KEENCUT EXCALIBUR 5000 Manuel utilisateur
EXCALIBUR 11000000XX
EXCALIBUR 11000000XXEE
EXCALIBUR 55000000
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUAL DE INSTRUCCIONES
Single language version and parts diagrams can be
down loaded from www.keencut.co.uk
Versionen in den einzelnen Sprachen und Schaubilder der Teile sind
als Download auf www.keencut.co.uk erhältlich.
La version et les schémas des pièces en une seule langue peuvent
être téléchargés depuis www.keencut.co.uk
En www.keencut.co.uk puede descargar versiones en idiomas
individuales y diagramas de piezas.
È possibile scaricare le versioni nelle singole lingue e i disegni delle
parti su www.keencut.co.uk
KC-EX FEB09
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
1 Contents 1
2 Packing list
2.1 Unpacking your machine
3 Assembly
3.1 Adjusting the Legs
3.2 Preparing to fit the Squaring arm
3.3 Fitting the Squaring arm
3.4 Fitting the Wall mounting bracket
3.5 Fitting the Free standing kit
3.6 Fitting the Backing panels
4 Squaring
4.1 Checking your machine for squareness
4.2 Adjusting the squareness
5 Calibration
5.1 Calibrating the vertical square
5.2 Calibrating the Squaring arm scale
5.3 Fitting the Sight-line strip
6 Operation
6.1 Using the Clamp
6.2 The Multi-tool cutter and the Counterbalance – 5000
6.2.1The Cutting blade
6.2.2The Scoring blade
6.2.3The Glass cutter
6.3 The Twin wheel cutter – 5000
7 Maintenance
7.1 General maintenance
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
11. M8 screws
12. Hexagon wrenches
2.0, 2.5, 3.0, 4.0, 5.0, 6.0mm
13. Left hand production stop
14. Spare glass cutting wheel
15. Spare blades
*NOTE: Cutting Head arrangements differ
according to machine type
NOTE: When lifting the main body from the box, DO NOT lift using the black
handles on the cutters.
1. Main body *
2. Squaring arm
3. Left large back panel
4. Left small back panel
5. Right large back panel
6. Right small back panel
7. Wall mounting bracket
8. Measuring rules
9. Spare sight-line strips
10. Plastic rivets
2.1 Unpacking your Machine 2.1
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.1 Assembly 3.1
Adjusting the Legs
NOTE: When lifting the main body from the box do not lift using the black handles on
the cutters.
Remove the Main body from the box and lay it on the floor, remove the packaging from
the bottom end.
1. Slacken the bottom two screws on each leg using the 5mm Hexagon wrench and
extend the telescopic parts to the desired length. (These can be re-adjusted later
before fixing the machine to the wall). Tighten screws firmly to clamp in position.
2. Swing both legs outwards as far as they will go.
The first stages of assembly are carried out with the machine laying on the floor.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.2 Assembly 3.2
Preparing to fit the Squaring Arm
1. Move the lower cutting head to the middle of the Main body.
2. Remove the following:
A. One screw from each leg, using 5mm Hexagon wrench.
B. Two sets of Hexagon headed bolts, washers and nuts from the Main body
using 17mm Spanners.
C. Remove small Screw and two Washers from the back of the squaring arm
using 3mm hexagon wrench.
D. Slide off Right hand production stop (this will need to be replaced further on).
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.3 Assembly 3.3
Fitting the Squaring Arm
1. Slide the Squaring arm in from the left hand side through the gap in the Main
body and align the corresponding screw holes.
2. Fit the two Hexagon bolts from the back of the Main body, fit the washers and
nuts finger tight only.
3. Fit the screws through the Squaring arm * into the leg using the 5mm Hexagon
wrench, do not tighten fully.
4. Fit the two M8 Screws to secure the legs at the top of the Main body using the
6mm Hexagon key, tighten both screws fully. Tighten the other two adjacent
M8 screws.
