K Tool International KTI-63250A Manuel utilisateur
OWNER’S MANUAL
50 TON
HYDRAULIC WELDED BOTTLE JACK
KTI-63250A
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Capacity Lifting Range
Min. (inch)
Lifting Range
Max. (inch) Lifting Height
50 TON 11.02” 17.72” 6.7’’
Complies with ASME PASE / 2014 Safety Standards
2
GENERAL SAFETY RULES
Jack use and care
Inspection
GENERAL SAFETY RULES
IMPORTANT SAFETY CONSIDERATIONS
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may
result in serious injury.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator
that common sense and caution are factors that cannot be built into this product, but must be supplied by
the operator.
CAUTION: Do not allow persons to operate or assemble this jack until they have read this manual
and have developed a thorough understanding of how the jack works.
DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL.
To maintain the service jack and user safety, the responsibility of the owner is to read and follow these
instructions.
• Inspect the service jack for proper operation and function.
• Keep instructions readily available for equipment operators.
• Make certain all equipment operators are properly trained; understand how to safely and correctly operate
the unit.
• Allow unit operation only with all parts in place and operating properly.
• Use only genuine replacement parts.
• Service and maintain the unit only with authorized or approved replacement parts; negligence will make the
jack unsafe for use and void the warranty.
• Carefully inspect the unit on a regular basis and perform all maintenance as required.
• Store these instructions in the handle of your jack.
• Keep all decals on the unit clean and visible.
• Inspect the jack carefully before each use. Ensure the jack is not damaged, excessively worn, or missing
parts.
• Do not use the jack unless it is properly lubricated.
• Using a jack that is not in good clean working condition or properly lubricated may cause serious injury.
• Inspect the work area before each use. Make sure it is free and clear of any potential hazards.
• Do not modify the Jack in any way. Unauthorized modication may impair the function and/or safety and
could affect the life of the equipment. There are specic applications for which the Jack was designed.
• Always check for damaged or worn out parts before using the jack. Broken parts will affect the jack
operation. Replace or repair damaged or worn parts immediately.
• Store the jack. When jack is not in use, store it in a secure place out of the reach of children. Inspect it for
good working condition prior to storage and before re-use.
• Not for use by children or people with reduced mental capacity.
• Do not use under the inuence of drugs or alcohol.
• Ensure children and other bystanders are kept at a safe distance when using product.
3
SAFETY MARKINGS
WARNING!
1. Study, understand, and follow all instructions before operating this device.
2. Do not exceed rated capacity.
3. Use only on hard, level surfaces, with less than 3 degrees of slope.
4. Lifting device only. Immediately after lifting, support the vehicle with appropriate means.
5. Do not move or dolly the vehicle while on the jack.
6. Lift only on areas of the vehicle as specied by the vehicle manufacturer.
7. No alterations shall be made to this product.
8. Only attachments and/or adapters supplied by the manufacturer shall be used.
9. Do not get under or allow anyone under the vehicle until it has been supported by jack stands.
10. Center load on saddle prior to lifting.
11. Use wheel chocks or other blocking device on opposing wheels before using jack.
12. Never use on a lawn mower or lawn tractor.
13. Do not use this jack for any use other than the manufacturer specied usage.
14. Do not rock the vehicle while working on or around equipment.
15. The following are not recommended for supporting on this equipment: Foundations, Homes, Mobile
Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc...
16. Failure to heed these markings may result in personal injury and/or property damage.
4
ASSEMBLY
1. Familiarize yourself with the jack. 2. Attach the 2 handle pieces making sure to align
the holes on both sections.
3. Line up the handle to the handle socket located
on the side of the jack. Then insert the handle
inside the handle socket.
4. Secure the handle in place inside the handle
socket. Without any vehicle on the jack. Cycle
the lift up and down several times to insure the
hydraulic system is operating properly. (Perform
the System Air Purge Procedure, Page 5, before
rst use.)
5
SYSTEM AIR PURGE PROCEDURE
IMPORTANT: BEFORE FIRST USE
Perform the following System Air Purge Procedure to remove any air that may have been introduced into
the hydraulic system as a result of product shipment and handling. This step is to be completed without any
weight on the jack.
