Kanguru Autoloader 100 Manuel utilisateur

Kanguru Autoloader 100

100 Target CD Duplicator

Kanguru Autoloader 100

USER’S GUIDE

This manual applies to v1.16 or later versions of the Kanguru Autoloader 100

Kanguru Autoloader 100

Please be aware of the following points before using the Kanguru Autoloader 100

All other brand or product names are trademarks of their respective companies

or organizations.

Kanguru Solutions will not be held responsible for any illegal use of this product

nor any losses incurred while using this product. The user himself is responsible

for the copyright laws, and is fully responsible for any illegal actions taken.

FCC COMPLIANCE STATEMENTS

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, there is

no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the Distance between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

CUSTOMER SERVICE

To obtain service or technical support for your system, please contact Kanguru

Solutions’ Technical Support Department at 508-376-4245, or visit

www.Kanguru.com for web support.

Kanguru Autoloader 100

Table of Contents:

1. Introduction

2. Reminders

3. Installation and Set Up

3.1 Inspecting the Shipment for Damage

3.2 Unpacking and Verifying Shipment Contents

3.3 Setting Up

3.4 Loading Discs

3.5 Unloading Accepted Discs

3.6 Unloading Rejected Discs

4. Main Functions

4.1 Copy

4.2 Emulate

4.3 Erase

4.4 Autoloader

4.5 Test

4.6 Park

5. Maintenance

5.1 General Maintenance

6. Troubleshooting

6.1 Frequently Asked Questions

6.2 LCD Message Definitions

7. Features and Specifications

7.1 Features

7.2 Specifications

8. Warranty and Tech Support

8.1 Warranty

8.2 Tech Support

Kanguru Autoloader 100

1. Introduction

Thank you for purchasing the Kanguru Autoloader 100 from Kanguru Solutions!

The Kanguru Autoloader 100 is a stand-alone unattended duplicator that requires no

computer connection during operation. It consists of a robotic mechanism that will

automatically move discs from an input bin to the burner, then to the output bin after

recording is finished. If there’s an error in any disc, the robotic arm will pick it up and

drop it in the Reject bin. Low cost and high performance, the Kanguru Autoloader is the

best choice to fulfill your duplication requirements.

2. Reminders

We strongly suggest that you locate your Kanguru Autoloader 100 in a dust free

environment in order to eliminate contamination of discs that cause duplication rejects.

Please also allow enough space around the unit to make sure it can work properly.

The Autoloader 100 DOES NOT support gold CD-R/RWs. Please use silver back

media.

For media selection, we recommend using the branded discs such as Verbatim, TDK,

Sony, Samsung, Ricoh, Maxell, etc., and make sure to reserve some for testing and

possible troubleshooting in the future.

3. Installation and Set Up:

3.1 Inspecting the Shipment for Damage

Your Kanguru Autoloader is supplied in one shipping carton. If the carton shows any

signs of shipping damage you should notify the shipping company immediately. DO

NOT throw away the shipping materials as they may be needed to return your unit if it

needs to be serviced.

3.2 Unpacking and Verifying Shipment Contents

Your Kanguru Autoloader carton contains the following items:

o Kanguru Autoloader

o User’s Guide

o An AC power cord

If any of these items are damaged or missing, please call a tech support technician at

Kanguru Solutions directly at 508-376-4245.

Kanguru Autoloader 100

3.3 Setting Up

Please use the following instructions to setup your Kanguru Autoloader:

1. Remove all parts from the carton. 2. Place the Reject Bin in the unit

3. Attach the sides of the disc hopper by snapping the two sides into place.

4. Attach the base plate to the left side. 5. Attach the output spindle to the base plate

Kanguru Autoloader 100

3.4 Loading Discs

To properly load the disc hopper, place the first disc level on the two white wheels. You

can then drop any additional discs into the hopper once the first disc is stable. The hopper

can initially hold up to 100 discs, but you can add more discs while the system is running.

3.5 Unloading Duplicated Discs

To unload the duplicated discs, tilt the spindle towards the duplicator and pull back.

Always avoid contact with the robotic arm when removing discs.

3.6 Unloading Rejected Discs

All rejected discs are sent to the Reject Bin, which can be pulled out to empty. If you

find that all of your discs are being sent to the reject bin, then your master discs may have

errors. To stop duplication press EXIT and the duplicator will stop once the current disc

has finished.

Kanguru Autoloader 100

4. Main Functions

4.1 COPY

This function will start the duplication process if a master CD and blank CDs are present.

Follow the LCD screen shots below to begin.

1. COPY Press “ENTER” to select the Copy function

1. COPY Autoloader will begin to read the master disc

READ MASTER DISC

[COPY] Use the UP and DOWN arrows to adjust the speed.

SPEED MAX Press ENTER to select desired speed

[SPEED MAX] Press the UP arrow to set the number

COPY NO.Æ121 Press the DOWN arrow to switch places

[SPEED MAX] The LCD will show the number of discs waiting to

COPYINGÆ121 be copied.

[SPEED MAX] The copy has finished and will be moved by the

COPY OK arm.

4.2 Emulate

This function will go through the duplication process, but WILL NOT burn data to the

blank CDs. This will allow you to see if your master CD will duplicate error free. Follow

the LCD screen shots below to begin.

