Key Digital KD-IP1080Tx Manuel utilisateur

1 | P a g e

Verified Network Switches for use with

Key Digital Enterprise AV –HD over IP Systems

Supported Models:

4K Systems:

KD-IP922ENC, KD-IP922DEC

1080p Systems:

KD-IP1080Tx, KD-IP1080Rx

KD-IP120Tx, KD-IP120Rx, KD-IP120POETx, KD-IP120POERx

Important Note:

Setup is different for 4K (KD-IP922) and 1080p (KD-IP1080, KD-IP120) systems.

There are separate setup instructions for each where applicable.

1. Supported Models and System Facts Pg. 2

2. Network Switch Requirements for Enterprise AV Pg. 3

3. Verified Network Switches Table Pg. 4

4. Araknis Setup for 1080p Systems Pg. 6

5. Araknis Setup for 4K Systems Pg. 11

6. Cisco Setup for 1080p Systems Pg. 16

7. Cisco Setup for 4K Systems Pg. 24

8. D-Link Setup for 4K and 1080p Systems Pg. 38

9. Engenius IGMP Setup for 1080p Systems Pg. 46

10. Linksys IGMP Setup for 1080p Systems Pg. 50

11. Linksys IGMP Setup for 4K Systems Pg. 56

12. Netgear IGMP Setup for 4K and 1080p Systems Pg. 65

13. Pakedge S3 IGMP Setup for 4K and 1080p Systems Pg. 70

14. Pakedge SX Series IGMP Setup for 4K and 1080p Systems Pg. 75

15. Titan Networx IGMP Setup for 1080p Systems Pg. 80

16. Wifi Router Setup and Requirements Pg. 88

2 | P a g e

Supported Models:

Key Digital Enterprise AV product family consists of many different models. Not all models are compatible together

System Facts

KD-IP922 models (4K System)

Video Compression Standard: Motion JPEG 2000

Data Stream Bandwidth: < 900 Mbps

Stream Resolution

Bandwidth

4K @ 60Hz/30Hz

≤ 850 Mbps

1080p @ 60Hz

≤ 250 Mbps

1080i / 720p @ 60Hz

≤ 125 Mbps

Latency: ≈ 40ms @4K. Less at lower resolutions.

PoE Power Consumption: ≤ 9 Watts per unit

Required network cabling: CAT6 UTP/STP, CAT6A, CAT7

KD-IP1080, KD-IP120 models (1080p System)

Video Compression Standard: H.264

Data Stream Bandwidth: < 15 Mbps

Stream Resolution

Bandwidth

1080p @ 60Hz

≤ 15 Mbps

1080i / 720p @ 60Hz

≤ 12 Mbps

480p @ 60Hz

≤ 4 Mbps

Latency: ≈ 400ms @1080p. Less at lower resolutions.

PoE Power Consumption: ≤ 6 Watts per unit

Required network cabling: CAT5e UTP/STP, CAT6 UTP/STP, CAT6A, CAT7

3 | P a g e

Network switch Requirements for Enterprise AV

Key Digital’s Enterprise AV is an HDMI over IP system that utilizes multicasting technology to broadcast streams

throughout the network.

Enterprise AV requires a network switch with IGMP (Internet Group Management Protocol) support in order to

direct traffic of the broadcasted streams, ensuring that only the desired decoders receive the stream from the

selected encoder.

For 1080p systems (KD-IP1080, KDIP120 models) that plan to use the video preview feature of the Key Digital App,

IGMP v3 must be enabled. For 1080p or 4K systems that will not use the video preview feature, IGMP v2 is enabled.

KD-IP922 systems require the following IP addresses to be reserved. They cannot be assigned to KD-IP922 units:

192.168.1.1, 192.168.1.50, 192.168.1.90, 192.168.1.100, 192.168.1.150, 192.168.1.200

Feature

4K System (KD-IP922 models)

1080p System

(KD-IP1080, KD-IP120 models)

IGMP v2

X (for non-video preview systems)

IGMP v3

X (for video preview systems)

Bandwidth

1Gbps

100BaseT

8K Jumbo Frame

PoE

Optional

Optional (excl KD-IP120PoE models)

4 | P a g e

Verified Network Switches

Brand

Model

Port

Number

PoE

KD Lab Verified

KD-IP1080/120

KD Lab Verified

KD-IP922

Araknis

AN-210-SW-R-8-

POE

YES

AN-210-SW-F-8-

POE

YES

AN-210-SW-R-16-

POE

YES

AN-210-SW-F-16-

POE

YES

AN-210-SW-R-24-

POE

YES

AN-210-SW-F-24-

POE

YES

AN-210-SW-F-48-

POE

YES

AN-310-SW-R-8

AN-310-SW-F-8

AN-310-SW-R-16

AN-310-SW-F-16

AN-310-SW-R-24

AN-310-SW-F-24

YES

AN-310-SW-R-8-

POE

YES

AN-310-SW-F-8-

POE

YES

AN-310-SW-R-16-

POE

YES

AN-310-SW-F-16-

POE

YES

AN-310-SW-R-24-

POE

YES

AN-310-SW-F-24-

POE

YES

AN-310-SW-F-48-

POE

YES

Cisco

SF500-48

YES

Catalyst 3850

Series

YES

5 | P a g e

Brand

Model

Port

Number

PoE

KD Lab Verified

KD-IP1080

KD Lab Verified

KD-IP922

D-Link

DGS-3630-52PC

Yes

YES

DGS-3630-52TC

DGS-3630-28PC

YES

DGS-3630-28SC

DGS-3630-28TC

Engenius

EGS5212P

YES

EGS7228FP

YES

EGS7252FP

YES

EWS1200D-10T

EWS1200D-28T

EWS1200D-52T

EWS5912FP

YES

EWS7928P

YES

EWS7928FP

YES

EWS7952FP

YES

Linksys

LGS552P

YES

LGS528P

YES

LGS326P

YES

LGS318P

YES

LGS326MP

YES

LGS326P

YES

LGS326

LGS318P

YES

LGS318

LGS308MP

YES

LGS308P

YES

LGS308

6 | P a g e

Brand

Model

Port

Number

PoE

KD Lab Verified

KD-IP1080

KD Lab Verified

KD-IP922

Netgear

GS716T

GS724T

GS748T

YES

GS752TP

YES

GS728TP

YES

Pakedge

S3L-24P

YES

SX-8EP

SX-8P

YES

SX-24

SX-24P8

YES (8)

SX-24P16

YES

(16)

SX-24P

YES

(24)

Titan

Networx

TNSS2400P

YES

7 | P a g e

IGMP Setup Guide: Araknis

1080p Systems (KD-IP1080, KD-IP120)

1. Before Araknis network switch is configured Key Digital KD-IP120/KD-IP1080 HDMI switch set must be

connected to all HDMI sources/displays/network switches, and configured using Key Digital KD-IP120 Key

Digital Management Software latest version; refer to Key Digital KD-IP120/KD-IP1080 configuration manual.

2. Power-up all the system components. Using Key Digital KD-IP120 Key Digital Management Software, switch

All Outputs -> Through at switching page.

3. IMPORTANT: Disconnect all the DHCP devices like routers, servers from the Araknis network switch.

4. Locate a pinhole “RESET” button at the front panel left bottom corner of your Araknis network switch. Using

a paper clip press and hold a reset button for more than 10 seconds and then release. Wait while the device

is restarted and ready to use (about 5min).

5. IMPORTANT: At this point all the displays should be displaying distorted randomly flashing video images.

6. Connect your PC to the Araknis network switch directly using a network cable.

7. If you have not done yet, configure your PC’s IP address to the same range as the switch (default

192.168.20.xxx).

8. Enter the switch’s IP address (default is 192.168.20.254) in your browser and press ENTER.

9. Enter user name and password (default is “araknis” for both). Then click Log In.

8 | P a g e

10. Navigate to Settings -> System. Under IP Address Settings elect Static. Change an IP address to

192.168.1.251, Subnet Mask to 255.255.255.0, Default Gateway to 192.168.1.1 (in this case), and at the

bottom click Apply. If you are setting up multiple network switches it is recommended to set first one to

192.168.1.251, second to 192.168.1.252, and so on, and each switch must be set individually same way as

described below.

9 | P a g e

11. Page will refresh. Configure your PC’s IP address to the same range as the switch (default 192.168.1.xxx).

Enter the switch’s IP address (default is 192.168.1.251) in your browser and press ENTER.

12. Make sure the settings remain as above.

13. Navigate to Advanced -> Multicast -> IGMP Snooping. Under Settings select Enable for Status, V3 for

Version, and Enable for Report Suppression. Under VLAN Settings / VLAN ID 1 select Enable for IGMP

Snooping Status and Enable for Fast Leave. Under Querier Settings / VLAN ID 1 select Enable for Querier

State, V3 for Querier Version and make sure all other setting are exactly as shown below. Click Apply.

10 | P a g e

14. IMPORTANT: At this point all the displays should be displaying stable running video from the selected

sources. If you do not have them displaying properly, than network switch is configured incorrectly.

15. Navigate to Maintenance -> Restart Device and click Restart Switch. After switch is rebooted and back to

normal log in again, check all the settings again.

Autres manuels pour KD-IP1080Tx

Ce manuel convient aux modèles suivants

Autres manuels Key Digital Changer

Key Digital

Key Digital KD-HDMI2X1 Manuel utilisateur

Key Digital

Key Digital KD-HDMI4X1 Manuel utilisateur

Key Digital

Key Digital Black Bull KD-HDRV2X1 Manuel utilisateur

Key Digital

Key Digital KD-S2x1 Manuel utilisateur

Key Digital

Key Digital KD-CATHD150 Manuel utilisateur

Key Digital

Key Digital KD-CSW4X1 Manuel utilisateur

Key Digital

Key Digital Pro Series Manuel utilisateur

Key Digital

Key Digital FatCAT Rx KD-4AUVRX Manuel utilisateur

Key Digital

Key Digital KD-HDMI2X8P Manuel utilisateur

Key Digital

Key Digital KD-Pro4x1X Manuel utilisateur

Key Digital

Key Digital KD-SW4x1 Manuel utilisateur

Key Digital

Key Digital KD-HDMI2X1 Manuel utilisateur

Key Digital

Key Digital KD-X200ProK Manuel utilisateur

Key Digital

Key Digital Phantom KD-HDSW2x1Pro Manuel utilisateur

Key Digital

Key Digital KD-HDMI2X1 Manuel utilisateur

Key Digital

Key Digital KD-VPHD4X1 Manuel utilisateur

Key Digital

Key Digital KD-PS42 Manuel utilisateur

Key Digital

Key Digital KD-HDMI4X1 Manuel utilisateur

Key Digital

Key Digital KD-X4x1WUTx Manuel utilisateur

Key Digital

Key Digital KD-2x1CSK Manuel utilisateur

Key Digital

Key Digital X4x1WUTx Manuel utilisateur

Key Digital

Key Digital KD-22HUCPro Manuel utilisateur

Key Digital

Key Digital KD-SX440WP Manuel utilisateur

Key Digital

Key Digital Phantom KD-HDSW2X1 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur