K2 Systems Big Foot Manuel utilisateur
k2-systems.com
CONNECTING STRENGTH
Big Foot
QUICK GUIDE
2
Part Number Description
4000218 Big Foot 6" w/ 3"+ Chem Link Clip
Components
Tools overview
Kit includes:
T-Bolt and Hex Nut
Material: stainless steel
13 mm deep socketTorque wrench
T10-50 ft-lbs
Big Foot
Material: aluminum
Optional components:
ChemLink 3" E-Curb Kit
E-Curb
M-1 structural adhesive/sealant
1-Part moisture cure pourable sealant
Chem Link Clip
Material: polymide
3
Assembly
2
!Attach the Chem Link Clip
on the bottom half of the
foot. This is used to ensure
proper distance when
installing the Chem Link
E-Curb. The back of the clip
should hit the wall of the
E-Curb.
1
!Choose the appropriate
fasteners for your structural
attachment. If needed, drill
your pilot holes, seal holes, and
secure the Big Foot to the roof.
4
4
!
Following ChemLink's E-Curb instruction manual, apply 1/4"
beads of M-1 on the inner, middle and outer circle to cover
both sections of the bottom of the E-Curb. Carefully place
the E-Curb ensuring that the inner wall is touching the Chem
Link Clip. Use the ChemLink logo on the E-Curb as a guide to
place the E-Curb directly in front of the bottom of the Big Foot.
Press the rings firmly in place until excess adhesive extrudes
from the outside edges.
3
!Follow ChemLink E-Curb
installation manual for
detailed steps.
Using Chem Link's M-1,
seal the base of the Big
Foot covering the base of
the mount including the lag
screw. M-1 sealant should
coat the entire mount from
the roof to 3" above the top
of the E-Curb rim.
5
5
!Apply M-1 along the outside edge
of the installed E-Curb rings
and smooth it out. Also seal the
connection of the two halves of
the E-Curb.
6
!
Completely fill the E-Curb with ChemLink's
1-Part solution.
6
7
!
The CrossRail can be installed on either side of the Big Foot, but there is a built in shelf for support on the inside of
the Big Foot. To install your CrossRail to the Big Foot, insert the T-Bolt through the slot and into the side channel
of CrossRail. Turn the T-Bolt clockwise ensuring that the mark at the end of the shaft is vertical, indicating proper
alignment. Using a 13 mm socket, tighten to 25.8 ft-lb (35 Nm).
Double check that the alignment marking on the end of the T-Bolt shaft is vertical, indicating proper alignment.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels K2 Systems Support et étagère
K2 Systems
K2 Systems Everest Ground Lug Manuel utilisateur
K2 Systems
K2 Systems 4000142 Manuel utilisateur
K2 Systems
K2 Systems 4000142-B Manuel utilisateur
K2 Systems
K2 Systems Everest CrossRail 44-X Manuel utilisateur
K2 Systems
K2 Systems Splice Foot X Manuel utilisateur
K2 Systems
K2 Systems S-DOME SYSTEM Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