FIGURE 1 - Typical Bottle Jack
Ram
Saddle
Extension
Screw
Release
Valve
Handle
Sleeve
Handle
Assembly
Oil Plug
(on reservior)
1. Turn release valve counterclockwise on full turn to
the open position.
2. Rapidly pump the handle 6-8 times. Leave handle
in down position to expose oil ll plug.
3. With a at blade screwdriver, push the oil ll plug
slightly to the side to purge trapped air from
system. (Use caution not to tear or puncture the
oil plug.)
4. Turn release valve clockwise to the closed
position.
5. Jack is now ready for use. Check for proper pump
action.
6
7. Before raising the vehicle double check and verify
the saddle is centered and also has full contact
with the lifting point.
RAISING THE JACK
1. Block the vehicle’s wheels for lifting stability.
Secure the load to prevent inadvertent shifting
and movement.
BEFORE USE
1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the
product and the hazards associated with its improper use.
2. Perform the system air purge procedure. (See previous instructions for System Air Purge Procedure.)
3. Check that the pump operates smoothly before putting into service.
4. Inspect before each use. Do not use if bent, broken or cracked components are noted.
8. Pump handle to lift until saddle contacts load.
Continue to pump the jack handle to lift the
vehicle to the desired height. After lifting, support
the load with appropriately rated vehicle support
stands before working on the vehicle.
CAUTION: NEVER WIRE, CLAMP OR
OTHERWISE DISABLE THE LIFT CONTROL
VALVE TO FUNCTION BY ANY MEANS
OTHER THAN BY USING THE OPERATOR'S
HAND. USE THE HANDLE PROVIDED WITH
THIS PRODUCT OR AN AUTHORIZED
REPLACEMENT HANDLE TO ENSURE
PROPER RELEASE VALVE OPERATION. DO
NOT USE EXTENSIONS ON THE AIR HOSE
OR ON THE OPERATING HANDLE.
2. Position the jack near desired lift point.
3. Set the Parking Brake in the vehicle. 4. Refer to the vehicle manufacturer owner’s manual
to locate approved lifting points on the vehicle.
Position the jack so that the saddle is centered
and will contact the load lifting point rmly.
5. Assemble the handle, ensure that spring clips
align with slots.
6. Close the release valve by turning it clockwise
until it is rmly closed.
7
5. After removing jack from under the load, push ram
and handle sleeve down to reduce exposure to
rust and contamination.
LOWERING THE JACK
WARNING: USE EXTREME CAUTION
WHEN LOWERING THE JACK. THE JACK
HANDLE MAY TURN RAPIDLY. OPENING THE
RELEASE VALVE TOO FAST CAN CAUSE
THE JACK TO LOWER RAPIDLY. FAILURE TO
HEAD THESE WARNINGS COULD CAUSE
SERIOUS INJURY OR DEATH.
2. Remove support stands.1. Raise load high enough to allow clearance for the
jack stands to be removed, then carefully remove
jack stands.
3. Grasp the handle rmly with both hands. Securely
hold on to the jack handle so your hands do not
slip and ensure the release valve does not rapidly
lower.
4. Carefully open the Release Valve by slowly
turning the handle counterclockwise. (Do not
allow bystanders around the jack or under the
load when lowering the jack.)
8
MAINTENANCE INSTRUCTIONS
If you use and maintain your equipment properly, it will give you many years of service. Follow the
maintenance instructions carefully to keep your equipment in good working condition. Never perform any
maintenance on the equipment while it is under a load.
Inspection
You should inspect the product for damaged, worn, broken or missing parts (e.g.: pins) and that all
components function before each use. Follow lubrication and storage instructions for optimum product
performance.
Binding
If the product binds while under a load, use equipment with equal or a larger load capacity to lower the load
safely to the ground. After unbinding; clean, lubricate and test that equipment is working properly. Rusty
components, dirt, or worn parts can be causes of binding. Clean and lubricate the equipment as indicated in
the lubrication section. Test the equipment by lifting without a load. If the binding continues contact Customer
Service.
Cleaning
If the moving parts of the equipment are obstructed, use cleaning solvent or another good degreaser to clean
the equipment. Remove any existing rust, with a penetrating lubricant.
Lubrication
This equipment will not operate safely without proper lubrication. Using the equipment without proper
lubrication will result in poor performance and damage to the equipment. Some parts in this equipment are not
self-lubricating. Inspect the equipment before use and lubricate when necessary. After cleaning, lubricate the
equipment using light penetrating oil, lubricating spray.
