JVA Z28 Manuel utilisateur
JVA TECHNOLOGIES
www.jva-fence.com
Z28 User ManUal
Page 6 © JVA Technologies Pty. Ltd.
Quick Start Guide
JVA Z28 Manual
1 QUICK START GUIDE
1.1 CHANGING THE PROGRAMMING OPTIONS
Default Installer PIN 012345
Default User PIN 1234
First you have to enter Programming mode.
Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9
Enter Programming Mode Installer Pin * 0 #
When you have entered Programming mode you can begin to enter the following opons to congure your Z28 Se-
curity Energizer. Default Values are highlighted in grey.
Command Key1 Key2 Keys 3 and 4 Key5
Change the Installer
PIN 6 Digits
0 0 Enter the new 6 digit Installer PIN #
High Power Mode
Power Level
0 1 Enter the value in Hundreds of Volts #
Example: to set 8.2kV, use 82 for keys 3 and 4. Default is 85 (8.5kV)
Low Power Mode
Power Level
0 2 Enter the value in Hundreds of Volts #
Example: to set 1.3kV, use 13 for keys 3 and 4. Default is 11 (1.1kV)
Quick Start Guide
JVA Z28 Manual Page 7
Command Key1 Key2 Keys 3 and 4 Key5
Return 1 Fence
Alarm Voltage For
High Power Mode
0 3 Enter the value in Hundreds of Volts #
Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)
Return 2 Fence
Alarm Voltage For
High Power Mode
0 4 Enter the value in Hundreds of Volts #
Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)
Return Fence Alarm
Voltage For Low
Power Mode
0 5 Enter the value in Hundreds of Volts #
Example: to set 0.8kV, use 08 for keys 3 and 4. Default is 05 0.5kV)
Bad/Missed Pulse
Count Before Alarm
Triggers
0 6 Enter the number of Missed Pulses #
Example: to set 14 counts, use 14 for keys 3 and 4. Default is 03
Baery Alarm
Voltage (Volts).
Alarm Value Shown,
Reduced Power is
1V less
0 7 00 01 02 03 04 05 06 07 08 09 #
9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5
Siren On Time
(S=Seconds,
M=Minutes)
0 8 00 01 02 03 04 05 06 07 08 09 #
10S 30S 1M 2M 3M 4M 5M 20M 45M 130M
JVA Z28 Manual
Quick Start Guide
Page 8 © JVA Technologies Pty. Ltd. www.jva-fence.com
Command Key1 Key2 Keys 3 and 4 Key5
Siren O Time
(S=Seconds,
M=Minutes)
0 9 00 01 02 03 04 05 06 07 08 09 #
10S 1M 2M 5M 10M 20M 30M 40M 50M 60M
Siren Cycles 1 0 00 01 02 03 04 05 06 07 08 09 #
012345678 9
Gate Entry/Exit
Delay (S=Seconds,
M=Minutes)
1 3 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M 8M
Chime Mode 1 4 00 01 02 03 04 #
None Door Chime Siren Fence
Alarm
Gate Beeps
Plus Siren
Combined Opons 1
(Add up the op-
ons you want.
