Kenwood Axcess Manuel utilisateur

How to Connect and Set Up Your Axcess Remote Portal 1

How to Connect and Set Up Your New Axcess

Welcome to the Connection and Setup Guide for your new Kenwood Axcess. With Axcess, you can enjoy

Internet Radio and the music stored in your Entré library anywhere in your home. Axcess doesn’t require

extensive setup—with a few simple connections, you’ll be able to access your media remotely.

OpenGlobe, the OpenGlobe logo, CE-Commerce and entertain simplicity are trademarks of

OpenGlobe, Inc.

CDDB is a registered trademark of GraceNote.

All other trademarks are property of their registered owners.

What’s Included with Axcess?

How Do I Use Axcess Safely?

Read this section carefully to ensure safe operation.

The Kenwood Axcess is designed for operation only on AC 120V current. Axcess must be connected to a 120V

AC outlet that supplies constant voltage. Do not use an outlet controlled by a switch, or the switched power

outlet on a receiver or other audio component.

Prevent electric shock:

•Do not expose your Axcess to rain or moisture.

•Do not remove the cover.

There are no user-serviceable parts inside. If your Axcess requires

repair, take it to an authorized service outlet.

The icon to the left indicates the presence of un-insulated

dangerous voltage that may be of sufficient magnitude to cause

electric shock.

Remote

Batteries

Unpack your new Axcess carefully and make sure you have all the

accessories:

Phone cord

How to Connect and Set Up Your New Axcess

2 How to Connect and Set Up Your Axcess Remote Portal

Resetting Axcess

If Axcess fails to respond to front panel or remote commands, or if it responds erroneously, reset it:

1. Hold the POWER ON button down on the remote control until the Standby, MUSIC, NET RADIO, AUX and

OG lights flash momentarily. Then release the POWER ON button.

2. When the Standby light stays lit, press the POWER ON button on the remote or the POWER button on the front

panel to turn Axcess on.

How Do I Connect Axcess to Entré and the Internet?

Because Axcess is designed to play back content MP3s from Entré or Internet Radio via Entré, you must connect

Axcess to Entré, either via a common telephone line or directly. Since Axcess connects to the Internet through

Entré, the way you set up Entré’s Internet connection affects how Internet Radio works on Axcess. There are two

ways to connect Entré to the Internet:

• Dial-up, via Entré’s internal modem

• Broadband (through DSL, a cable modem, or other high-speed connection)

To learn more about connecting Entré to the Internet, see “How Do I Connect My Entré to the Internet?” on

page 17 of How to Connect and Set Up Your Entré Entertainment Hub.

Because there are many different ways to set up a home network, the following connection

diagrams only show the most common ways to connect Axcess and Entré.

Do not plug Axcess’ power cord into a wall outlet until you have completed all the

connections.

Establishing a Connection via Dial-Up

If you use a dial-up connection for Entré, you will not be able to listen to Internet Radio on Axcess. All of Axcess’

other functions will operate normally. Connect the components according to the following illustration:

Entré Dial-Up Internet Connection

How Do I Connect Axcess to Entré and the Internet?

How to Connect and Set Up Your Axcess Remote Portal 3

Establishing a Connection via Broadband

If you use a broadband Internet connection and you connect Entré to the Internet via a Home Phone Network

Alliance (HPNA)/Ethernet bridge, you will be able to use all of Axcess’ functions including Internet Radio.

Connect the components according to the following illustration:

If you use a broadband Internet connection and you connect Entré to the Internet via a Universal Serial Bus

(USB)/Ethernet adaptor and an HPNA/Ethernet bridge, you will be able to use all of Axcess’ functions including

Internet Radio. Connect the components according to the following illustration:

Entré Broadband Internet Connection via HPNA

Entré Broadband Internet Connection via USB

with HPNA/Ethernet Bridge

How to Connect and Set Up Your New Axcess

4 How to Connect and Set Up Your Axcess Remote Portal

The following HPNA/Ethernet bridge models are verified by Kenwood to work with Axcess and Entré:

•D-LinkDHN-100

• LinkSys HPB200

• LinkSys HPR0200

• NetGear PE102

You can purchase an Ethernet adaptor (the CATC NetMate) directly from Kenwood USA. Visit our website at

www.kenwoodusa.com.

You can also make a broadband connection from Entré to the Internet via its USB connector

and an Ethernet adaptor without using an HPNA/Ethernet bridge for Axcess. However, you will

not be able to listen to Internet Radio on Axcess. All of Axcess’ other functions will operate

normally.

Entré Broadband Internet Connection via USB

without HPNA/Ethernet Bridge

(No Internet Radio on Axcess)

How Do I Connect Axcess to My Phone Line?

How to Connect and Set Up Your Axcess Remote Portal 5

How Do I Connect Axcess to My Phone Line?

