Jura IMPRESSA J5 Manuel utilisateur

IMPRESSA J5 – Quick Reference Guide

The ‘IMPRESSA Manual’ together with these short instruc-

tions ‘IMPRESSA J5 – Quick Reference Guide’ has been

awarded the seal of approval by the independent German

Technical Inspection Agency, TÜV SÜD, due to its easy-to-

understand style, its thoroughness and coverage of safety

aspects.

IMPRESSAJ5 – Quick Reference Guide

These short instructions do not replace the ‘IMPRESSA J5 Manual’.

Makesureyoureadandobservethesafetyinformationandwarnings

first in order to avoid hazards.

When the IMPRESSA is switched on, a prompt to perform a rinse

operation automatically appears.

Precondition: Your IMPRESSA is switched on at the power switch

and the On/Off button gis illuminated (standby).

glPress the On/Off button to switch the IMPRESSA on.

HEATING

PRESS RINSE, the maintenance button hlights up.

lPlace a receptacle under the coffee spout.

h l Press the maintenance button.

The machine will rinse itself, stopping automatically.

READY appears on the display. Your IMPRESSA is ready to

use.

AclassicItalianrecipe.TheCappuccinoismadeupofone-thirdeach

of Espresso, hot milk and milk foam. The finishing touch is a sprin-

kling of cocoa powder.

Precondition: The Professional Cappuccino Frother is installed.

lTake the milk pipe out of the Welcome Pack.

lTake the protective cap off the Professional Cappuccino

Frother.

lAttach the milk pipe to the nozzle.

lInsert the other end in a milk carton/bottle or connect it to

a milk container.

lPlace a cup under the Professional Cappuccino Frother.

Switching on

Cappuccino

IMPRESSAJ5 – Quick Reference Guide

lTurn the selection lever of the nozzle to the milk foam

position .

k l Press the steam button.

HEATING

READY appears as soon as the IMPRESSA has heated up.

k l Press the steam button.

STEAM, the milk foam is being prepared.

Theoperationstopsautomaticallyafterreachingthepre-set

amount of steam.

oThe milk foam preparation can be interrupted at any time. To

do this, press any button.

oWhile milk foam is being prepared, you can change the pre-

set amount of water by turning the rotary switch.

oYou can continue with preparing milk foam within approx.

40 seconds.

lMove the cup under the coffee spout.

a l Press the 1 Espresso button.

1ESPRESSO appears on the display. After this, the

strength is briefly displayed.

The pre-set amount of water flows into the cup.

Drink preparation stops automatically. READY appears on

the display.

To ensure that the Professional Cappuccino Frother works perfectly,

you should rinse and clean it regularly. You can find more informa-

tion under ‘Maintenance – Professional Cappuccino Frother’.

IMPRESSAJ5 – Quick Reference Guide

YourIMPRESSAnolongerhastobedescaledifyouareusingCLARIS

filter cartridges.

oPerformthe‘Insertfilter’operationwithoutinterruptions.This

will ensure that your IMPRESSA always produces its best.

oAfter two months, the filter will cease to work. Monitor the

elapsed time as shown on the date plate on the cartridge

holder.

Precondition: READY appears on the display.

m l Keep the rotary switch pressed until RINSE appears on

the display.

ä l Turn the rotary switch until FILTER - appears.

m l Press the rotary switch to enter the programme item.

NO - appears on the display.

ä l Turn the rotary switch until YES √ appears.

m l Press the rotary switch to confirm this setting.

OK appears briefly on the display to confirm the setting.

INSERT, the maintenance button hlights up.

lRemove the CLARIS filter cartridge and the filter cartridge

extension from the Welcome Pack.

lStick the extension on top of the filter cartridge.

lRemove the water tank and empty it.

lLift the cartridge holder and insert the filter cartridge into

the water tank, applying light pressure.

lClose the cartridge holder. It will click into place audibly.

lFill the water tank with cold, fresh mains water and

reinsert.

lPlace a receptacle (at least 500 ml) under the Professional

Cappuccino Frother.

Using and activating

filter

IMPRESSAJ5 – Quick Reference Guide

lTurn the selection lever of the nozzle to the steam

position k.

h l Press the maintenance button.

FILTER RINSING. Waterwillflow outatthenozzle.

oYou can interrupt the rinsing of the filter at any time by

pressing any button.

oThe water may be slightly discoloured. This is not harmful to

health, nor does it affect the taste.

Filter rinsing stops automatically after approx. 500 ml.

HEATING appears on the display, and then READY

appears. The filter is now activated.

oAfter 50 litres of water have flowed through, the filter will

cease to work. Your IMPRESSA will automatically prompt you

to change the filter.

oAfter two months, the filter will cease to work. Monitor the

elapsed time as shown on the date plate on the cartridge

holder.

oIf the CLARIS filter cartridge is not activated, you will not be

prompted to change the filter.

Precondition:FILTER /READY appearson the display, and the

maintenance button lights up.

h l Press the maintenance button.

CHANGE

lRemove the water tank and empty it.

lOpenupthecartridgeholderandremovetheoldCLARISfil-

ter cartridge and the extension piece.

lStick the extension on top of a new CLARIS filter cartridge.

lInsert the filter cartridge into the water tank with light pres-

sure.

Changing the filter

IMPRESSAJ5 – Quick Reference Guide lClose the cartridge holder. It will click into place audibly.

lFill the water tank with cold, fresh mains water and reinsert.

lPlace a receptacle (at least 500 ml) under the Professional

Cappuccino Frother.

lTurn the selection lever of the nozzle to the steam

position k.

h l Press the maintenance button.

FILTER RINSING. Waterwillflow outatthenozzle.

oYoucaninterruptthefilterrinsingatanytime.Todothis,press

any button.

oThe water may be slightly discoloured. This is not harmful to

health, nor does it affect the taste.

Filter rinsing stops automatically after approx. 500 ml.

HEATING appears on the display, and then READY

appears.

After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA

will prompt you to clean it.

Ifthewrongcleaningagentisused,themachinecouldbe damaged

and/or traces of detergent could be left behind in the water.

lUse only original JURA care products.

oThe cleaning programme only lasts about 15 minutes.

oDo not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

oJURA cleaning tablets are available from your stockist.

Precondition: CLEAN /READY appears on the display, and the

maintenance button hlights up.

Clean machine

CAUTION

IMPRESSAJ5 – Quick Reference Guide

h l Press the maintenance button.

EMPTY TRAY

lEmpty the drip tray and coffee grounds container and put

them back into the machine.

PRESS RINSE – The maintenance button hlights up.

lPlace a receptacle (at least 500 ml) under the coffee spout.

h l Press the maintenance button.

CLEANING – Water flows out of the coffee spout.

The process is interrupted – ADD TABLET.

lOpen the cover of the filler funnel for pre-ground coffee.

lInsert a JURA cleaning tablet into the filler funnel.

lClose the cover of the filler funnel.

PRESS RINSE – The maintenance button hlights up.

h l Press the maintenance button.

CLEANING

Water flows out of the coffee spout several times.

The process is interrupted – EMPTY TRAY.

lEmpty the drip tray and coffee grounds container and put

them back into the machine.

The cleaning operation is now complete. The cleaning

operation is now complete.

The IMPRESSA builds up deposits of limescale over time and auto-

matically prompts you to descale it when necessary. The degree of

calcification depends on the degree of hardness of your water.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

lAvoid contact with the skin or eyes.

lRinsethedescalingagentoffwithcleanwater.Shouldyouget

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dam-

aged and/or traces of detergent could be left behind in the water.

lUse only original JURA care products.

Descale machine

CAUTION

IMPRESSAJ5 – Quick Reference Guide

If the descaling operation is interrupted, there may be damage to

the machine.

lAllow the descaling program to run to the end.

If the descaling agent comes into contact with sensitive surfaces,

damage cannot be ruled out.

lClean up any splashes immediately.

oThe descaling programme lasts approx. 40 minutes.

oJURA descaling tablets are available from your stockist.

oIf you use a CLARIS filter cartridge and this is activated, you

will not be prompted to change the filter.

Precondition: DE-SCALE /READY appears on the display, and

the maintenance button hlights up.

h l Press the maintenance button.

EMPTY TRAY

lEmpty the drip tray and coffee grounds container and put

them back into the machine.

AGENT IN TANK

lRemove the water tank and empty it.

lCompletely dissolve the contents of one blister (3 JURA

descaling tablets) in a container that holds 500 ml of water.

This may take several minutes.

lPour the solution into the empty water tank and insert it in

the machine.

AGENT IN TANK – The maintenance button hlights

up.

lRemove the nozzle.

lPlace a receptacle (at least 500 ml) under the Connector

System©.

h l Press the maintenance button.

DE-SCALING

ThiscauseswatertoflowoutoftheConnectorSystem©.The

maintenance button blinks during the descaling operation.

The operation stops automatically – EMPTY TRAY.

lEmpty the drip tray and coffee grounds container and put

them back into the machine.

CAUTION

IMPRESSAJ5 – Quick Reference Guide

lEmpty the container under the Connector System©.

FILL WATER TANK

lRinse the water tank thoroughly and fill it with cold, fresh

mains water.

lPut the water tank back in.

PRESS RINSE – The maintenance button hlights up.

lPlace a container under the Connector System©.

h l Press the maintenance button.

This causes water to flow out of the Connector System©.

The operation stops automatically – EMPTY TRAY.

lEmpty the drip tray and coffee grounds container and put

them back into the machine.

lReplace the nozzle.

The descaling operation is now complete.

The IMPRESSA heats up and is ready for use again.

oIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

To ensure that the Professional Cappuccino Frother works perfectly,

you should rinse it with water after every milk preparation.

oThe IMPRESSA will not prompt you to rinse the Professional

Cappuccino Frother.

lRemove the milk pipe from the milk carton/bottle or the

milk container.

lFill the receptacle with 250 ml of fresh water and immerse

the milk pipe in it.

lPlace a receptacle under the Professional Cappuccino

Frother.

lTurn the selection lever to the milk or milk foam

position.

k l Press the steam button.

HEATING

READY

Rinse Professional

Cappuccino Frother

IMPRESSAJ5 – Quick Reference Guide

k l Press the steam button again.

STEAM – The nozzle and pipe are rinsed.

lPress any button as soon as clean water flows into the cup.

To ensure that the Professional Cappuccino Frother works perfectly,

you should clean it daily when you have been preparing milk.

Ifthewrongcleaningagentisused,themachinecouldbe damaged

and/or traces of detergent could be left behind in the water.

lUse only original JURA care products.

oThe IMPRESSA will not prompt you to clean the Professional

Cappuccino Frother.

oThe JURA Cappuccino Cleaner is available from your stockist.

lPlace a receptacle under the Professional Cappuccino

Frother.

lPour 250 ml of fresh water into a container and add one

capful (max. 15 ml) of Cappuccino Cleaner.

lImmerse the milk pipe in the receptacle.

lTurn the selection lever to the milk or milk foam

position.

k l Press the steam button.

HEATING

READY

k l Press the steam button again.

STEAM

Ä l Turn the rotary switch until 60 SEC appears on the

display.

STEAM – The nozzle and pipe are cleaned.

lPressanybuttonas soon asthereceptaclewith the Cappuc-

cino Cleaner is empty.

Clean Professional

Cappuccino Frother

CAUTION

Autres manuels pour IMPRESSA J5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Jura Cafetière

Jura

Jura IMPRESSA C5 Manuel utilisateur

Jura

Jura 747 Manuel utilisateur

Jura

Jura E6 Manuel utilisateur

Jura

Jura 744 Manuel utilisateur

Jura

Jura ENA Micro 90 Manuel utilisateur

Jura

Jura IMPRESSA C9 Manuel utilisateur

Jura

Jura GIGA X9c Professional Guide de configuration

Jura

Jura 746 Manuel utilisateur

Jura

Jura Professional fine foam frother Manuel utilisateur

Jura

Jura IMPRESSA X30 Manuel utilisateur

Jura

Jura IMPRESSA XJ5 Professional Manuel utilisateur

Jura

Jura 729 Manuel utilisateur

Jura

Jura GIGA6 Manuel utilisateur

Jura

Jura IMPRESSA XJ9 OT TFT Professional Manuel

Jura

Jura 579 Manuel utilisateur

Jura

Jura GIGA X8c Guide de configuration

Jura

Jura ENA 8 Manuel utilisateur

Jura

Jura S8 Manuel utilisateur

Jura

Jura E4 Manuel utilisateur

Jura

Jura IMPRESSA J9.3 One Touch TFT Manuel utilisateur

Jura

Jura Impressa F9 guide Manuel utilisateur

Jura

Jura IMPRESSA XF50 Classic Manuel utilisateur

Jura

Jura Impressa E Manuel utilisateur

Jura

Jura WE6 Professional Manuel

Manuels Cafetière populaires d'autres marques

Taurus

Taurus Livorno 6 Manuel utilisateur

Delta-q

Delta-q QUICK Manuel utilisateur

Bunn

Bunn LCA-1 Guide de dépannage

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instructions d'installation

Saeco

Saeco Vienna Plus Sup 018M Manuel utilisateur

DeLonghi

DeLonghi DC300 Manuel utilisateur

INCAPTO

INCAPTO BXCO1470E Manuel utilisateur

Bosch

Bosch TASSIMO finesse TAS16B Series Manuel utilisateur

Exido

Exido 245-072 Manuel utilisateur

Animo

Animo OptiVend Choco Manuel utilisateur

Siemens

Siemens TQ505DF Series Manuel utilisateur

DeLonghi

DeLonghi ECI341 Manuel utilisateur

Krups

Krups KT406511 Manuel utilisateur

Cimbali

Cimbali M32 Classic Manuel utilisateur

Philips

Philips HL3844N Manuel utilisateur

Bosch

Bosch TES 515 SERIES Manuel utilisateur

Tekmatix

Tekmatix TMFM - 65 Manuel utilisateur

Scarlett

Scarlett SC-CM33005 Manuel utilisateur