Kicker 19417166 Manuel utilisateur

19417166-20190620

19417166

Designed for 2019 and newer

Chevrolet® Silverado 1500

and GMC® Sierra 1500 Crew

Cab or Double Cab trucks with

HD radio.

Subwoofer Harness

Subwoofer Assembly

Amplifier Assembly

Subwoofer Power Harness

Amplifier Power Harness

M6 Nuts x 3

Wire Ties x 6

Fuse x 2

Adaptor Harness

Self-Drilling Screws x 2

Amplifier Harness

Fig. 5

1. Disconnect negative battery cable.

2. Remove the cover of the battery junction box. Fig. 1

3. Make sure supplied fuse is not installed in fuse holder and connect the subwoofer and amplifier

power wires to the studs pictured in figure 2. Either wire can go to either stud Torque to 4.7Nm

(42in-lb)

4. Route the power wires toward the firewall and secure with supplied wire ties.

5. Find the rubber grommet behind the battery and cut the end of the accessory tube. Feed the

power wires through the grommet tube into the cabin. Fig. 3

6. Install the white three pin power connectors on each power wire. Close the retainer.

Fig. 4

NOTE: Do not mix terminals from power wires between connectors. Make sure

all three wires from each power wire are each in a single connector.

7. Connect one power wire to the subwoofer

harness and one to the amplifier harness. Fig. 5

Fig. 1

Connect one power

harness to each

terminal

Fig. 2

Then

retainer

Insert terminals first.

Any wire can be in

any position.

Fig. 4

Fig. 3

8. If equipped with power seats, adjust the passenger seat as high as possible. Remove the panel

next to the seat. Fig. 6

9. Remove the front kick/sill trim panel as well as the rear sill panel. Fig. 7

10.Find the Audio Control Module (ACM) located above the right kickpanel area. Fig. 8 & 9

11.Disconnect the 28-pin gray connecter and connect it to the amplifier harness. To disconnect,

slide the white locking retainer out of the connector until it stops in order to press the connector

release tab. (Generic connector shown already disconnected from ACM for clarity). Fig. 10 & 11

Fig. 11

Fig. 6

Fig. 7

ACM Location

Fig. 9

ACM

Front of vehicle

Fig. 8

Fig. 10

Fig. 15

12.Connect the gray amplifier harness connector to

the ACM.

13.Disconnect the 28-pin black connector from the

ACM. Carefully cut away approximately 3 inches

of the black cloth wrapping the harness. Find

the green with black strip wire and cut. Strip

back about ¼inch of wire on each cut end.

Fig.12

See Splicing Technique section

14.Using the supplied butt connectors, connect the harness wire labeled, “connector”to the cut

wire attached to the ACM connector. Connect the harness wire labeled, “harness”to the other

cut wire. Fig. 13 & 14.

15.Connect the ground wires of both harness to the

ground point located in the right front kick panel

area. Fig. 15 Tighten to 7.5Nm (66in-lb)

16.Remove the four screws securing the front and

rear wire protector and route the subwoofer

harness alongside the factory harness securing

with supplied wire ties. Replace wire protectors.

Fig. 16

17.Remove the two 10mm nuts securing the jack

bracket. Fig. 17

18.Remove the jack tool bag.

Fig. 16

Fig. 17

Fig. 12

Fig. 13

Fig. 14

Fig. 18

NOTE: If equipped with the optional carpeted storage tray as pictured in Fig.

17, remove at this time. The storage tray cannot be used in conjunction with

the subwoofer. The subwoofer by design provides an optional storage area

once it is installed.

19.Remove the outer rear seat bolt on the driver’s

side. Fig. 18

20.Make cuts in the carpet according to the

measurement in Fig. 19. Only make cuts where

dotted lines shown.

21.Remove the rear seatback. See Second Row

Seat Removal Section.

22.Route subwoofer harness and the amplifier

from passenger’s side to driver’s side under

carpet. Subwoofer harness should be routed

behind seat brackets. Routing from one precut

opening to the next will aid in harness routing.

Fig. 20

1 inch

Fig. 19

Fig. 22

23.Route the black four pin subwoofer connector out of the hole that was cut near the stud where

the jack tools attach. Route the white amplifier connector behind seat bolts and out of the hole

that was cut near outer seat bolt. Fig. 21

24.Make wire harness connections to subwoofer and amplifier and set subwoofer in place aligning

brackets with the stud and seat bolt hole. Fig. 22

25.Reinstall the jack tool bag and nut.

NOTE: MAKE SURE WIRE HARNESS IS NOT BEING CRUSHED UNDER JACK

TOOL BAG!

26.Reinstall seat bolt. Torque to 109Nm (80ft/lb)

27.Mount the amplifier/bracket assembly over the studs on the back wall and secure with supplied

nuts. Torque to 4Nm (35in/lb) Fig. 23

NOTE: In rare instances, the upper mounting studs may be missing. If the

upper mounting studs are missing use the supplied self-drilling screws to

secure the top of the amplifier bracket. Fig. 24

28.Secure amplifier harness to back wall and connect to the amplifier.

29.Connect the two-pin connector of the amplifier to the two-pin connector of the subwoofer

harness. Fig. 23 (arrow)

Fig. 20

Fig. 21

Fig. 23

Fig. 24

30.Reinstall all previously removed parts in reverse order.

NOTE: MAKE SURE WIRE HARNESS IS NOT BEING CRUSHED WHEN

REINSTALLING JACK BRACKET!

31.Install supplied fuses into fuse holders.

32.Reconnect negative battery cable. Tighten to 7.5Nm (66in-lb)

SplicingTechnique

Use a sewing seam ripper, available from sewing supply stores, in order to cut open the harness in

order to avoid wire insulation damage.

Cut as little wire off the harness as possible. You may need the extra length of wire in order to change

the

location of a splice.

Strip approximately 5.0 mm (0.20 in) of insulation from each wire to be spliced.

Do not nick or cut any of the strands. Inspect the stripped wire for nicks or cut strands.

If the wire is damaged, repeat this procedure after removing the damaged section.

Select the red DuraSeal splice sleeve Part #

19168446 for 18-22 AWG wire

5. Place the DuraSeal splice sleeve in the crimp tool.

If using the EL-38125-10 splice sleeve crimping tool, use crimp nest number 2.

If using the

J-38125-8 splice sleeve crimping tool, use crimp nest number 1

6. Close the hand crimper handles slightly in order to firmly hold the DuraSeal splice sleeve in the

proper

nest.

Insert the wire into the splice sleeve barrel until the wire hits the barrel stop.

Tightly close the handles of the crimp tool until the crimper handles open when released.

The crimper handles will not open until you apply the proper amount of pressure to the DuraSeal

splice sleeve. Repeat steps7 and 8 for the opposite end of the splice.

Using the heat torch, apply heat to the crimped area of the barrel.

Start in the middle and gradually move the heat barrel to the open ends of the tubing:

The tubing will shrink completely as the heat is moved along the insulation.

A small amount of sealant will come out of the end of the tubing when sufficient shrinkage is

achieved.

Release Button

Seatback Removal

Removing O/B Head Restraints and CTR Head Rest.

Remove O/B head restraints by pushing in on two release buttons on head rest guide caps and lifting up on head

restraint (qty 2) Fig. 1 & 2

Remove CTR head rest by pushing in on two release buttons on head rest guide caps and lifting up on head rest (qty

1) Fig. 1 & 2

Removing Seat Back from Vehicle

Remove 6 Head rest guides from seat back/BIW by

inserting 90 degree awl into guide with front of awl

point facing forward, locate groove in guide plastic

(located on passenger or driver side of centerline of

guide and rotate awl 90 degrees then lift up on the awl

to pull guide free of seatback and BIW. Fig. 3 and Fig. 4

Fig. 1

Fig. 2

Fig. 3

Fold 60/40 cushions to upright position Fig. 5

Insert awl into groove in head rest guide, then

rotate 90 degrees and pull up on tool to pull

guide from BIW

Fig. 4

Fig. 5

Locate and remove 4 M6 lower attachment bolts securing the seat back to the BIW cab wall. Fig. 6

Using angled awl with point facing passenger side of vehicle – find latch release lever located to passenger side of

each child seat re-router loop below the seat back trim. Insert awl into release lever on latch and pull vertically up

10-20 mm while pulling seat back forward to disengage striker from latch (Qty 3 latches – Passenger, Driver and

Center) Release order does not matter Fig. 7, Fig. 8, Fig. 9. Fig. 10

Seat back can now be removed from the vehicle.

Remove M6 Lower attachment bolts – (Qty 4)

Fig. 6

Fig. 7

Table des matières

Autres manuels Kicker Subwoofer

Kicker

Kicker S18XSP Manuel utilisateur

Kicker

Kicker DES12 Manuel utilisateur

Kicker

Kicker COMP8 Manuel utilisateur

Kicker

Kicker L7R Series Manuel utilisateur

Kicker

Kicker CompVR CVR12 Manuel utilisateur

Kicker

Kicker Solo-Baric S15L5 Manuel utilisateur

Kicker

Kicker COMPVT CVT124 Manuel utilisateur

Kicker

Kicker PSON13 Manuel utilisateur

Kicker

Kicker Solo-Baric S1L7 Manuel utilisateur

Kicker

Kicker SOLO-BARIC L7S12 Manuel utilisateur

Kicker

Kicker CompVT CVT12 Manuel utilisateur

Kicker

Kicker SOLO-BARIC S10L3 Manuel utilisateur

Kicker

Kicker Hideaway HS8 Manuel utilisateur

Kicker

Kicker Impulse 10i Manuel utilisateur

Kicker

Kicker Solo-Baric C-Series Manuel utilisateur

Kicker

Kicker CVX COMPVX10 Manuel utilisateur

Kicker

Kicker SOLO-BARIC S15L7 Manuel utilisateur

Kicker

Kicker CompVR CVR10 Manuel utilisateur

Kicker

Kicker Comp DC12 Manuel utilisateur

Kicker

Kicker Solo-Baric D-Series Manuel utilisateur

Kicker

Kicker CVX COMPVX12 Manuel utilisateur

Kicker

Kicker CompS10 Manuel utilisateur

Kicker

Kicker GOLD Series Manuel utilisateur

Kicker

Kicker PWRA4P11 Manuel utilisateur

Manuels Subwoofer populaires d'autres marques

Sony

Sony XS-AW8 Manuel utilisateur

Sony

Sony XS-L836 Manuel utilisateur

B&C Speakers

B&C Speakers 15 HPL 76W Manuel utilisateur

Velodyne

Velodyne DD-18+ Manuel utilisateur

Sonance

Sonance Cinema Series SUB 10-150 Manuel utilisateur

Hifonics

Hifonics HW-12 Guide de démarrage rapide

Magnat Audio

Magnat Audio ADR 130 BP Manuel utilisateur

Blitz

Blitz BZP106 Manuel utilisateur

Technics

Technics SB-AS500 Manuel utilisateur

Lyngdorf

Lyngdorf BW-2 Manuel utilisateur

Lyngdorf

Lyngdorf BW-3 Manuel utilisateur

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Manuel utilisateur

REL Acoustics

REL Acoustics Q Series Manuel utilisateur

Pioneer

Pioneer Elite S-W1EX Manuel utilisateur

L-Acoustics

L-Acoustics KIVA SB15M Guide de démarrage rapide

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Manuel utilisateur

KEF

KEF KUBE 200 Manuel utilisateur

Yamaha

Yamaha SW500 Manuel utilisateur