No matter how your home network is configured, you will connect Axcess to it in the same way.

1. Connect one end of the included telephone cord to the telephone connector labeled WALL on the back of

Axcess.

2. Connect the other end of the telephone cord to the telephone jack on the wall or directly to Entré.

If you have more than one phone line, be sure to connect Axcess to the same phone line that

Entré uses.

How Do I Connect Axcess to My Speakers?

Connect the wires from the left and right

speakers to the speaker connectors on

the back of Axcess.

• Make sure to connect the speaker's

positive (+) terminals to the positive

(+) terminals on Axcess.

Do not allow the + and

- wires to touch (short-

circuit), as this could

damage Axcess.

• The speakers must have a nominal

impedance of more than 6 ohms.

Connecting Axcess to

speakers with a nominal

impedance of less than

6 ohms may cause it to

get too hot. If this

happens, Axcess will automatically reduce its power output until it cools down, causing the

volume to become quieter.

How Do I Set Up My Remote?

1. Remove the cover.

2. Insert two AA batteries, as shown at right.

3. Close the cover.

Axcess Connection to Wall Telephone Jack Axcess Connection Directly to Entré

SUM-2 AA

IECR6, 1.5V

SUM-2 AA

IECR6, 1.5V

AA BATTERY

How to Connect and Set Up Your New Axcess

6 How to Connect and Set Up Your Axcess Remote Portal

How Do I Connect Axcess to an Auxiliary Audio Source?

This is an optional connection. You don’t have to complete it to use Axcess.

You can use the

speakers connected to

Axcess to listen to

sound from another

device (such as your

TV's audio output).

Connect stereo audio

cables from the

device's audio outputs

to Axcess' AUX inputs.

Once you’ve made this

connection, press AUX

on your remote or on the front panel of Axcess to listen to this device. For more information about using Axcess’

auxiliary function, see “How Do I Switch Modes?” on page 6 in How to Use and Enjoy Your Axcess Remote Portal.

Do not connect Axcess' AUX IN and LINE OUT terminals to the same device (such as a tape

recorder). This can create a feedback loop that could damage Axcess and the connected device.

How Do I Connect Axcess to an External Power Amplifier?

You can use

Axcess as the

audio source for

a more powerful

audio system by

connecting it to

an external

power amplifier,

which can then

be used to drive

larger speakers.

Once you've

connected Axcess to the external amplifier, Axcess' volume control will control the volume of the amplifier and the

speakers connected to it.

Connect stereo audio cables from Axcess' LINE OUT outputs to the amplifier's inputs. To connect the amplifier to

the speakers, refer to the amplifier and speaker instruction manuals.

Do not connect Axcess' AUX IN and LINE OUT terminals to the same device (such as a tape

recorder). This can create a feedback loop that could damage Axcess and the connected device.

How Do I Set Up Entré to be Recognized By Axcess?

Once you have connected Axcess and Entré to your network, you need to activate Entré’s secondary network

connection and name the network. Once you do, Axcess will be able to recognize Entré on your network.

1. Press SETUP on the Entré remote.

2. Select INTERNET CONFIGURATION.

3. Select NETWORK CONNECTIONS.

How Do I Power Up Axcess for the Very First Time?

How to Connect and Set Up Your Axcess Remote Portal 7

4. Under SECONDARY NETWORK CONNECTION (LAN), select HOMEPNA.

5. Select SAVE.

6. Select NETWORK NAME.

7. Enter a name for this Entré. (If you have more than one Entré, repeat the process, entering a different name

for each.)

8. Select SAVE.

After changing the network setting and naming the network, you’ll need to reset Entré. See “Resetting Axcess”

on page 2 for more information.

How Do I Power Up Axcess for the Very First Time?

Once you’ve connected Axcess to Entré and your speakers, set up the remote, and set up Entré to recognize

Axcess, you can begin using the Remote Portal. Plug Axcess’ power cord directly into a wall outlet that receives

constant power.

After you plug Axcess’ power cord into the wall, its Standby, Music, Net Radio and AUX indicators illuminate

momemtarily, then it enters Standby mode. Once the Standby indicator stays lit, press the POWER button to turn

Axcess on. Axcess goes through an automatic network configuration, which may include automatically

downloading updated software from Entré. If Axcess finds updated software to download from Entré, the

following screen appears for about 2–3 seconds:

Do not press any buttons on either Axcess’ front panel or remote control until the

configuration process is complete. If you do, Axcess will be unusable because it has no valid

Read-Only Memory (ROM). Return your unit to an authorized service outlet for repair.

Once this process is complete, Axcess enters the AUX input mode. You can then choose to listen to an auxiliary

souce (if connected), or switch to playing music or Internet Radio. For more information about using Axcess, see

“Enjoying Your Music Collection” on page 9 or “Enjoying Internet Radio” on page 13 in How to Use and Enjoy

Your Axcess Remote Portal.

