Juniper M7i Manuel utilisateur

Autres manuels pour M7i

4

Table des matières

Autres manuels Juniper Routeur réseau

Juniper

Juniper EX8200 Series Manuel utilisateur

Juniper

Juniper MX10003 Manuel utilisateur

Juniper

Juniper ACX5096 Manuel utilisateur

Juniper

Juniper E320 Manuel utilisateur

Juniper

Juniper NFX150-S1 Manuel utilisateur

Juniper

Juniper QFabric QFX5100-24Q Manuel utilisateur

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - E120 AND E320 HARDWARE GUIDE REV... Instructions d'installation

Juniper

Juniper MX2020 Instructions d'installation

Juniper

Juniper EX6210 Manuel utilisateur

Juniper

Juniper Internet Router M160 Instructions d'installation

Juniper

Juniper ACX1000 Instructions d'installation

Juniper

Juniper EX4300 Instructions d'installation

Juniper

Juniper PTX Series Manuel utilisateur

Juniper

Juniper J-Series Manuel utilisateur

Juniper

Juniper ACX4000 Instructions d'installation

Juniper

Juniper M10i Instructions d'installation et d'utilisation

Juniper

Juniper ERX-310 Manuel utilisateur

Juniper

Juniper MX2008 Instructions d'installation

Juniper

Juniper T640 Manuel utilisateur

Juniper

Juniper E SERIES BROADBAND SERVICES ROUTERS - E SERIES END-OF-LIFE MODULE GUIDE... Manuel utilisateur

Juniper

Juniper M40 Manuel utilisateur

Juniper

Juniper AP45 Manuel

Juniper

Juniper JUNOS J Series Manuel utilisateur

Juniper

Juniper M7i Instructions d'installation

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

Connecting Power to a DC-Powered M7i Router

Connect DC power to the router by inserting power cables into the field-wiring

terminals on the faceplate of each power supply. Power and grounding cables are

not supplied with the router. For information about the required cable type, see M7i

Chassis Grounding, Connection, and Cable Specifications.

NOTE: The router must be connected to at least two separate external DC power

sources.

CAUTION: There is no standard color coding for DC power cables. The color coding

used by the external DC power source at your site determines the color coding for

the leads on the power cables that attach to the terminal studs on each power supply.

You must ensure that power connections maintain the proper polarity. The power

source cables might be labeled (+) and (–)to indicate their polarity.

To connect DC power to the router (see Figure 1):

1. Verify that there is no power flowing from either external power source, so that

the voltage across the leads of the power cables is 0 V. Ensure that there is no

chance that the cable leads might become active during the procedure.

2. For each power supply, verify that the power switch on the power supply faceplate

is in the OFF (O) position.

3. Connect the grounding cable to a proper earth ground for each external DC

power sources, if it is not already.

4. Verify that a licensed electrician has attached the cable lug provided with the

router to the grounding cable.

5. Using a number 2 Phillips screwdriver, remove the screws next to the grounding

symbol above the power supplies on the chassis rear. Secure the grounding cable

lug to the chosen grounding point by reinstalling and tightening the screws.

6. Verify that a licensed electrician has attached a listed power cable lug to each

power source cable.

7. Loop the power cables through the hook located on the faceplate to the right of

the field-wiring terminals.

8. Depending on the type of power cable lugs used, loosen or remove the screws

on the field-wiring terminals.

9. Insert the power cable lugs into the appropriate field-wiring terminals. Using a

number 1 Phillips screwdriver, turn the screw on each field-wiring terminal

clockwise to secure the power cable lug. Apply between 8 lb-in. (.9 Nm) and 9

lb-in. (1.02 Nm) of torque to each screw.

a. Insert the positive (+) source cable into the return terminal, which is labeled

RTN.

Connecting Power to a DC-Powered M7i Router ■1

b. Insert the negative (–) source cable into the input terminal, which is labeled

–48V.

10. Verify that the DC source power cabling and the grounding cabling are correct,

that they are not touching or blocking access to router components, and that

they do not drape where people could trip on them.

Figure 1: Connecting DC Power and Grounding Cables

Related Topics M7i Router DC Power Supply Specifications■

■M7i DC Power Electrical Safety Guidelines

■DC Power Wiring Sequence Warning for M Series, MX Series, and T Series Routers

Published: 2009-08-03

2■Connecting Power to a DC-Powered M7i Router