan. You can trust Kidde to

provide the highest quality safety protection. We know you

expect nothing less when the lives of your family are at stake.

Photoelectric Smoke Alarm

User’s Guide

29J

REMOVAL OF BATTERY WILL RENDER THE SMOKE ALARM

INOPERATIVE.

IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLA-

TION AND KEEP THIS MANUAL NEAR THE ALARM FOR

FUTURE REFERENCE.

CONTENTS OF THIS MANUAL

1 -- RECOMMENDED LOCATIONS FOR SMOKE ALARMS

2 -- LOCATIONS TO AVOID

3 -- INSTALLATION INSTRUCTIONS

4 -- OPERATION AND TESTING

5 -- NUISANCE ALARMS

6 -- MAINTENANCE

7 -- FIRE SAFETY

8 -- GOOD SAFETY HABITS

9 -- NFPA REQUIRED PROTECTION

10 -- CAUTION

11-- SERVICE AND WARRANTY

1. RECOMMENDED LOCATIONS FOR ALARMS

• Locate the first alarm in the immediate area of the bedrooms.

Try to monitor the exit path as the bedrooms are usually farthest

from the exit. If more than one sleeping area exists, locate addi-

tional alarms in each sleeping area.

• Locate additional alarms to monitor any stairway as stairways act

like chimneys for smoke and heat.

• Locate at least one alarm on every floor level.

• Locate an alarm in every bedroom.

• Locate an alarm in every room where electrical appliances are

operated (i.e. portable heaters or humidifiers).

• Locate an alarm in every room where someone sleeps with the

door closed. The closed door may prevent an alarm not located

in that room from waking the sleeper.

• Smoke, heat, and combustion products rise to the ceiling and

spread horizontally. Mounting the smoke alarm on the ceiling in

the center of the room places it closest to all points in the room.

Ceiling mounting is preferred in ordinary residential construction.

• When mounting an alarm on the ceiling, locate it at a minimum

of 4” (10cm) from the side wall (see figure 1).

• When mounting the alarm on the wall, use an inside wall with

the top edge of the alarm at a minimum of 4” (10cm) and a

maximum of 12” (30.5cm) below the ceiling (see figure 1).

• Put smoke alarms at both ends of a bedroom hallway or large

room if the hallway or room is more than 30 ft (9.1 m) long.

• Install Smoke Alarms on sloped, peaked or cathedral ceilings at

or within 3ft (0.9m) of the highest point (measured horizontally).

NFPA 72 states: “Smoke alarms in rooms with ceiling slopes

greater than 1 ft in 8 ft (.3m in 2.4m) horizontally shall be locat-

ed on the high side of the room.” NFPA 72 states: “A row of

alarms shall be spaced and located within 3 ft (0.9m) of the

peak of the ceiling measured horizontally” (see figure 3).

2. LOCATIONS TO AVOID

In general alarms should not be located:

•In the garage. Products of combustion are present when you

start your automobile.

• Less than 4” (10cm) from the peak of an “A” frame type ceiling.

• In an area where the temperature may fall below 40ºF or rise

above 100ºF, such as garages and unfinished attics.

•In dusty areas. Dust particles may cause nuisance alarm or fail-

ure to alarm.

FIGURE 1

FIGURE 2FIGURE 3

• In very humid areas. Moisture or steam can cause nuisance

alarms.

• In insect-infested areas.

• Smoke alarms should not be installed within 3 ft (.9m) of the

following: the door to a kitchen, the door to a bathroom con-

taining a tub or shower, forced air supply ducts used for heating

or cooling, ceiling or whole house ventilating fans, or other high

air flow areas.

• Kitchens. Normal cooking may cause nuisance alarms. If a

kitchen alarm is desired, it should have an alarm silence feature.

• Near fluorescent lights. Electronic “noise” may cause nuisance

alarms.

• Smoke alarms are not to be used with detector guards unless

the combination (alarm and guard) has been evaluated and

found suitable for that purpose.

• Battery powered smoke alarms are not designed to be installed

over an electrical box or opening and must not be installed in

this manner.

3. INSTALLATION INSTRUCTIONS

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOV-

ABLE!

NOTE: THE 29HIJ MOUNTING PLATE MOUNTS IN AN IDENTICAL

MANNER EVEN THOUGHT IT IS DIFFERENT IN APPEARANCE.

When mount-

ing in a hallway,

the “A” line

should be

parallel with

the hallway.

For wall mount-

ing the “A”

line should be

horizontal and

the arrow must

be pointing up.

