Jura IMPRESSA X9 Manuel utilisateur
Dimo Espresso Services
Jura Impressa X9 Descaling Process
Your IMPRESSA X9 Coffee maker machine builds up deposits of limescale over time and
automatically prompts you to descale it when necessary. The degree of calcification depends on
the degree of hardness of water at location machine is in use.
CAUTION
If the wrong descaling agent is used, the machine could be damaged and/or traces of
detergent could be left behind in the water. Use only original JURA care products.
Once started, the descaling operation must not be interrupted. If the descaling
operation is interrupted, there may be damage to the machine.
Allow the descaling program to run to the end. The descaling program lasts approx.
45 minutes.
If you use a CLARIS filter cartridge and this is activated meaning that the machine is
programmed in filter mode, or the water hardness is set to ‘not active’, you will not be
prompted to descale the machine. In this case descaling operation can only be started by
Jura or any specialized service technician.
If you are using a CLARIS filter cartridge, you must always remove it before
descaling. Do not descale the machine if a CLARIS filter cartridge is fitted.
Your IMPRESSA machine is ready for descale operation, when the message
is shown on the display.
Note:
We recommend that to descale machine within the same day that message appears on display. If
you make more coffees, the display will indicate: DECALCIFY. After yet even more coffees made,
the display will read: DECALCIFY NOW.
Open the cover of the programming buttons on front. As it
is shown in the picture and then press.....
COFFEE READY
DESCALE
Dimo Espresso Services
As it is showing on fig on side. At this
moment on machine's display will appear
DESCALING
START
YES
Also See the two figures below
To initiate descaling process press descale button again. At this moment on
machine's display you will see messages such as: EMPTY TRAY and EMPTY
COFFEE
Shown also in the two pictures below BIN
Remove the drip tray and the coffee grounds bin from machine and EMPTY both of them
before starting descaling process. As the drip tray and coffee grounds bin have been removed
from machine to be emptied you will see on machine's display messages such as:
COFFEE BIN and TRAY MISSING
MISSING
Place both ground coffee bin and drip tray into machine, as soon as both these items are placed
back into machine, you will see that machine instantly and automatically will switch to the next step
and on machine's display will appear: SOLVENT IN TANK Which is shown also in the picture at
next page. PRESS
KEY
Press the
descaling button.
Dimo Espresso Services
Completely dissolve three JURA descaling tablets in a container that holds 700 ml of water.
This may take several minutes. Pour the prepared solution into the empty water tank and insert it in
the machine.
Place three large receptacles under the dual spout,
the steam pipe and the hot water pipe. As it is shown in
figure on side and then.....
Press descale button again, machine automatically will start descaling process, water
flows from steam pipe; the dual spout and hot water pipe and at this time on machine's display you
will see the MACHINE DECALCIFYING message. Also you can follow the current status of
descaling process on the progress bar as it is shown in picture below
Dimo Espresso Services
When the descaling solution is emptied in water tank the descaling process automatically is
interrupted, at same time you will hear an acoustic signal beeping and EMPTY TRAY message will
appear on machine's display. Remove the drip tray from machine, empty it and place it back into
machine.
As soon as drip tray is placed back into machine WATER TANK message taken place
(Shows up) on machine's display. RINSE/FILL
Thoroughly rinse out water tank and fill it with fresh cold tap water, place water tank back into
machine. With this taken action we're starting the second part of descaling process RINSING.
Before starting rinsing process, make sure to not to forget to empty the three large
receptacles and place them back as it is shown previously in first part of descaling process and
then press.....
Descaling button again. The following steps will be the same as explained above in
first part of descaling process. When water is emptied in water tank the rinsing process
automatically is interrupted, at same time you will hear an acoustic signal beeping
an EMPTY TRAY and EMPTY
COFFEE
BIN messages will appear on machine's display. Remove both the drip tray
and the coffee grounds bin from machine, empty them and place them back into machine. After
this taken action your IMPRESSA is once more ready for operation and the final message
appeared on machine's display will be: COFFE READY
Autres manuels pour IMPRESSA X9
5
Table des matières
Autres manuels Jura Cafetière
Jura
Jura Z6 Manuel utilisateur
Jura
Jura X90/X95 Manuel utilisateur
Jura
Jura IMPRESSA XJ5 Professional Manuel utilisateur
Jura
Jura GIGA X8c Guide de configuration
Jura
Jura GIGA X8c Mode d’emploi
Jura
Jura A9 Manuel utilisateur
Jura
Jura SUBITO Manuel utilisateur
Jura
Jura IMPRESSA E85 Manuel utilisateur
Jura
Jura E8 Manuel utilisateur
Jura
Jura IMPRESSA F50 Classic Manuel utilisateur
Jura
Jura ENA Micro 1 Manuel utilisateur
Jura
Jura GIGA X8 Professional Manuel utilisateur
Jura
Jura IMPRESSA Z7 Manuel utilisateur
Jura
Jura E8 Manuel utilisateur
Jura
Jura IMPRESSA E30 Manuel utilisateur
Jura
Jura GIGA X9c Professional Manuel utilisateur
Jura
Jura ENA Micro 90 Manuel utilisateur
Jura
Jura Giga X3 Professional Manuel utilisateur
Jura
Jura IMPRESSA Z7 Manuel utilisateur
Jura
Jura The IMPRESSA Z5 - Generation II Manuel utilisateur