Configuring Axcess Manually

If Axcess is not able to automatically configure the network settings itself or if your network has a static IP

address, Axcess automatically enters the manual configuration mode. You can also choose to manually configure

your Axcess by pressing and holding the select button when the following screen appears:

Network Configuration

Axcess will prompt you to manually enter the network settings (IP address, gateway address, network mask and

DNS address). Get this information from your Internet Service Provider (ISP). If your network uses a static IP

address, you can also get the information directly from your Entré:

1. Press the SETUP button on Entré’s remote.

2. Select INTERNET CONFIGURATION.

How to Connect and Set Up Your New Axcess

8 How to Connect and Set Up Your Axcess Remote Portal

3. Select PRIMARY TCP/IP SETTINGS.

4. Write the settings down or leave Entré set to this screen while you configure Axcess.

Once Axcess enters the manual configuration mode, the IP address appears:

1. Use the left/right arrow buttons to select the number you want to enter (the selected number will blink).

2. Use the up/down arrow buttons to change the number.

3. Repeat steps 1–2 until the correct IP address shows on the display.

4. Once you have entered the correct IP address, press the SELECT button. The gateway address appears:

5. Use the left/right and up/down arrow buttons as before to enter the correct gateway address.

6. Press the SELECT button. The network mask appears. Use the left/right and up/down arrow buttons as before

to enter the correct network mask.

7. Press the SELECT button. The DNS address. appears. Use the left/right and up/down arrow buttons as before

to enter the correct DNS address.

8. Press the SELECT button. “Done?” appears in the top line.

9. If you entered all the network information correctly, press the up or down buttons until the bottom line

reads “Yes” and press the SELECT button.

If you made a mistake entering any of the network information, press the up or down buttons until the bot-

tom line reads “No”, and press the SELECT button. Axcess returns to the network configuration screens.

Repeat steps 1–9.

Manual Media Server (Entré) Selection

Axcess can connect “on the fly” to any Entré connected to your HomePNA network. If you have more than one

Entré on your network, you will need to select which one Axcess should use. You can perform this step at any

time to setup or change which Entré Axcess uses.

Skip this step if you have only one Entré on your network.

1. Hold the SELECT button on Axcess’ front panel down for at least 4 seconds. “Select Server” appears in the

top line of the display, and the name you entered for one of your Entrés appears in the bottom line.

2. Use the up/down arrow buttons so the display’s bottom line shows the name of the Entré you want Axcess

to connect to.

3. Press the SELECT button.

FCC WARNING:

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may

cause harmful interference unless the modifications are expressly approved in the instruction manual. The user

could lose the authority to operate this equipment if an unauthorized change or modification is made.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment may cause

harmful interference to radio communications, if it is not installed and used in accordance with

the instructions. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help

Table des matières

Autres manuels Kenwood Télécommande

Kenwood

Kenwood RC-R0905 Manuel utilisateur

Kenwood

Kenwood RC-R0508 Manuel utilisateur

Kenwood

Kenwood KCA-RC700A Manuel utilisateur

Kenwood

Kenwood Klicker Manuel utilisateur

Kenwood

Kenwood KCA-RC55MR Manuel utilisateur

Kenwood

Kenwood KCA-RC35MR Manuel utilisateur

Kenwood

Kenwood Preset Remote Control Manuel utilisateur

Kenwood

Kenwood KCA-RC01A Manuel utilisateur

Kenwood

Kenwood RC100MR - Marine CD Receiver Remote Control... Manuel utilisateur

Kenwood

Kenwood RC-R0607 Manuel utilisateur

Kenwood

Kenwood KCA-RC405 Manuel utilisateur

Kenwood

Kenwood Excelon KCA-RC800AV Manuel utilisateur

Kenwood

Kenwood KCA-RC107MR Manuel utilisateur

Kenwood

Kenwood GRC-151 Manuel utilisateur

Kenwood

Kenwood KCA-RC406 Manuel utilisateur

Kenwood

Kenwood KNA-RCDV331 Manuel utilisateur

Kenwood

Kenwood Sovereign LCD Remote Control Manuel utilisateur

Kenwood

Kenwood KCA-RC406 Manuel utilisateur

Kenwood

Kenwood KCA-RC107MR Manuel utilisateur

Kenwood

Kenwood RC-R0906 Manuel utilisateur

Kenwood

Kenwood KOS-A200 - Car Audio Expansion Module Manuel utilisateur

Kenwood

Kenwood RC-R0907 Guide de l'administrateur

Kenwood

Kenwood KCA-RC50MR - Marine Wired Remote Control Manuel utilisateur

Kenwood

Kenwood KCA-R6A Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation