Kenmore 625.384610 Manuel utilisateur

OWNER'S MANUAL

Two-Stage

Drinking Water System

MODEL NO. 625.384610

Caution:

Read and follow all safety rules and operating

instructions before first use of this product.

Questions ?

Visit www.KenmoreWater.com

or call toll free 1-800-426-9345 (M - F, 7 AM - 6 PM CST)

Repair or Parts ?Call toll free 1-800-469-4663

See back cover for other Sears service numbers.

SAVE THIS MANUAL

•Warranty

•installation

• How It Works

• Care Of

• Specifications

• Repair Parts

System tested and certified by NSF International

against NSF/ANSI Standard 42.

See performance data sheet for details. ®

Printed on recycled paper

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

PRINTED IN U.S.A. www.KenmoreWater.com Part No. 7293858 (Rev. J 2/8/11)

ONE YEAR FULL WARRANTY ON THE

TWO-STAGE DRINKING WATER FILTER

When installed, operated and maintained according to all instructions supplied with the product, if this Two-

Stage Drinking Water Filter fails due to a defect in material or workmanship within one year from the date

of purchase, call 1-800-4-MY-HOME to arrange for free repair (or replacement if repair proves impossible).

This warranty does not include filter cartridges, which are expendable items.

This warranty applies only while this product is in use in the United States or Canada.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

_'_-- 9-5/8"---_ 4-5/8"

Questions? Call The I<enmore Water Line 1-800-426-9345 or visit I<enmoreWater.com

Unpack and Check Shipment ...................................................................... 4

Plan Your Installation ............................................................................. 5

Step I-Install Supply Water Fitting .................................................................. 6

Step 2-Install Filtered Water Faucet ................................................................. 7

Step 3-Connect Tubes ............................................................................. 8

Maintenance ................................................................................. 9-11

Specifications .................................................................................. 12

Troubleshooting ................................................................................. 12

Exploded View & Parts List ..................................................................... 14-15

•Read all steps and guides carefully before installing

and using your Two-Stage Drinking Water Filter.

Follow all steps exactly to correctly install. Reading

this manual will also help you to get all the benefits

from the Two-Stage Drinking Water Filter.

• Do not attempt to use this product to make safe drink-

ing water from non-potable water sources. Do not use

the system on microbiologically unsafe water, or water

of unknown quality without adequate disinfection

before or after the system.

• Check with your local public works department for

plumbing and sanitation codes. You must follow their

guides as you install the system. Follow your local

codes if they differ with guides in this manual. In

Massachusetts, plumbing codes of Massachusetts shall

be adhered to. Consult with a licensed plumber.

• The Two-Stage Drinking Water Filter works on water

pressures of 30 psi (minimum) to 100 psi (maximum).

If your house water pressure is over the maximum,

install a pressure reducing valve in the water supply

pipe to the Two-Stage Drinking Water Filter.

• Do not install the Two-Stage Drinking Water Filter out-

side, or in extreme hot or cold temperatures.

Temperature of the water supply to the Two-Stage

Drinking Water Filter must be between 40°F and

100°F. Do not install on hot water.

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

INSPECT SHIPMENT

Your Two-Stage Drinking Water Filter is shipped complete

in one carton. Remove all items from your shipping car-

ton.

Check all items against the packing list below. Note any

items lost or damaged in shipment. Note any damage to

the shipping carton. Refer to the exploded view and

parts list in the back of the manual for the part names

and numbers of missing or damaged items. If problems

exist, refer to the website or the toll free number listed

throughout this manual.

Keep the small parts in the parts bag until you are ready

to install them.

NOTE: Codes in the state of Massachusetts require instal-

lation by a licensed plumber.

If you live in the state of Massachusetts, review plumbing

code 248-CMR of the Commonwealth of Massachusetts

before proceeding with the installation.