Alignment Marks

FIGURE 5

FIGURE 4

FIGURE 6 FIGURE 7

Push Down Alignment

Marks

Install Remove

CAUTION! BE SURE THE ALIGNMENT MARKS ON THE 29HIJ

ALARM AND MOUNTING PLATE ARE LINED UP (SEE FIGURE 7)

WHEN INSTALLING THE ALARM ON THE MOUNTING PLATE.

THIS ALARM WILL ONLY ATTACH IN ONE ORIENTATION.

1.Remove the mounting plate from the back of the alarm by hold-

ing the mounting plate and twisting the alarm in the direction

indicated by the “OFF” arrow on the alarm cover.

2.To insure aesthetic alignment of the alarm with the hallway or

wall, the “A” line on the mounting plate should be parallel with

the hallway when ceiling mounting or horizontal when wall

mounting.

3.After selecting the proper smoke alarm location as described in

section 1, attach the mounting plate to the ceiling as shown in

figure 4. For wall mounting see figure 5. Place mounting plate

on the wall. Be sure the “UP FOR WALL MOUNTING “ text and

arrow are facing up. Use the screws and anchors provided to

secure the mounting plate (use 3/16” drill bit for anchor holes).

4.When installing the battery, press the battery reminder finger

down into the battery compartment and install the battery (see

figure 6).

CAUTION! IF THE BATTERY REMINDER FINGER IS NOT HELD

DOWN IN THE BATTERY COMPARTMENT BY THE BATTERY,

THE ALARM WILL NOT ATTACH TO THE MOUNTING BRACKET.

5. Alignment marks are provided on the edge of the trim plate

and the alarm. After installing the mounting plate, place the

alarm on the mounting plate with the alignment marks lined up.

Twist the alarm in the direction indicated by the “ON” arrow on

the alarm cover (see figure 7) until it locks in place.

6. TAMPER RESIST FEATURE:

ACTIVATING THE TAMPER RESIST FEATURE

To make your smoke alarm tamper

resistant, a tamper resist means has

been provided. To activate this feature

you must break out the tamper resist

blocks. Use a small screwdriver to

break out these blocks on the alarm

(See figure 8).

Note: 29HIJ has only one tamper resist

block. FIGURE 8

Break

out

Using this feature will help deter children and others from

removing the alarm from the mounting plate. With the blocks

removed the tamper resist feature will be activated when the

alarm is installed on the mounting plate.

7.REMOVING ALARM WITH TAMPER RESIST FEATURE ACTIVE

The tamper resist tab will have to be

released in order to change the bat-

tery. Using a tool (small screwdriver)

pull the tamper resist tab away from

the mounting plate (See figure 9).

With the tamper resist tab held away

from the alarm and rotate the alarm

in the off direction.

8.After installation, test your alarm by

depressing and holding down the test

button for several seconds, this should sound the alarm.

INTERCONNECTING ALARMS. (MODEL 29HIJ ONLY)

This model is equipped with interconnect capability. When alarms

are interconnected in a multiple station arrangement they must

not exceed the NFPA interconnect limit of 12 smoke alarms.

CAUTION! Do not interconnect with AC smoke alarms and

do not connect to AC power. Doing so will damage the

alarm and present a shock hazard.

The total length of wire that can be used in the interconnect sys-

tem is 650 ft (200 Meters). The interconnect wires should not be

routed near fluorescent or discharge type lighting fixtures. Total

Wire Diameter (including insulation) should be between 1.5 mm

and 2.4mm, with a Conductor Diameter not less than 0.9mm.

Wire access slots are provided on both sides of the alarm mount-

ing plate. Use pliers to breakout the desired access slot (see figure

10). Once the breakout has been removed, the wires can be rout-

ed to the screw connection (See figure 11). Be sure to observe the

wire polarity and connect all interconnected alarms utilizing the

correct polarity. It is possible to have more than one wire connect-

ed to each screw (see figure 12).

FIGURE 9

4. OPERATION AND TESTING

OPERATION: The smoke alarm is operating once a fresh battery is

installed and testing is complete. When products of combustion

are sensed, the unit sounds a loud 85db pulsating alarm until the

air is cleared.

INTELLIGENT HUSHTM CONTROL

Note: The model 29J does not have Hush®

The “HUSH®” feature has the capability of temporarily desensitiz-

ing the alarm circuit for up to 8 minutes. This feature is to be used

only when a known alarm condition, such as smoke from cooking,

activates the alarm. The smoke alarm is desensitized by pushing

the “HUSH®” button on the smoke alarm cover. If the smoke is

not too dense, the alarm will silence immediately and the red LED

will flash every 1.5 seconds while in Hush®. This indicates that the

alarm is in a temporarily desensitized condition. The smoke alarm

will automatically reset after 8 minutes and sound the alarm if par-

ticles of combustion are still present.