E.g. for Max Power
and Limit output:
2 + 4 = 6 Therefore en-
ter 06 for keys 3 and 4
+1 +2 +4 +8 +16 +32 +64 +128 #
N/A Max
Power
2.5J
limit per
zone
N/A Disarm
on
comms
fail
Stop
sending
alarm
memory
Ignore
Low
Baery
Alarm
N/A
An Bridging
Threshold
1 7 Enter in the percentage dierence required to trigger the An-Bridg-
ing alarm. e.g. if you require a 10% change in return voltage to trigger
the alarm, enter 10 for keys 3 and 4. Default is 00 (Disabled)
#
Quick Start Guide
JVA Z28 Manual Page 9
© JVA Technologies Pty. Ltd. www.jva-fence.com
Command Key1 Key2 Keys 3 and 4 Key5
Combined Opons 2
(Like Combined
Opons 1)
1 8 +1 +2 +4 +8 +16 +32 +64 +128 #
Siren
Chirp on
Arm
Enable
Entry
Exit
Gate
4800
Baud
9600
Baud
N/A N/A N/A N/A
Auto Re-arm Time
S=Seconds, M =
Min, D=Disabled
2 0 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M D
Relay 1 2 1 Explained under “1.1.1 Relay Funcons” Default is 09 (Strobe 1) #
Relay 2 2 2 Explained under “1.1.1 Relay Funcons” Default is 13 (Strobe 2) #
Relay 3 2 3 Explained under “1.1.1 Relay Funcons” Default is 08 (Siren) #
Group Mode 2 6 00 01 02 Etc 15 #
No Group Master Slave 1 Slave 14
Input 1 2 7 Default is 00 (N/O Arm/Disarm). See “1.1.2 Input Funcons” #
Input 2 2 8 Default is 16 (N/C Gate 1). See “1.1.2 Input Funcons” #
Input 3 2 9 Default is 17 (N/C Gate 2). See “1.1.2 Input Funcons” #
Exit Programming
Mode
* #
Page 10 © JVA Technologies Pty. Ltd.
Quick Start Guide
JVA Z28 Manual
1.1.1 Relay Funcons
The table below is for use for the relay programming opons menoned in the table on the previous page.
Keys 3
and 4
Funcon Descripon
00 Fence 1 Triggers when Zone 1 is Armed and Return Voltage is below the Threshold Voltage
01 Fence 1 or O Triggers when Zone 1 is Disarmed or Return Voltage is below the Threshold Voltage
02 Armed 1 Zone 1 is Armed
03 Fence 2 Triggers when Zone 2 is Armed and Return Voltage is below the Threshold Voltage
04 Fence 2 or O Triggers when Zone 2 is Disarmed or Return Voltage is below the Threshold Voltage
05 Armed 2 Zone 2 is Armed
07 General Triggers on AC Fail, Tamper, Low Baery/Bad Baery, Gate Alarm or Internal error.
Latched (internal errors only)
08 Siren Triggers on Fence Alarm, Gate or Tamper. Will me out aer the Siren Time Out me.
Latched
09 Strobe Triggers on Fence alarm, Gate or Tamper. Only turns o on Energizer Disarm. Latched
10 AC Fail Triggers on AC Fail
11 Low/Bad Bat-
tery
Triggers on Low or Bad Baery
12 Tamper Triggers when the Tamper Input (if congured) is triggered
14 Gate 1 or 2 Triggers on a Gate Alarm
Quick Start Guide
JVA Z28 Manual Page 11
Keys 3
and 4
Funcon Descripon
15 Siren Caused by
Gate
Behaves like siren, only for Gate Alarms
16 Armed - Low
Power Mode
Triggers when Armed in Low Power mode
17 Group Armed Triggers when group is Armed. Only congurable on group master.
18 Group general Triggers on group general Alarm. Only congurable on group master.
20 Host Control This Relay is completely controlled from a Host system such as Perimeter Patrol or a
Keypad. If the Host system is disconnected from the Energizer for more than 30 sec-
onds, the Relay will automacally change to the Alarm State
21 Host Control -
Not Fail Safe
This Relay is completely controlled from a Host system such as Perimeter Patrol or a
Keypad. If the Host system is disconnected then the Relay will maintain its current state
unl the Host re-connects and requests the relay to change state.
Page 12 © JVA Technologies Pty. Ltd.
Quick Start Guide
JVA Z28 Manual
1.1.2 Input Funcons
Key3 Input Trigger Key4 Input Funcon
0Normally Open (Acve when Closed) 0Arm All Zones when Acve / Disarm otherwise
1Normally Closed (Acve when Open) 1Arm Zone 1 when Acve / Disarm otherwise
2 Momentary Toggle (Toggle between states) 2 Arm Zone 2 when Acve / Disarm otherwise
3NO Pulse Extend (Extend a short Close signal by 3
seconds)
3Low Power when Acve / High Power otherwise.