-F

Two-Stage Drinking Water Filter

3/8" O.D. Tubing

Sump Wrench

Bag Assembly ©

Coin Battery

Mounting Screws

Tee Feed Adaptor

Thread Sealing

Tape

Faucet

Electronics Base

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

PLAN YOUR INSTALLATION

It is recommended to read through the entire manual

before beginning your installation. Follow all steps

exactly. Reading this manual will also help you get all

the benefits from your system.

TYPICAL UNDER SINK LOCATION

The Advanced Two-Stage Drinking Water Filter housing is

normally located under the kitchen and/or bathroom sink,

to filter the cold drinking water. See Figure 2.

CHECK SPACE REQUIREMENTS

Check size and position of items for proper installation

into location chosen.

TOOLS NEEDED

Review the tools needed list. See Figure 1. Gather need-

ed tools before proceeding with the installation. Read

and follow the instructions provided with any tools listed

here.

IMPORTANT: A 1-1/4" alia. hole is needed to mount the

filtered water faucet. To avoid damaging the sink, con-

sult aqualified plumber or installer for drilling proce-

dures in porcelain or stainless steel.

Tools Needed

Phillips Screwdriver Adjustable Wrench

Drill & 1-1/4" bit, if required

Large Adjustable Jaw Pliers or Pipe Wrench

)

Figure 1

Typical Under Sink Installation

filtered water

__faucet

ISINK ::

r_ h mounting

screws (2)

cold water

supply fitting tubing WATER WATER

IN OUT

cold water

NOTE: To change the filter cartridge, turn

off the water and release pressure by

opening the faucet. A nearby shutoff is

convenient. Most sinks already have

shutoff valves on the supply pipes.

Filter I Filter II

NOTE: Allow a minimum space of 1-1/2" under the

system for removing the sumps (to change cartridges). Figure 2

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

CHOOSETYPEOFWATERSUPPLYFITTINGTOINSTALL

Locate the cold water line in the sink cabinet. Check and

comply with local plumbing codes as you plan, and then

install a water supply fitting on the sink's cold water line.

The fitting must provide a leak-tight connection to the

Two-Stage Drinking Water Filter's 3/8" O.D. inlet tubing.

A typical connection using the included water supply fit-

ting is shown in Fig. 3. An alternative connection using

standard plumbing fittings (not included) is shown in Fig. 4.

NOTE: Local code may dictate which type of water fit-

ting is used. Consult aplumber if you are not familiar

with local codes or plumbing procedures.

NOTE: Codes in the state of Massachusetts require

installation by alicensed plumber.

If you live in the state of Massachusetts, review plumb-

ing code 248-CMR of the Commonwealth of

Massachusetts before proceeding with the installation.

A. WATER SUPPLY CONNECTION B. WATER SUPPLY TYPICAL CONNECTION

USING INCLUDED FITTING USING COMPRESSION TYPE FITTING

1. Close the house main water shutoff valve and open

faucets to drain water from the sink's cold water pipe.

2. Remove the nut that connects the cold water faucet to

cold water plumbing.

3. Thread the included water supply fitting onto the pipe

and reconnect nut to bottom of fitting.

cold water included water

faucet stud _ supply fitting

3/8" O.D. yellow

tubing to Water

Filter inlet

wrap outside

threads with

Teflon tape

cold water _

pipe

cold water

shutoff valve

(PARTS NOT INCLUDED)

NOTE: Before starting, be sure to turn off water supply

and open alow faucet to drain the pipe.

Complying with plumbing codes, install a fitting on the

cold water pipe to adapt to 3/8" O.D. tubing. A typical

connection is shown in Figure 4. If threaded fittings are

used, be sure to use pipe joint compound or Teflon tape

on outside threads.