The “HUSH®” feature can be used repeatedly until the air has

been cleared of the condition causing the alarm. Pushing the

test/reset button on the alarm will end the Hush®period.

(- )

(+)

FIGURE 10

FIGURE 12

ALARM 1 ALARM 12

FIGURE 11

NOTE: DENSE SMOKE WILL OVERRIDE THE “HUSH®” CON-

TROL FEATURE AND SOUND A CONTINUOUS ALARM.

CAUTION: BEFORE USING THE ALARM “HUSH®” FEATURE,

IDENTIFY THE SOURCE OF THE SMOKE AND BE CERTAIN A

SAFE CONDITION EXISTS.

FLASHING LED LIGHT: This smoke alarm is equipped with a flash-

ing Red indicator light with three modes of operation:

Normal Operation

The LED flashing every 40 - 45 seconds indicates that the smoke

alarm battery is properly installed and the alarm is operating.

Alarm Mode / Originating Unit Indicator

The LED will Flash about every second when the alarm is sounding

(constant pulsating sound) as a result of the test button being acti-

vated or the smoke sensing chamber senses particles of combustion.

WHEN UNITS ARE INTERCONNECTED, Model 29HIJ only, the red

LED of the alarm that senses the smoke or is being tested (the

originating unit) will flash rapidly. All other units in the intercon-

nect system will sound an alarm but their red LED's will NOT flash

rapidly.

Hush® Mode.

The LED will Flash approximately every 1.5 seconds indicating the

alarm is in the "Hush®" mode.

SMOKE SENSING CHAMBER OPERATION: This alarm will "chirp" if

any of the components in the smoke-sensing chamber fail. This

chirp will occur between the normal standby flashes of the red

LED indicator light. (If the chirp occurs at the same time as the red

LED flash, this indicates a low battery, see section 6 for low battery

information.

ALARM MEMORY

This unit features an alarm memory to inform you that the alarm

has sounded since the test button was last pressed. If the alarm

memory is set the red LED will flash rapidly when the test button is

pressed. The alarm memory is reset when the test button is

released.

TESTING:

NOTE: WEEKLY TESTING IS REQUIRED!

CAUTION: Due to the loudness (85 decibels) of the alarm, always

stand an arms length away from the unit when testing.

Test by pushing the test button on the cover and holding it down

for a minimum of 5 seconds (or until the unit sounds). This will

sound the alarm if the electronic circuitry, horn, and battery are

working. If no alarm sounds, the unit has defective batteries or

other failure. DO NOT USE AN OPEN FLAME to test your alarm,

you could damage the alarm or ignite combustible materials and

start a fire.

TEST THE ALARM WEEKLY TO ENSURE PROPER OPERATION. Erratic

or low sound coming from your alarm may indicate a defective

alarm, and it should be returned for service (see section 11).

NOTE: WEEKLY TESTING IS REQUIRED.

5. NUISANCE ALARMS

Smoke alarms are designed to minimize nuisance alarms.

Cigarette smoke will not normally set off the alarm, unless the

smoke is blown directly into the alarm. Combustion particles from

cooking may set off the alarm if the alarm is located close to the

cooking area. Large quantities of combustible particles are gener-

ated from spills or when broiling. Using the fan on a range hood

which vents to the outside (non-recirculating type) will also help

remove these combustible products from the kitchen.

If the alarm does sound, check for fires first. If a fire is discovered,

get out and call the fire department. If no fire is present, check to

see if one of the reasons listed in section 2 may have caused the

alarm.

6. MAINTENANCE

BATTERY REPLACEMENT

If tamper resist feature has been used, refer to “REMOVING

ALARM WITH TAMPER RESIST FEATURE ACTIVE” in section 3 for

removal instructions.

To replace the battery, remove the alarm from the mounting plate

by rotating the alarm in the direction of the “OFF” arrow on the

cover (see section 3, figure 7).

This Smoke Alarm is powered by 9 volt battery (carbon Zinc, alka-

line, and Lithium batteries may be used). A fresh battery should

last for one year under normal operating conditions. Alkaline and

Lithium batteries will last longer than carbon Zinc batteries. This

alarm has a low battery monitor circuit which will cause the alarm

to “chirp” approximately every 30 - 40 seconds for a minimum of

seven (7) days when the battery gets low. Replace the battery

when this condition occurs. These batteries are available at many

local retail stores.