• Use a good lubricant on all moving parts.
• For light duty use lubrication once a month.
• For heavy and constant use lubrication recommended every week.
• NEVER USE SANDPAPER OR ABRASIVE MATERIAL ON THESE SURFACES!
Rust Prevention:
Check rams and pump plungers on the power unit assemblies daily for any signs of rust or corrosion.
Without a load, lift the equipment as high as it goes and look under and behind the lifting points. If signs of
rust are visible clean as needed.
Grease Fittings
Some models contain grease ttings that will regularly need to be greased and lubricated.
How the Jack Operates
With release valve closed, an upward stroke of the jack handle draws oil from the reservoir tank into the
plunger cavity. Hydraulic pressure holds the valve closed, which keeps the oil in the plunger cavity. A
downward stroke of the jack handle releases oil into the cylinder, which forces the ram out. This raises the
saddle. When the ram reaches maximum extension, oil is bypassed back into the reservoir to prevent an over
extended ram stroke and possible damage to the jack. Opening the release valve allows oil to ow back into
reservoir. This releases hydraulic pressure on the ram, which results in lowering the saddle.
Storing the Jack
1. Lower the Lifting ram.
2. Place the handle in the upright position.
3. Store in a dry location, recommended indoors.
Note: If the jack is stored outdoors, be sure to lubricate all parts before and after use to ensure the jack stays
in good working condition. Always store jack in the fully retracted postion when stored in outdoor or caustic
enviroments that can cause corrosion and/or rust.
9
PARTS BREAKDOWN
10
Ref. Description Qty
1 Roundwire snap ring 1
2 Rectangular ring 2
3O-Ring D85X5.3-G-N 1
4 Piston rod assembly 1
5 Bowl washer 1
6O-Ring D79X5.3-G-N 1
7 Roundwire snap ring 1
8 Base welding parts 1
9 Steel ball 6mm 3
10 Release value assembly 1
11 plastic plug 1
12 Adjusting screw 1
13 Spring 1
14 Spring holder 1
15 Steel ball 3mm 1
16 Ball retaining washer 1
17 Pump plunger assembly 1
18 Oil plug 1
19 Cutter pin 3
20 pin 3
21 Handle socket 1
22 Handle assembly 1
23 Seal kit 1
Table des matières
Autres manuels K Tool International Jack
K Tool International
K Tool International KTI63201 Manuel utilisateur
K Tool International
K Tool International XD KTI-63213A Manuel utilisateur
K Tool International
K Tool International XD KTI63502A Manuel utilisateur
K Tool International
K Tool International KTI-XD63133 Manuel utilisateur
K Tool International
K Tool International KTI-61201 Manuel utilisateur
K Tool International
K Tool International KTI61202 Manuel utilisateur
K Tool International
K Tool International KTI-XD61202 Manuel utilisateur
K Tool International
K Tool International KTI-XD63228 Manuel utilisateur
K Tool International
K Tool International KTI-HD63230 Manuel utilisateur
K Tool International
K Tool International KTI63197 Manuel utilisateur
K Tool International
K Tool International KTI-63505A Manuel utilisateur
K Tool International
K Tool International KTI-63137 Manuel utilisateur
K Tool International
K Tool International HD KTI63194A Manuel utilisateur
K Tool International
K Tool International PRO Series Instructions d'utilisation
K Tool International
K Tool International XD KTI63133 Manuel utilisateur
K Tool International
K Tool International KTI63155 Manuel utilisateur
K Tool International
K Tool International KTI-63103 Manuel utilisateur
K Tool International
K Tool International KTI-XD63213 Manuel utilisateur
K Tool International
K Tool International KTI-HD63155 Manuel utilisateur
K Tool International
K Tool International XD KTI-XD63105 Manuel utilisateur
Manuels Jack populaires d'autres marques
VEVOR
VEVOR TJD-12000SP-F Manuel utilisateur
ULTIMATE SPEED
ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuel utilisateur
Stels
Stels 51131 Manuel utilisateur
Bushranger
Bushranger RJX01 Manuel utilisateur
Clarke
Clarke CTJ2500QLG Manuel d'installation et d'exploitation
Valex
Valex 1650520 Manuel utilisateur