I I I i f_'

II /_ It J

tl It

coldwater

shutoff valve

cold water

pipe

3/8" compression

fitting

_>_ /insert

_/ferrule

_; 3/8. y_llo_w_"__-

tubing to

Water Filter inlet

Figure 3 Figure 4

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

MAKEHOLEFORFAUCET

IMPORTANT: A I-I/4" dia. hole is needed to mount the fil-

tered water faucet. To avoid damaging the sink,

consult aqualified plumber or installer for drilling

procedures in porcelain or stainless steel.

1. Select one of the following options to install the faucet.

Make sure there is room underneath to make the needed

connections.

• Use an existing sink top hole for spray hose or soap dis-

penser (must be 1-1/4" in diameter).

• Drill a new hole in the sink top.

• Drill a hole in the countertop next to the sink.

2. Check to make sure the filtered water faucet base will sit

flat against the mounting surface.

3. If drilling is needed, make a 1-1/4" dia. (minimum) hole for

the faucet in the mounting surface.

INSTALL FAUCET BASE

1. Locate the faucet base (See Fig. 5) and feed the toggle bolts

down through the hole until the faucet base is square against

the mounting surface (sink or countertop). The rubber gasket

should be between the faucet base and mounting surface.

2. Tighten the toggle bolts until the faucet base is firmly

mounted to the surface. Do not overtighten.

CONNECT TUBE TO FAUCET

1. Mount the Two-Stage Drinking Water Filter assembly under

the sink. Allow a minimum of 1-1/2" under the sumps for

changing cartridges (See Fig. 2 on Page 5).

2. Locate the 3/8" O.D. tubing. Refer to the "Connect Tubes"

section on Page 8 and insert one end of the tube all the way

into the 3/8" quick connect fitting on the water OUT side of

the filter assembly. See Figure 6.

3. Feed the other end of the tubing up through the mounting

hole and faucet base. See Figure 6.

4. Refer to the "Cut Tubes to Length" section on Page 8 and

cut the tube square and to length as needed, leaving about

6 inches above the faucet base.

5. Locate the faucet. Refer to the "Connect Tubes" section on

Page 8 and insert the tube all the way into the 3/8" quick

connect fitting on the faucet bottom.

6. Pull on the tube at each end to be sure it is held firmly in

both of the quick connect fittings.

INSTALL FAUCET ON BASE

1. Lower the faucet onto the base. See Figure 7.

2. Give the faucet a 1/4 turn clockwise to attach the faucet to

the base.

3. Install battery in faucet base (See "Change Battery" section

on Page 9) then continue installation with Step 3 on Page 8.

faucet base ___ 1-1/4" dia. hole

rubber gasket ............ L__ through sink or

toggle bolts _ countertop

Figure 5

faucet

faucet base _ Xj_

___ ,_ tubing

filter

assembly

water

OUT

Figure 6

faucet

faucet base

1/4 turn to

connect faucet

to base

Figure 7

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

CONNECT TUBE TO WATER SUPPLY FITTING

1. Locate the remaining piece of 3/8" O.D. tubing. Refer to

the "Connect Tubes" section, below, and insert one end of

the tube all the way into the 3/8" quick connect fitting on

the water IN side of the filter assembly. See Figure 8.

2. Run the other end to the water supply fitting on the cold

water pipe. See Figure 8. Refer to the "Cut Tubes to

Length" section, below, and cut the tube square and to

length as needed.

3. Refer to the "Connect Tubes" section, below, and insert the

tube all the way into the 3/8" quick connect fitting on

included water supply fitting (installed in Step 1).

4. Pull on the tube at each end to be sure it is held firmly in

both of the quick connect fittings.

HOW TO CUT AND CONNECT THE TUBES

Your Two-Stage Drinking Water Filter includes push-in fit-

tings for quick tubing connection. Review the following

instructions before connecting the tubes.

Cut tubes to length

1. Use a sharp cutter or knife to cut the end of tubing.

Always cut the tubing square. See Figure 10.

2. Inspect the end (about 1") of the tubing to be sure there

are no nicks, scratches or other rough spots. If needed,

cut the tubing again.

Connect tubes

NOTE: Remove protective foam plugs before connecting

tubes (See Fig. 9). Discard foam plugs.

1. Push tubing through collet, until it engages the o-ring. See

Figure 11A. Continue pushing until the tube bottoms out

against the back of the fitting. See Figure 11B. A common

mistake is to stop pushing when the tube engages the o-

ring. This will lead to future leaks. When a 3/8" tube is

fully engaged, 3/4" of the tube has entered the fitting.

See Figures 11A & 11B.

2. If using tubing other than tubing supplied with the system,

be sure it is of high quality, exact size and roundness with

a smooth surface.

To disconnect tubes

1. Push the collet inward with a finger tip. See Figure 12.

2. Continue holding collet inward while pulling the tubing

out.

O-Ring Seal _

Co,et

Collet and O-Ring

SINI<II

, ii

cold water

supply fitting

cold water

shutoff filtration

assembly

Push In Fitting

Foam Plug

Remove and Discard Foam Plug

Push In Fitting.N._

Tube

Cut tubing square with end of tubing round,

smooth, with no cuts, nicks or flat spots.

Tube Correctly Cut

Tube Partially Engaged With Fitting

Collet,,_ .O-Ring

Tube Fully Engaged With Fitting

Collet (Depress to

Remove Tubing)

Figure 8

Figure 9

Figure 10

Figure 11A

Figure 11B

Tubing

Figure 13 Disconnect Tubing Figure 12

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

FAUCET ELECTRONICS

Inside the faucet base is a battery operated 6month

timer. See Figure 14.

An amber LED indicator is also located in the front of the

faucet base. This LED will flash continuously after 6

months has passed. This indicates that it is time to

replace the battery and filter cartridges.

CHANGE BATTERY

To change (or install) the battery, complete the following

steps.

1. Loosen the screw on the right side of the faucet base

See Figure 14.

2. Press the battery housing upwards from the front

faucet base until it releases from the faucet base. See

Figure 14.

3. Replace (or install) the battery (Maxell CR 2032 or

equivalent). Place battery into the holder with the pos-

itive (+) side facing the back of the holder.

4. When the battery is first replaced it will flash six times

and turn off. This indicates the battery is fully

charged. After the six flashes, the timer enters the 6

month time cycle.

NOTE: If the LED repeatedly flashes just two times, it is

not a fully charged battery and will need to be replaced.

5. Re-install the timer housing and firmly tighten the

mounting screw. See Figure 14.

battery

housing

batter%

negative (-) ____L_

side facing /_1

the front___ screw

faucet _ L_ _'

base __ Figure 14

Questions? Call The I<enmore Water Line 1-800-426-9345 or visit I<enmoreWater.com

FILTER CARTRIDGE LIFE

It is recommended to replace the battery and filter car-

tridges every 6months of use. There are several vari-

ables that determine how long a cartridge will last. These

include:

1. How much water you use, and

2. How much sediment, taste and/or odor, or other

unwanted substances, are in the water.

Use the following information as a guide. However no

matter which type of cartridge you are using, you will

know it is time to replace it when you first notice the

return of unwanted substances in your water.

Kenmore Two-Stage Drinking Water Filter model

625.384610 with replacement cartridges 42-38480

(Sediment, 5Micron) _ and 42-34373 (Taste & Odor,

Premium) has been tested and certified by NSF

International for the reduction of chlorine taste and odor.

The rated capacity for this system is 4,500 gallons

(17,034 liters) at a rated service flow of 0.6 gpm (gallons

per minute).

OPTIONAL CARTRIDGES

Other filter cartridges are available from Sears to reduce

sediments, tastes and odors, and chemical contaminants.

Following is a list of filter cartridges available:

Sediment Filter Cartridge, 25 MicronS: Sediment car-

tridges reduce sand, silt, clay, dirt and other sediments

from water. Sears Item No. 42-38478 filters the larger

sediments from water, and allows higher flows at less

pressure drop.

Taste and Odor Cartridges: Many bad tastes and/or

odors are reduced from water by an activated carbon

cartridge. It is most often used to reduce chlorine taste

and smell, usually to a single faucet such as the kitchen

cold.

NOTE: Small amounts of hydrogen sulfide (noticeable as

"rotten egg" odor) may be reduced by taste and odor

filters for a short time, quickly exhausting the carbon

media. Consult your Sears store for proper continuous

treatment.

Sears Item No. 42-34370_: For reduction of chlorine

taste and odor.

Sears Item No. 42-34365_: For 99% chlorine reduction,

plus reduction of chemical contaminants.

Sears Item No.42-34377_: For reduction of lead, cysts,

and chlorine taste and odor.

These cartridges have not been performance tested

and certified by NSF International.

_ These cartridges have been performance tested and

certified by NSF International in Model 625.384600.

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

Autres manuels pour 625.384610

Table des matières

Langues :

Autres manuels Kenmore Système d'eau

Kenmore

Kenmore 625.347030 Manuel utilisateur

Kenmore

Kenmore 625.384720 Manuel utilisateur

Kenmore

Kenmore 625.385560 UltraFilter 650 Manuel utilisateur

Kenmore

Kenmore Elite ULTRAFILTER 650 625.38556 Manuel utilisateur

Kenmore

Kenmore 625.384650 Manuel utilisateur

Kenmore

Kenmore 625.347051 Manuel utilisateur

Kenmore

Kenmore 625.3847 Manuel utilisateur

Kenmore

Kenmore 625.384450 Manuel utilisateur

Kenmore

Kenmore ULTRAFILTER 150 625.385700 Manuel utilisateur

Kenmore

Kenmore 625.381560 Manuel utilisateur

Kenmore

Kenmore 625.384650 Manuel utilisateur

Kenmore

Kenmore 625.3845 Manuel utilisateur

Kenmore

Kenmore 625.38156 Manuel utilisateur

Kenmore

Kenmore 153.331020 Manuel utilisateur

Kenmore

Kenmore 625.75130 Manuel utilisateur

Kenmore

Kenmore 625.385010 Manuel utilisateur

Kenmore

Kenmore 625.38575 Manuel utilisateur

Kenmore

Kenmore 625.347050 Manuel utilisateur

Kenmore

Kenmore 625.381560 Manuel utilisateur

Kenmore

Kenmore 625.347051 Manuel utilisateur

Kenmore

Kenmore 625.347001 Manuel utilisateur

Kenmore

Kenmore 625.384540 Manuel utilisateur

Kenmore

Kenmore 625.385010 Manuel utilisateur

Kenmore

Kenmore 625.385560 UltraFilter 650 Manuel utilisateur

Manuels Système d'eau populaires d'autres marques

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur

Microline

Microline T.F.C.-4 Manuel

Eureka Forbes

Eureka Forbes Aquaguard Select Manuel utilisateur

Cetetherm

Cetetherm AquaEfficiency Manuel utilisateur

CB Tech

CB Tech CB-VOC Manuel utilisateur

Vaillant

Vaillant auroFLOW plus VPM 15 D Manuel utilisateur

resideo

resideo Braukmann HS10S Manuel utilisateur

Gude

Gude INOX 100/24 Manuel utilisateur

Mono

Mono Eco 1-60 Manuel

SpectraPure

SpectraPure Drinking Water Kit Manuel utilisateur

HydroCare

HydroCare Dual Action Manuel utilisateur

NEXT pool

NEXT pool STERILOR Cu/Ag Schéma de câblage

Alpha

Alpha SolarSmart 150 Guide de l'utilisateur

TA FRISTAR3 Manuel utilisateur

GÜDE

GÜDE HWA 800 K Manuel utilisateur

Rainfresh

Rainfresh UCS2 Manuel utilisateur