USE ONLY THE FOLLOWING 9 VOLT BATTERIES FOR SMOKE

ALARM REPLACEMENT.

Carbon Zinc Type: EVEREADY 1222; GOLD PEAK 1604S

Alkaline Type: ENERGIZER 522; DURACELL MN1604,

MX1604, GOLD PEAK 1604A; PANASONIC

6AM6, 6AM-6, 6AM-6PI, 6AM6X,

and 6LR61(GA)

Lithium Type: ULTRALIFE U9VL-J

NOTE: WEEKLY TESTING IS REQUIRED.

WARNING!! USE ONLY THE BATTERIES SPECIFIED. USE OF

DIFFERENT BATTERIES MAY HAVE A DETRIMENTAL EFFECT

ON THE SMOKE ALARM.

CLEANING YOUR ALARM

YOUR ALARM SHOULD BE CLEANED AT LEAST ONCE A YEAR

To clean your alarm, remove it from the mounting bracket as out-

lined in the beginning of this section (If tamper resist feature has

been used, refer to “REMOVING ALARM WITH TAMPER RESIST

FEATURE ACTIVE” in section 3 for removal instructions).

You can clean the interior of your alarm (sensing chamber) by

using compressed air or a vacuum cleaner hose and blowing or

vacuuming through the openings around the perimeter of the

alarm. The outside of the alarm can be wiped with a damp cloth.

After cleaning, reinstall your alarm and test your alarm by using

the test button. If cleaning does not restore the alarm to normal

operation the alarm should be replaced.

Do not paint your alarm. Paint will seal the vents and interfere

with the alarms ability to detect smoke and produce sound. Never

attempt to dismantle the alarm or clean the inside, as this will void

the warranty.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kidde Détecteur de fumée

Kidde

Kidde PI2010CA Manuel utilisateur

Kidde

Kidde 29D Manuel utilisateur

Kidde

Kidde 10SCO Manuel utilisateur

Kidde

Kidde WFP Manuel utilisateur

Kidde

Kidde I240C Manuel utilisateur

Kidde

Kidde i12010SCO Manuel utilisateur

Kidde

Kidde 1276CA Manuel utilisateur

Kidde

Kidde P4010ACSAQ-WF Manuel utilisateur

Kidde

Kidde PI9000 Manuel utilisateur

Kidde

Kidde 1285 Manuel utilisateur

Kidde

Kidde 19HI Manuel utilisateur

Kidde

Kidde 0916LL Manuel utilisateur

Kidde

Kidde HD135F Manuel utilisateur

Kidde

Kidde PI9000 Manuel utilisateur

Kidde

Kidde i4618AC Manuel utilisateur

Kidde

Kidde P3010H Manuel utilisateur

Kidde

Kidde i12010S Manuel utilisateur

Kidde

Kidde PI2000CA Manuel utilisateur

Kidde

Kidde 1276 Manuel utilisateur

Kidde

Kidde P4010ACSCO-W Manuel utilisateur

Kidde

Kidde 0910UK Manuel utilisateur

Kidde

Kidde i9060CA Manuel utilisateur

Kidde

Kidde i12040A Manuel utilisateur

Kidde

Kidde AirSense Stratos Micra 25 Manuel utilisateur

Manuels Détecteur de fumée populaires d'autres marques

x-sense

x-sense SD19-W Manuel utilisateur

BRK electronic

BRK electronic First Alert P1010 Manuel utilisateur

FireAngel

FireAngel Thermoptek ST-622 Manuel utilisateur

teko

teko Astra-42A Manuel utilisateur

Safetec

Safetec SDS-2/6 Manuel du propriétaire

Siemens

Siemens PE-11C Manuel utilisateur

System Sensor

System Sensor DH500ACDC Manuel utilisateur

Resolution Products

Resolution Products RE612 CryptiX Manuel utilisateur

First Alert

First Alert PC900V Manuel utilisateur

Eminent

Eminent EM6590 E-Domotica Manuel utilisateur

Ei Electronics

Ei Electronics Ei Ei168RC Manuel utilisateur

Carrier

Carrier Kidde Quell Q301 Manuel utilisateur

VESDA

VESDA VLF-500 Manuel utilisateur

ELRO

ELRO FS8110 Manuel utilisateur

Heiman

Heiman SMOKI NS-626PHS Manuel utilisateur

Regin

Regin SDD-S65 Manuel utilisateur

Family Gard

Family Gard FG225 Manuel utilisateur

Greystone

Greystone DSD120 Manuel utilisateur