Jura E6 Manuel utilisateur

E6/E60 – Quick Reference Guide

These short instructions do not replace the ‘E6/E60 Instructions for

Use’. Make sure you read and observe the safety information and

warnings first in order to avoid hazards.

You can start coffee system rinsing manually at any time.

Precondition: The start screen is displayed.

TPlace a receptacle under the coffee spout.

TPress the ‘ c’ button (white Maintenance symbol).

TPress the ‘Rinse the coffee system’ button to start the rinse

operation.

‘Machine is rinsing’, water flows out of the coffee spout. The

operation stops automatically. The start screen is displayed.

After each milk preparation, the JURA prompts you to perform a milk

system rinse.

Precondition: ‘Rinse the milk system’ is displayed.

TPlace a receptacle under the fine foam frother.

TPress the ‘ c’ button (red Maintenance symbol).

‘Switch open’

TTurn the switch to the xposition.

‘Milk system is being rinsed’appears and the fine foam fro-

ther is rinsed.

The rinse stops automatically. ‘Switch close’ appears on the

display.

TTurn the switch to the °position.

The start screen is displayed.

Rinsing the machine

E6/E60 – Quick Reference Guide

To ensure that the fine foam frother always works properly, you

must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged

and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

EJURA milk system cleaner is available from specialised dealers.

Precondition: The start screen is displayed.

TPress the ‘P’button.

TPress the ‘Clean the milk system’ button.

‘Clean the milk system’

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Clean the milk system’ / ‘Milk system cleaner’

TRemove the milk pipe from the milk container or carton.

TPour 250 ml of fresh water into a receptacle and add 1 capful

of milk system cleaner.

TImmerse the milk pipe in the receptacle.

TPlace a receptacle under the fine foam frother.

TPress the ‘Next’ button.

As soon as the machine has heated up, ‘Switch open’

appears.

TTurn the switch to the xposition.

‘Milk system is being cleaned’ appears and the fine foam fro-

ther and the milk pipe are cleaned.

‘Switch close’

TTurn the switch to the °position.

‘Clean the milk system’

TRinse the receptacle thoroughly, fill it with 250 ml of fresh

water and immerse the milk pipe in the water.

TEmpty the other receptacle and place it under the fine foam

frother once more.

TPress the ‘Next’ button.

‘Switch open’

TTurn the switch to the xposition.

Cleaning the fine foam

frother

CAUTION

E6/E60 – Quick Reference Guide

‘Milk system is being cleaned’ appears and the fine foam fro-

ther and the milk pipe are rinsed with fresh water.

‘Switch close’

TTurn the switch to the °position.

The start screen is displayed.

To make sure the fine foam frother works properly, and in the inte-

rests of hygiene, it must be dismantled and rinsed daily if you have

been preparing milk. Your JURA will not prompt you to dismantle

and rinse the frother.

TRemove the milk pipe and rinse it thoroughly under running

water.

TCarefully remove the fine foam frother from the Connector

System©by twisting slightly.

TDismantle the fine foam frother into its individual parts.

TRinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts

in a solution of 250 ml cold water and 1 capful of JURA milk

system cleaner. Then rinse the parts thoroughly.

TRe-assemble the fine foam frother.

EEnsure that all individual parts are correctly and firmly

connected to ensure optimum operation.

TFirmly attach the fine foam frother to the Connector

System©.

Your JURA no longer has to be descaled if you are using the CLARIS

Smart filter cartridge. If you did not insert the filter cartridge the first

time you used the machine, you can do this now as follows.

Precondition: The start screen is displayed.

TRemove and empty the water tank.

TFit the filter cartridge extension supplied on top of a CLARIS

Smart filter cartridge.

Dismantling and rinsing

the fine foam frother

Inserting the filter

E6/E60 – Quick Reference Guide

TInsert the filter cartridge with its extension into the water

tank.

TTurn the filter cartridge clockwise until it audibly clicks into

place.

TFill the water tank with fresh, cold water and reinsert the

tank.

EThe machine automatically detects that you have just inserted

the filter cartridge.

‘Saved’ appears briefly on the display.

‘Switch open’

TPlace a receptacle (at least 300 ml) under the fine foam fro-

ther.

TTurn the switch to the xposition.

‘Filter is being rinsed’, water flows out of the fine foam fro-

ther.

Rinsing of the filter stops automatically after approximately

300 ml. ‘Switch close’ appears on the display.

TTurn the switch to the °position.

The start screen is displayed.

EIf the filter is active, this is indicated by a blue filter symbol at

the bottom of the display.

EOnce the filter cartridge stops working (depending on the

water hardness setting), the JURA will prompt you to change

the filter.

ECLARIS Smart filter cartridges are available from specialised

dealers.

Precondition: The start screen is displayed. The filter symbol at the

bottom of the display lights up red.

TRemove and empty the water tank.

TTurn the filter cartridge anticlockwise and remove it along

with the extension from the water tank.

Changing the filter

E6/E60 – Quick Reference Guide

TFit the filter cartridge extension on top of a new CLARIS

Smart filter cartridge.

TInsert the filter cartridge with its extension into the water

tank.

TTurn the filter cartridge clockwise until it audibly clicks into

place.

TFill the water tank with fresh, cold water and reinsert the

tank.

‘Saved’ appears briefly on the display. The machine has

automatically detected that you have just changed the filter

cartridge.

‘Switch open’

TPlace a receptacle (at least 300 ml) under the fine foam fro-

ther.

TTurn the switch to the xposition.

‘Filter is being rinsed’, water flows out of the fine foam fro-

ther.

EYou can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to

continue rinsing the filter.

EThe water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately

300 ml. ‘Switch close’ appears on the display.

TTurn the switch to the °position.

The start screen is displayed.

The JURA builds up deposits of limescale over time and automati-

cally prompts you to descale it when necessary. The degree of calci-

fication depends on the hardness of your water.

EIf you are using a CLARIS Smart filter cartridge, you will not be

prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this

can cause irritation.

TAvoid contact with the skin or eyes.

Descaling the machine

JCAUTION

E6/E60 – Quick Reference Guide

TRinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be dama-

ged and/or traces could be left behind in the water.

TUse only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to

the machine.

TAllow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces

(e.g. marble), damage cannot be ruled out.

TClean up any splashes immediately.

EThe descaling programme lasts approximately 40 minutes.

EJURA descaling tablets are available from specialised dealers.

Precondition: ‘Decalcify machine’ is displayed.

TPress the ‘ c’ button (red Maintenance symbol).

‘Descale’

TPress the ‘Start’ button.

TPress the ‘Next’ button.

‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Agent in tank’

TRemove and empty the water tank.

TCompletely dissolve the contents of one blister (3 JURA des-

caling tablets) in a receptacle holding 500 ml of lukewarm

water. This may take several minutes.

TPour the solution into the empty water tank and insert it into

the machine.

‘Switch open’

CAUTION

E6/E60 – Quick Reference Guide

TPlace a receptacle under the fine foam frother.

TTurn the switch to the xposition.

‘Machine is being descaled’ appears and water flows out of

the fine foam frother repeatedly.

The operation is interrupted, ‘Switch close’.

TTurn the switch to the °position.

‘Machine is being descaled’, the descaling operation is

continued.

The operation is interrupted, ‘Empty drip tray’.

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

‘Fill water tank’

TEmpty the receptacle and place it under the fine foam fro-

ther and the coffee spout.

TRemove the water tank and rinse it thoroughly.

TFill the water tank with fresh, cold water and reinsert the

tank.

‘Switch open’

TTurn the switch to the xposition.

‘Machine is being descaled’, the descaling operation is con-

tinued.

The operation is interrupted, ‘Switch close’.

TTurn the switch to the °position.

‘Machine is being descaled’, the descaling operation is con-

tinued. Water flows out of the coffee spout.

The operation is interrupted ‘Empty drip tray’

TEmpty the drip tray and coffee grounds container and put

them back into the machine.

Descaling is now complete. The start screen is displayed.

EIf the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

Autres manuels pour E6

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Jura Cafetière

Jura

Jura IMPRESSA Z7 Manuel utilisateur

Jura

Jura IMPRESSA S9 One Touch Manuel utilisateur

Jura

Jura 748 Manuel utilisateur

Jura

Jura IMPRESSA XF50 Classic Manuel utilisateur

Jura

Jura IMPRESSA X9 Manuel utilisateur

Jura

Jura IMPRESSA XJ9 Professional Manuel utilisateur

Jura

Jura X7 Manuel utilisateur

Jura

Jura IMPRESSA J9.3 One Touch TFT Manuel utilisateur

Jura

Jura GIGA X7 Professionel Manuel utilisateur

Jura

Jura IMPRESSA C9 Instructions de montage

Jura

Jura J8 Manuel utilisateur

Jura

Jura 759 Manuel utilisateur

Jura

Jura Giga X3 Professional Guide de configuration

Jura

Jura IMPRESSA A9 One Touch Manuel utilisateur

Jura

Jura IMPRESSA Z7 Manuel utilisateur

Jura

Jura Impressa J6 Manuel utilisateur

Jura

Jura GIGA 5 Manuel utilisateur

Jura

Jura Z8 Manuel utilisateur

Jura

Jura IMPRESSA Z5 Manuel utilisateur

Jura

Jura 734 Manuel utilisateur

Jura

Jura IMPRESSA J9 One Touch Manuel utilisateur

Jura

Jura IMPRESSA X9 Manuel utilisateur

Jura

Jura IMPRESSA J9.2 One Touch Manuel utilisateur

Jura

Jura IMPRESSA X9 Manuel utilisateur

Manuels Cafetière populaires d'autres marques

Taurus

Taurus Livorno 6 Manuel utilisateur

Delta-q

Delta-q QUICK Manuel utilisateur

Bunn

Bunn LCA-1 Guide de dépannage

Black & Decker

Black & Decker BLACK DECKER HOME DE790 Instructions d'installation

Saeco

Saeco Vienna Plus Sup 018M Manuel utilisateur

DeLonghi

DeLonghi DC300 Manuel utilisateur

INCAPTO

INCAPTO BXCO1470E Manuel utilisateur

Bosch

Bosch TASSIMO finesse TAS16B Series Manuel utilisateur

Exido

Exido 245-072 Manuel utilisateur

Animo

Animo OptiVend Choco Manuel utilisateur

Siemens

Siemens TQ505DF Series Manuel utilisateur

DeLonghi

DeLonghi ECI341 Manuel utilisateur

Krups

Krups KT406511 Manuel utilisateur

Cimbali

Cimbali M32 Classic Manuel utilisateur

Philips

Philips HL3844N Manuel utilisateur

Bosch

Bosch TES 515 SERIES Manuel utilisateur

Tekmatix

Tekmatix TMFM - 65 Manuel utilisateur

Scarlett

Scarlett SC-CM33005 Manuel utilisateur