Requires Energizer to be Armed
4NC Pulse Extend (Extend a short Open signal by 3
seconds)
4Low Power Zone 1 when Acve / High Power
otherwise. Requires Energizer to be Armed
5Low Power Zone 2 when Acve / High Power
otherwise. Requires Energizer to be Armed
6Gate 1 is Open when Acve / Closed otherwise
7Gate 2 is Open when Acve / Closed otherwise
8Tamper Alarm triggered when Acve
9 Pass Through input signal to other device
Quick Start Guide
JVA Z28 Manual Page 13
1.2 SUMMARY OF KEYPAD FUNCTIONS
Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9 Key10
Arm/Disarm USER PIN #
Silence the Energizer Siren 1 4 7 0 #
Enter Programming Mode INSTALLER PIN * 0 #
Enter Keypad Programming Mode INSTALLER PIN * 0 1 #
Exit Programming (Any Mode) * #
Change a User PIN, 4 Digits USER PIN * 0 # [New
PIN]
#
Arm All Zones (Mul-Zone Groups) USER PIN * 1 0 #
Arm Specic Zone (up to Zone 15) USER PIN * 1 Zone Number #
Disarm All Zones USER PIN * 2 0 #
Disarm Specic Zone (up to Zone 15) USER PIN * 2 Zone Number #
Switch to Low Power Mode (All Zones) USER PIN * 4 1 #
Switch Specic Zone to Low Power USER PIN * 4 1 Zone Number #
Switch to High Power Mode (All Zones) USER PIN * 4 2 #
Switch Specic Zone to High Power USER PIN * 4 2 Zone Number #
Arm Gate Zone only USER PIN * 4 #
Bypass Siren (All Zones) USER PIN * 5 2 #
Bypass Specic Zone Siren USER PIN * 5 2 Zone Number #
Page 14 © JVA Technologies Pty. Ltd.
Quick Start Guide
JVA Z28 Manual
Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9 Key10
Re-enable Siren USER PIN * 5 1 #
Re-enable Specic Zone Siren USER PIN * 5 1 Zone Number #
Bypass Gate Alarm (All Zones) USER PIN * 5 4 #
Bypass Specic Gate Alarm USER PIN * 5 4 Zone Number #
Re-enable Gate Alarm (All Zones) USER PIN * 5 3 #
Re-enable Specic Gate Alarm USER PIN * 5 3 Zone Number #
Arm in Agricultural Mode (No Alarms) USER PIN * 9 Zone Number
Reset and Display Firmware Version USER PIN * 6 8 #
Reset and Return to Factory Defaults INSTALLER PIN * 6 8 #
Autres manuels pour Z28
2
Table des matières
Autres manuels JVA Alimentation
JVA
JVA Z Series Manuel utilisateur
JVA
JVA PET Series Manuel utilisateur
JVA
JVA Wi-Fi Anywhere PTE2704 Manuel utilisateur
JVA
JVA M1.5 Manuel utilisateur
JVA
JVA MB1.5 Manuel utilisateur
JVA
JVA IP Energizer MB 16 Manuel utilisateur
JVA
JVA Z Series Manuel utilisateur
JVA
JVA M1.5 Manuel utilisateur
JVA
JVA Z13 Manuel utilisateur
JVA
JVA MB8 Manuel utilisateur
JVA
JVA Wi-Fi Anywhere PTE2700 Manuel utilisateur
JVA
JVA RSG1 Manuel utilisateur
JVA
JVA Z114 Manuel utilisateur
JVA
JVA SV2 Manuel
JVA
JVA MB8 Manuel utilisateur
JVA
JVA Z28 Manuel utilisateur
JVA
JVA Z Series Guide de l'utilisateur
JVA
JVA Z14 Manuel utilisateur
JVA
JVA Z28 Manuel utilisateur
JVA
JVA Wi-Fi Anywhere WA20M Manuel utilisateur