5. Now tighten fully the screws and nuts as in 2 & 3 above.
6. Replace Right hand production stop, Screw and two Washers using 3mm
hexagon wrench.
* Use holes Aon 122cm (48”) and Bon 160cm (63”) machine.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.4 Assembly 3.4
Fitting the Wall Mounting Bracket
NOTE A: If you are going to fit the Free standing kit (optional) turn to next page.
NOTE B: Ensure the wall is stable and use the appropriate fixings.
Move the lower cutting head to the bottom of the Main assembly.
1. Fit the Wall mounting bracket to the top of the Main body, fasten the screws
finger tight only.
2. Lean the machine against the wall in the desired place.
3. The Wall mounting bracket should lay flush against the wall. Mark the position of
the wall fixings with a short pencil.
4. Move the machine away and remove the Wall mounting bracket.
5. Attach the bracket to the wall in the marked position with appropriate fixings then
reposition and fasten the machine to the bracket.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.5 Assembly 3.5
Fitting the Free Standing Kit (optional)
NOTE: The Free standing kit is an optional extra and does not come packed
with the main machine.
1. Attach the bracket to the top of the machine using the nuts and screws (provided
with the main machine).
Extend the telescopic leg to the same length as the front legs less 12cm (5”)
Assistance will be needed for the following stages
2. Get help to stand the machine up and hold it while the free standing leg is fixed to
the bracket using the 6mm hexagon wrench..
3. Swing down the stay and attach the fixing block to the back of the Main body,
tighten all three screws on the stay (using 5mm & 6mm hexagon wrenches).
4. Extend the telescopic leg so the machine stands evenly as shown.
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
3.61Assembly 3.61
Fitting the Left Backing Panels
1. Remove the screws and nuts from the edge of the Left small back panel.
2. Fit panel into the groove on the top edge of the Squaring arm, slide the panel to
the right and locate the vertical edge into the groove in the Main body. be careful
not to damage the edge of the panel.
3. Fit the Left large back panel into the groove on the top edge of the Squaring arm,
slide it to the right to meet the small panel.
4. Knock in the three Plastic rivets to secure the panel to the leg and fasten the two
panels together with the screws and nuts provided.
3x
2x
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels KEENCUT Coupeur
KEENCUT
KEENCUT EXCALIBUR 1000X Manuel utilisateur
KEENCUT
KEENCUT Javelin Manuel utilisateur
KEENCUT
KEENCUT Evolution3 SmartFold Manuel utilisateur
KEENCUT
KEENCUT Evolution3 SmartFold Manuel utilisateur
KEENCUT
KEENCUT OVAL 6 Manuel utilisateur
KEENCUT
KEENCUT ULTIMAT GOLD Manuel utilisateur
KEENCUT
KEENCUT SteelTrak 165 Manuel utilisateur
KEENCUT
KEENCUT Evolution3 FreeHand Manuel utilisateur
KEENCUT
KEENCUT Evolution 3 SmartFold Manuel d'entretien
KEENCUT
KEENCUT EXCALIBUR 3S Manuel utilisateur
KEENCUT
KEENCUT Evolution3 SmartFold Manuel utilisateur
KEENCUT
KEENCUT Big Bench Manuel utilisateur
KEENCUT
KEENCUT SteelTrak 165 Manuel utilisateur
KEENCUT
KEENCUT Sabre 2 Series Manuel utilisateur
KEENCUT
KEENCUT FPC32 Manuel utilisateur
KEENCUT
KEENCUT Evolution3 FreeHand Manuel utilisateur
KEENCUT
KEENCUT ARTIST Manuel utilisateur
KEENCUT
KEENCUT Evolution3 BenchTop Manuel utilisateur
KEENCUT
KEENCUT Evolution3 SmartFold Manuel utilisateur
KEENCUT
KEENCUT Javelin Integra Manuel utilisateur
