Juniper EX8200 Series Manuel utilisateur

Connecting Power to an EX 8200 series Switch

An EX 8208 switch can be configured with up to six AC power supplies. After you

have installed at least one power supply, you can connect power to the switch.

CAUTION: To meet safety and electromagnetic interference (EMI) requirements and

to ensure proper operation, EX 8200 series switches must be adequately grounded

before they are connected to power.

For installations that require a separate grounding conductor to the chassis, use the

protective earthing terminal on the EX 8200 series switch chassis to connect to the

earth ground. For instructions on connecting an EX 8200 series switch to ground

using a separate grounding conductor, see Connecting Earth Ground to an EX-series

Switch.

An EX 8200 series switch gets additional grounding when you plug the power supply

in the switch into a grounded AC power outlet by using the AC power cord appropriate

for your geographical location. See AC Power Cord Specifications for an EX 8200

series Switch.

NOTE: Each power supply must be connected to a dedicated AC power source outlet.

Before you begin to connect power to the switch:

■Ensure you understand how to prevent ESD damage. See Prevention of

Electrostatic Discharge Damage on EX-series Switches.

■Install power supplies in the switch. See Installing an AC Power Supply in an EX

8200 series Switch.

Ensure that you have the following parts and tools available to connect power to the

switch:

■Electrostatic discharge (ESD) grounding strap

■Power cords appropriate for your geographical location. See AC Power Cord

Specifications for an EX 8200 series Switch.

WARNING: Ensure that the power cords do not block access to switch components

or drape where people can trip on them.

To connect AC power to an EX 8200 series switch:

1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to the ESD point on the chassis.

2. Ensure that the power supply is fully inserted and latched securely in the chassis.

See Installing an AC Power Supply in an EX 8200 series Switch.

Connecting Power to an EX 8200 series Switch ■1

3. Flip the Enable switch, which is next to the appliance inlet on the power supply

faceplate, to the Standby position.

4. Squeeze the two sides of the power cord retainer clip, and insert the L-shaped

ends of the clip into the holes in the bracket on each side of the AC appliance

inlet on the AC power supply faceplate. See Figure 1 on page 2.

Figure 1: Power Cord Retainer in an AC Power Supply

5. Locate the power cord or cords shipped with the switch; the cords have plugs

appropriate for your geographical location.

6. Insert the coupler end of the power cord into the AC appliance inlet on the AC

power supply faceplate.

NOTE: If the power cord tray is installed, you can thread the power cord through the

power cord tray. See Figure 2 on page 3.

7. Push the cord (close to the coupler end ) into the slot in the adjustment nut of

the power cord retainer. Rotate the nut until it is tight against the base of the

coupler and the slot in the nut is turned 90° from the top of the switch. See

Figure 2 on page 3.

8. If the AC power source outlet has a power switch, set it to the OFF (0) position.

9. Insert the power cord plug into an AC power source outlet.

10. If the AC power source outlet has a power switch, set it to the ON (|) position.

11. Verify that the INPUT OK LED on the power supply faceplate is lit and is on

steadily.

12. Flip the Enable switch on the power supply faceplate to the ON position.

13. Repeat steps 2 through 12 for the remaining power supplies.

2■Connecting Power to an EX 8200 series Switch

Figure 2: Connecting the Power Supply Cord to an EX 8200 series Switch

Related Topics ■AC Power Supply in an EX 8200 series Switch

■Power Supply LEDs in an EX 8200 series Switch

Connecting Power to an EX 8200 series Switch ■3

4■Connecting Power to an EX 8200 series Switch

Autres manuels pour EX8200 Series

13

Table des matières

Autres manuels Juniper Changer

Juniper

Juniper EX2200 Series Manuel utilisateur

Juniper

Juniper EX3200 Series Mode d’emploi

Juniper

Juniper QFX5120 Series Manuel utilisateur

Juniper

Juniper EX3300 Manuel utilisateur

Juniper

Juniper EX Series Manuel utilisateur

Juniper

Juniper EX2200 Series Instructions d'installation

Juniper

Juniper EX3400 Manuel utilisateur

Juniper

Juniper QFX5200 Instructions d'installation

Juniper

Juniper NETSCREEN-ISG 2000 Manuel utilisateur

Juniper

Juniper QFX3000-G QFabric Guide de référence rapide

Juniper

Juniper EX Series Mode d’emploi

Juniper

Juniper EX4500 Series Manuel utilisateur

Juniper

Juniper EX2300 Series Manuel utilisateur

Juniper

Juniper EX4100 Instructions d'installation

Juniper

Juniper QFX10002 Instructions d'installation

Juniper

Juniper EX9208 Instructions d'installation

Juniper

Juniper 200 Series Manuel utilisateur

Juniper

Juniper QFX5110-48S Manuel utilisateur

Juniper

Juniper EX2200 Series Instructions d'installation

Juniper

Juniper EX8208 Manuel utilisateur

Juniper

Juniper EX9214 Manuel utilisateur

Juniper

Juniper EX8200 Series Mode d’emploi

Juniper

Juniper QFX5220-32CD Manuel utilisateur

Juniper

Juniper EX4650 Series Instructions d'installation

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur