JupiterTech DEFIANT Manuel utilisateur
USER MANUAL
PACKAGE CONTENTS
To ensure the safety and enjoyment of
your electric bike, please read the user
manual carefully and check whether
all the parts are in good condition
before riding. Please abide by all safety
measures and contact us if there are
any problems.
E-Bike x 1
Saddle & Seat Tube x 1
User Manual x 1
Charger x 1
Battery Lock Keys x2
JupiterTech
5600 Airport Blvd., Suite C
Tampa, FL 33634
813-609-BIKE (2453)
www.jupiterbike.com
NOTE
Manual illustrations are for demonstration
purposes only. Illustrations may not reect exact
appearance of actual product. “Specications
subject to change without notice.”
TABLE OF CONTENTS
Structural Diagram - 4
Initial Setup - 5
Unfolding the Handle Stem - 6
Installing the Handle - 7
Installing the Seat Post - 8
Unfolding the Pedals - 9
Charging the Battery - 10
Removing the Battery - 11
Battery and Charger Care - 12
The LCD Display - 13
Turning on Your Bike - 15
Precautions When Riding - 16
Maintenance & Storage - 17
Troubleshooting - 18
Warnings - 19
Acceptable Riding Practices and
Conditions - 22
Warranty - 23
Returns - 23
4
STRUCTURAL DIAGRAM
Handle Brake
Stem
Latch Lock
Stem Latch
Flashlight
Front Fork
Disc Break
Chainwheel
Bike Frame Latch
Saddle
Seat Post
Seat Post Clamp
Motor Pedal
Bike Frame
5
1. Turn the bike upside down as it is easier to install wheel 2. Adjust the front fork and ensure it
is facing the correct way
4. Secure wheel with the quick
release
3. Place the front wheel on the front fork, ensuring the
brake plate is align with the brake
INITIAL SETUP
6
1. Tilt stem upright to ensure it connects
seamlessly with the base
3. Push lever upward to ush silver knob,
which secures handle stem to the base
2. To ensure seamless t, press the lever
down, so that the silver knob is out.
4. Fasten lever to rmly lock the handle in
place.
UNFOLDING THE HANDLE STEM
7
1. Lift the quick-release lock from the
handlebar holder and remove the lower screw
3. Place the handlebar inside the holder, then
close the holder allowing the screw to come
through the bottom hole.
2. Set aside the nut and gasket, but leave the
screw in place.
4. Adjust handle bar angle and position to your
preference. Then reinstall the nut and gasket
to tighten
INSTALLING THE HANDLE
8
4. To secure the saddle, tighten the seat post clamp as
pictured, and then press the seat downward rmly to
ensure it stays in place.
1. Loosen the seat post clamp and insert saddle post.
2. Adjust saddle to the preferred
height then tighten clamp.
INSTALLING THE SEAT POST
9
UNFOLDING THE PEDALS
1. To unfold pedals, push up pedal
3. To fold pedals, press it inward
2. Pull pedal towards you. The pedal is secure
when you hear a click.
4. Fold pedal into a upward position
10
CHARGING THE BATTERY
Be sure to charge the battery before your rst
ride!
Option 2: Remove battery from bike frame
(See next page)
Option 1: Insert charger to charge from the
bike frame port
Option 2: Plug in charger directly into the
battery
Table des matières
Manuels Scooter populaires d'autres marques
First Choice Mobility
First Choice Mobility Roma Medical Corella S741 Manuel utilisateur
Carrera
Carrera impel Manuel utilisateur
Afikim
Afikim Superlight SL-3 Manuel utilisateur
CareCo
CareCo ZOOM Manuel utilisateur
Douglas
Douglas Vespa G.S. Manuel utilisateur
Gazelle
Gazelle with BOSCH System Manuel utilisateur