Keysight 16442B Manuel utilisateur
Keysight 16442B Test Fixture
User’s Guide
Notices
© Keysight Technologies 2002-2014
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation into
a foreign language) without prior agreement
and written consent from Keysight Technolo-
gies as governed by United States and inter-
national copyright laws.
Manual Part Number
16442-90100
Edition
Edition 1, December 2002
Edition 2, July 2006
Edition 3, August 2014
Printed in Malaysia
Published by:
Keysight Technologies Japan K.K.
9-1, Takakura-cho, Hachioji-shi, Tokyo
192-8550 Japan
Warranty
The material contained in this docu-
ment is provided “as is,” and is subject
to being changed, without notice, in
future editions. Further, to the maxi-
mum extent permitted by applicable
law, Keysight disclaims all warranties,
either express or implied, with regard
to this manual and any information con-
tained herein, including but not limited
to the implied warranties of merchant-
ability and fitness for a particular pur-
pose. Keysight shall not be liable for
errors or for incidental or consequential
damages in connection with the fur-
nishing, use, or performance of this
document or of any information con-
tained herein. Should Keysight and the
user have a separate written agreement
with warranty terms covering the mate-
rial in this document that conflict with
these terms, the warranty terms in the
separate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
If software is for use in the performance of a
U.S. Government prime contract or subcon-
tract, Software is delivered and licensed as
“Commercial computer software” as defined
in DFAR 252.227-7014 (June 1995), or as a
“commercial item” as defined in FAR 2.101(a)
or as “Restricted computer software” as
defined in FAR 52.227-19 (June 1987) or any
equivalent agency regulation or contract
clause. Use, duplication or disclosure of
Software is subject to Keysight Technologies’
standard commercial license terms, and
non-DOD Departments and Agencies of the
U.S. Government will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Govern-
ment users will receive no greater than Lim-
ited Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any tech-
nical data.
Declaration of Conformity
To get the latest version of the declaration of
conformity, go to http://www.key-
sight.com/go/conformity and type in the
product number in the Search field.
Latest Information
To get the latest firmware/software/elec-
tronic manuals/support information, go to
www.keysight.com and type in the product
number in the Search field at the top of the
page.
PRELIMINARY
Safety Summary
The following general safety precautions must be observed during all phases of
operation, service, and repair of this instrument. Failure to comply with these precautions
or with specific warnings elsewhere in this manual may impair the protections provided
by the equipment. In addition, it violates safety standards of design, manufacture, and
intended use of the instrument. Keysight Technologies assumes no liability for
customer’s failure to comply with these requirements.
•GROUND THE INSTRUMENT
This is Safety Class I instrument. To minimize shock hazard, the instrument chassis
and cabinet must be connected to an electrical ground. The power terminal and the
power cable must meet International Electrotechnical Commission (IEC) safety
standards.
•DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE
Do not operate the instrument in the presence of flammable gases or fumes.
Operation of any electrical instrument in such an environment constitutes a definite
safety hazard.
•KEEP AWAY FROM LIVE CIRCUITS
Operation personnel must not remove instrument covers. Component replacement
and internal adjustments must be made by qualified maintenance personnel. Do not
replace components with power cable connected. Under certain conditions,
dangerous voltages may exist even with the power cable removed. To avoid injuries,
always disconnect power and discharge circuits before touching them.
•DO NOT SERVICE OR ADJUST ALONE
Do not attempt internal service or adjustment unless another person, capable of
rendering first aid and resuscitation, is present.
•DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT
Because of the danger of introducing additional hazards, do not install substitute
parts or perform any unauthorized modification to the instrument. Return the
instrument to a Keysight Technologies Sales and Service Office for services and repair
to ensure that safety features are maintained.
•DANGEROUS PROCEDURE WARNINGS
Warnings, such as example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed.
WARNING Dangerous Voltage, capable of causing death, are present in this instrument. Use
extreme caution when handling, testing, and adjusting.
Safety Symbols
The general definitions of safety symbols used on equipment or in manuals are listed
below.
Instruction manual symbol. The equipment will be marked with this symbol when it is
necessary for the user to refer to the instruction manual.
Hazardous voltage and potential for electrical shock. Do not touch terminals that have
this symbol when the equipment is on.
Protective conductor terminal. For protection against electrical shock in case of a fault.
Used with field wiring terminals to indicate the terminal which must be connected to
ground before operating equipment.
Frame or chassis terminal. A connection to the frame (chassis) of the equipment which
normally includes all exposed metal structures.
Grounded terminal which indicates the earth potential.
Direct current.
Alternating current.
On supply.
Off supply.
Standby supply. The equipment will be marked with this symbol is not completely
disconnected from AC mains when power switch is in the standby position.
IEC Measurement Category I
WARNING The warning sign denotes a hazard. It calls attention to a procedure, practice, condition
or the like, which, if not correctly performed or adhered to, could result in injury or
death to personal.
CAUTION The caution sign denotes a hazard. It calls attention to an operating procedure, practice,
condition or the like, which, if not correctly performed or adhered to, could result in
damage to or destruction of part or all of the equipment.
>
`
^
CAT I
Product Stewardship
Waste Electrical and Electronic Equipment (WEEE)
The crossed out wheeled bin symbol indicates that separate collection for waste electric
and electronic equipment (WEEE) is required, as obligated by the EU DIRECTIVE and other
National legislation.
Please refer to http://keysight.com/go/takeback to understand your Trade in options with
Keysight in addition to product takeback instructions.
User's Guide
2 Keysight 16442B User’s Guide, Edition 3
User's Guide
Keysight 16442B test fixture (B1500A-A5F) is designed for testing electronic
devices. You mount the suitable socket module on the 16442B, which allows you to
easily connect various devices (DUTs) to measurement units.
The 16442B has thirteen channels:
• Six source/monitor unit (SMU) channels
Up to three channels can be connected to SMUs by Kelvin connections.
• Two voltage source unit (VSU) channels
• Two voltage monitor unit (VMU) channels
• Two pulse generator unit (PGU) channels
• One ground unit (GNDU) channel
This manual contains the following sections:
•“Introduction”
•“Operation”
•“Installation”
•“Maintenance”
•“Specifications”
•“Options”
Keysight 16442B User’s Guide, Edition 3 3
User's Guide
Introduction
Introduction
Keysight 16442B test fixture (B1500A-A5F) contains the following accessories:
Description Keysight
Part Number Quantity
Test fixture 16442-60011 1
Stabilizer set (with flathead screws) 16442-60002 1
Carrying case for socket modules 16442-60142 1
Miniature banana to pin plug connection cable
(black)
16442-61600 4
Miniature banana to pin plug connection cable
(red)
16442-61601 4
Miniature banana to pin plug connection cable
(blue)
16442-61602 4
Pin plug to pin plug connection cable (black) 16442-61603 3
Pin plug to pin plug connection cable (red) 16442-61604 3
Pin plug to pin plug connection cable (blue) 16442-61605 3
4 Keysight 16442B User’s Guide, Edition 3
User's Guide
Introduction
NOTE Inspecting the 16442B upon Receiving
When the 16442B test fixture (B1500A-A5F) arrives at your site, make sure that
nothing is missing or damaged. Unpack the carton, then check the contents against
figure and table above. For details about furnished and optional accessories, refer to
“Specifications”.
If anything is missing or damaged, contact your nearest Keysight Technologies sales
office.
Miniature banana to miniature clip connection
cable (black)
16442-61606 3
Miniature banana to miniature clip connection
cable (red)
16442-61607 3
Miniature banana to miniature clip connection
cable (blue)
16442-61608 3
Miniature banana to miniature banana connection
cable (black)
16442-61609 3
Miniature banana to miniature banana connection
cable (red)
16442-61610 3
Miniature banana to miniature banana connection
cable (blue)
16442-61611 3
Blank PTFE
board 16058-60004 1
Dual-in-line package socket module (28-pin) 16088-60042 1
Universal socket module, 0.075 inch pitch 16442-60051 1
Universal socket module, 0.05 inch pitch 16442-60052 1
Connection pin set (10 ea.) 16088-60013 2
User’s Guide (this document) 16442-90100 1
Description Keysight
Part Number Quantity
Table des matières
Autres manuels Keysight Équipement de test
Keysight
Keysight M8000 Series Manuel utilisateur
Keysight
Keysight N7026A Manuel utilisateur
Keysight
Keysight TS-5400 Mode d'emploi
Keysight
Keysight 1000B Series Manuel utilisateur
Keysight
Keysight N5242-60124 Manuel utilisateur
Keysight
Keysight E6640A Manuel utilisateur
Keysight
Keysight 16048D Manuel d'utilisation
Keysight
Keysight DSO1000B Series Manuel technique
Keysight
Keysight 42030A Manuel d'utilisation
Keysight
Keysight 90000 X Series Manuel utilisateur
Keysight
Keysight 85056A Manuel
Keysight
Keysight InfiniiVision 4000 X Series Manuel utilisateur
Keysight
Keysight InfiniiVision EDUX1002A Manuel utilisateur
Keysight
Keysight 85053A Manuel
Keysight
Keysight 11683A Manuel de service
Keysight
Keysight Infiniium 9000 Series Manuel utilisateur
Keysight
Keysight PXB MIMO Receiver Tester Manuel du propriétaire
Keysight
Keysight 6 Series Manuel utilisateur
Keysight
Keysight InfiniiVision 4000G X Series Manuel utilisateur
Keysight
Keysight M8000 Series Manuel utilisateur
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