2. EMULATE Press ENTER to select this function

2. EMULATE

READ MASTER DISC

Kanguru Autoloader 100

[EMULATE]

PROCESSING

[EMULATE]

PROCESSING >>

[EMULATE] The LCD will return to 1.COPY after emulate is

EMULATE OK done.

4.3 Erase

This function will erase CDRWs if they have previously been written to. All CDs must be

blank in order to begin the duplication process. Follow the LCD screen shots below to

begin.

3. ERASE Press ENTER to select this function.

[ERASE]

PROCESSING

[ERASE] The disc has been erased and is now ready for

ERASE OK duplication.

4.4 Autoloader

This function will turn the autoloading function on or off. If autoloader is set to NO, then

the unit will function as a 1 to 1 duplicator, without any autoloading abilities. Follow the

LCD screen shots below to begin.

4. AUTOLOADER

Kanguru Autoloader 100

[AUTOLOADER] Use the UP and DOWN arrows to switch between

YES modes. (YES or NO)

4.5 Test

This function will replicate the autoloader’s mechanics. Follow the LCD screen shots

below to begin.

5. TEST

[TEST] The Test function will continue until there are no

PROCESSING blank CDs in the hopper.

4.6 Park

This function will move the robotic arm out of harms way. Use the Park function if you

need to move the autoloader. Press ENTER to select this function.

5. Maintenance

5.1 General Maintenance

To clean the outside cabinet and plastic panels:

o Turn off the power switch and unplug the unit.

o Use a clean lint free cloth moistened with warm water.

o Dry the unit immediately with a clean lint free cloth.

o Store in a dust free environment when not in use.

6. Troubleshooting and FAQ

6.1 Troubleshooting

Q1. If you have a high disc failure rate:

o Try lowering the writing speed and try again.

o The quality of your blank CDs may be poor, try using a higher grade.

o Your master may contain errors or scratches

Kanguru Autoloader 100

Q2. A disc has jammed during operation:

o Please check if the disc is standard size (120mm)

o Please check to see if the discs are level and not warped.

o Make sure your autoloader is on a level surface while in use.

o DO NOT force a disc tray or the robotic arm to remove a disc.

Q3. Discs are not being dropped onto the spindle.

o Make sure the unit is on a level surface.

o Make sure the spindle is properly attached to the base plate

o DO NOT attempt to force the robotic arm into place

Q4. Two or more discs have dropped from the hopper.

o Two discs may have stuck together during the loading process.

o Power down the unit to remove multiple discs.

o Please check to make sure your discs are not out of shape.

6.2 Frequently Asked Questions

Q1. How many discs can the autoloader copy per hour?

A1. The Kanguru Autoloader can copy about 20 full discs per hour.

Q2. Why should the unit’s shipping carton be saved?

A2. In the event that your duplicator needs to be serviced, you will need to send the unit

back in its original packaging, otherwise your warranty may become void.

Q3. What is the purpose of the aluminum tab in the front of the unit?

A3. The aluminum tab stabilizes the CDRW tray as the blank CDs are loaded.

Q4. What should I do if the robotic arm isn’t working properly?

A4. Contact our tech support to assess the situation. 508-376-4245

7. Features and Specifications

7.1 Features

• Standalone duplication: no PC required

• 100 disc capacity

• LCD screen for easy operation

• Auto-detection of reject discs

• 6 Advanced Functions: Copy, Emulate, Erase, Autoloader, Test, Park

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kanguru duplicateur de disques

Kanguru

Kanguru U2-DVDDUPE-S Manuel utilisateur

Kanguru

Kanguru DVD Autoloader 200 Manuel utilisateur

Kanguru

Kanguru U2D2-7 Manuel utilisateur

Kanguru

Kanguru kclone-5hd-twr Manuel utilisateur

Kanguru

Kanguru KCLONE-5HD-SATA Manuel utilisateur

Kanguru

Kanguru KCLONE-1HD-MBC Manuel utilisateur

Kanguru

Kanguru 1.1 Manuel utilisateur

Kanguru

Kanguru KCLONE-4NVME Manuel utilisateur

Kanguru

Kanguru CD Duplicator Manuel utilisateur

Kanguru

Kanguru DVD Duplicator Manuel utilisateur

Kanguru

Kanguru DC-DVDDUPE-S15 Manuel utilisateur

Manuels duplicateur de disques populaires d'autres marques

Riso

Riso CV Series Manuel

MicroBoards Technology

MicroBoards Technology GX-2 Manuel utilisateur

Addonics Technologies

Addonics Technologies HDUS325DX Manuel utilisateur

Carry

Carry Pro118 Manuel utilisateur

CopyPro

CopyPro PowerPro II Manuel utilisateur

Primera

Primera Max Manuel utilisateur

Logicube

Logicube EchoPlus-NG Manuel utilisateur

Silca

Silca Delta 2000 SA Manuel utilisateur

Reflex7

Reflex7 Daisy Chain Series Manuel utilisateur

Vinpower Digital

Vinpower Digital SharkCopier DC Manuel utilisateur

Codonics

Codonics Virtua E Manuel utilisateur

Octave

Octave Copy Master II Manuel utilisateur

StarTech.com

StarTech.com 8STSATDUP11 Manuel utilisateur

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFH7 Manuel utilisateur

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manuel utilisateur

Addonics Technologies

Addonics Technologies CFASTD5 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Manuel utilisateur