Keysight Technologies 81133A Manuel utilisateur
4Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015
Important Notice
© Keysight Technologies 2005, 2019
Manual Part Number
5988-7401EN
Revision
April 2019
Printed in Germany
Keysight Technologies
Herrenberger Straße 130
D-71034 Böblingen
Germany
Authors: Keysight Technologies
Warranty
The material contained in this document is
provided "as is," and is subject to being changed,
without notice, in future editions. Further, to the
maximum extent permitted by applicable law,
Keysight disclaims all warranties, either express
or implied, with regard to this manual and any
information contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a particular
purpose. Keysight shall not be liable for errors or
for incidental or consequential damages in
connection with the furnishing, use, or
performance of this document or of any
information contained herein. Should Keysight
and the user have a separate written agreement
with warranty terms covering the material in this
document that conflict with these terms, the
warranty terms in the separate agreement shall
control.
Technology Licenses
The hardware and/or software described in this
document are furnished under a license and may
be used or copied only in accordance with the
terms of such license.
Restricted Rights Legend
If software is for use in the performance of a U.S.
Government prime contract or subcontract,
Software is delivered and licensed as
"Commercial computer software" as defined in
DFAR 252.227-7014 (June 1995), or as a
"commercial item" as defined in FAR 2.101(a) or
as "Restricted computer software" as defined in
FAR 52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is subject to
Keysight Technologies' standard commercial
license terms, and non-DOD Departments and
Agencies of the U.S. Government will receive no
greater than Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Government
users will receive no greater than Limited Rights
as defined in FAR 52.227-14 (June 1987) or DFAR
252.227-7015 (b)(2) (November 1995), as
applicable in any technical data.
Safety Notices
A CAUTION notice denotes a hazard. It calls
attention to an operating procedure, practice, or
the like that, if not correctly performed or adhered
to, could result in damage to the product or loss
of important data. Do not proceed beyond a
CAUTION notice until the indicated conditions
are fully understood and met.
A WARNING notice denotes a hazard. It calls
attention to an operating procedure, practice, or
the like that, if not correctly performed or adhered
to, could result in personal injury or death. Do not
proceed beyond a WARNING notice until the
indicated conditions are fully understood and
met.
CAUTION
WARNING
Contents
Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015 5
Contents
Contents 5
Safety Requirements 9
Safety Summary 9
Environmental Conditions 9
Before Applying Power 10
Ground the Instrument 10
Do not Operate in an Explosive Atmosphere 10
Do not Remove the Instrument Cover 10
Initial Inspection 11
Power Requirements 12
Performance Requirements 12
Ventilation Requirements 12
Cleaning Recommendation 13
Declaration of Conformity 14
Introduction to the Keysight 81133A/81134A Pulse Generator 15
Benefits and Key Features 16
Front Panel Overview 17
Input and Outputs 18
Rear Panel Overview 20
Operating the Keysight 81133A/81134A Pulse Generator 21
Navigation through the Pages 22
How to Navigate through the Parameters at one Page 23
How to Select a Parameter from a Selection List 23
How to Change a Number Field 25
Setting Up Generic and Advanced Signals 29
Setting Up a Clock Signal 30
Using the Graphical User Interface 31
Contents
6 Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015
Using the Remote Programming Interfaces 37
Setting Up a Pulse Signal 38
Using the Graphical User Interface 38
Using the Remote Programming Interfaces 41
Setting Up a Data Pattern 42
Using the Graphical User Interface 42
Using the Remote Programming Interfaces 47
Setting Up a Burst Signal 48
Using the Graphical User Interface 48
Using the Remote Programming Interfaces 53
Setting Up a Repetitive Burst Signal 54
Using the Graphical User Interface 54
Using the Remote Programming Interfaces 59
Setting Up Signals for a Stressed Eye Diagram
Measurement 60
Connecting the Instruments 61
Setting Up the 81134A by Using the Graphical User Interface 62
Setting Up the 33250A Waveform Generator 65
Viewing the Eye Diagram on the 86100 DCA 65
Play with the Settings 66
Using the Keysight 81133A/81134A Pulse Generator 67
Pages of the User Interface 68
Combining Parameters for Signal Generation 70
Instrument Modes 70
Pattern Modes 72
Signal Modes 73
Variable Crossover 74
Clock Sources 75
Start Mode 77
Trigger Out 77
Timing of Generated Signals 78
Clock 79
Pulses 80
Data Pattern 81
PRBS 82
Started Burst 83
Contents
8 Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015
Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015 9
Safety Requirements
The following general safety precautions must be observed during
all phases of operation of this instrument. Failure to comply with
these precautions or with specific warnings elsewhere in this
manual violates safety standards of design, manufacture, and
intended use of the instrument.
Keysight Technologies assumes no liability for the customer's
failure to comply with these requirements.
Before operation, review the instrument and manual for safety
markings and instructions. You must follow these to ensure safe
operation and to maintain the instrument in safe condition.
Safety Summary
This product is a Safety Class 1 instrument (provided with a
protective earth terminal). The protective features of this product
may be impaired if it is used in a manner not specified in the
operation instructions.
All Light Emitting Diodes (LEDs) used in this product are Class 1
LEDs as per IEC 60825-1.
Environmental Conditions
This instrument is intended for indoor use in an installation
category II, pollution degree 2 environment. It is designed to
operate within an operating temperature range of 0 – 55 °C (32 –
130 °F) at a maximum relative humidity of 95% and at altitudes of
up to 2000 meters.
Refer to the specifications tables for the ac mains voltage
requirements and ambient operating temperature range.
Safety Requirements Safety Summary
10 Keysight 81133A/81134A Pulse Generator User’s Guide, April 2015
Before Applying Power
Verify that all safety precautions are taken.
The power cable inlet of the instrument is used to disconnect the
instrument from the mains in case of hazard. The instrument must
be positioned so that the operator can easily access the power
cable inlet.
When the instrument is mounted in a rack, the rack must be
provided with an easily accessible mains switch.
Ground the Instrument
To minimize shock hazard, the instrument chassis and cover must
be connected to an electrical protective earth ground. The
instrument must be connected to the ac power mains through a
grounded power cable, with the ground wire firmly connected to
an electrical ground (safety ground) at the power outlet. Any
interruption of the protective (grounding) conductor or
disconnection of the protective earth terminal will cause a
potential shock hazard that could result in personal injury.
Do not Operate in an Explosive Atmosphere
Do not operate the instrument in the presence of flammable gases
or fumes.
Do not Remove the Instrument Cover
Operating personnel must not remove instrument covers.
Component replacement and internal adjustments must be made
only by qualified personnel.
Instruments that appear damaged or defective should be made
inoperative and secured against unintended operation until they
can be repaired by qualified service personnel.
General operation advises the mains supply voltage fluctuations
are not to exceed 10% of nominal supply voltage
Autres manuels pour 81133A
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Keysight Technologies Onduleur
Keysight Technologies
Keysight Technologies Y1165A Manuel utilisateur
Keysight Technologies
Keysight Technologies P9336A Guide de l'utilisateur
Keysight Technologies
Keysight Technologies E8257D Manuel utilisateur
Keysight Technologies
Keysight Technologies E4360A Manuel utilisateur
Keysight Technologies
Keysight Technologies N5991 Manuel utilisateur
Keysight Technologies
Keysight Technologies 81160A Manuel utilisateur
