Jung Observer 110 Manuel utilisateur
Observer 110
Observer 110
Art.-No.: 222 WW
Operationsmanual
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Danger of electric shock. Always disconnect before carrying out work on the devise or
load. At the same time, take into account all circuit breakers that supply dangerous
voltage to the device or load.
Do not press on the lens. Device can be damaged.
Do not open the sensor head, because close sealing is not possible. Foreign bodies and
spray water can penetrate and damage the device.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
picture 1: Device components
(1) Connection box
(2) Adjuster
(3) Sensor head
(4) Sensor window
(5) Manual knob
(6) Central screw
1/10
82508413
J:0082508413 18.08.2010
3 Function
Intended use
- Automatic switching of lighting depending on the heat motion and ambient brightness.
- Surface-mounting in indoor and outdoor areas
Product characteristics
- Variable installation position
- Protected against spray water
- Follow-up time, sensitivity and brightness value settable
- Test operation for checking the detection area
- Sensor head adjustable in 3 axes
- Screens for limiting the detection area
- 18 detection zones in 3 levels
- Parallel connection of multiple controllers possible
- Manual switch-on possible with installation button
Automatic operation
The controller detects heat motions of people, animals and objects.
- The light is switched on if a person enters the monitored detection area and the brightness
is below the set threshold.
- The light is switched off if no more movement is detected in the detection area and the
follow-up time has elapsed.
In order to avoid light oscillations due to the cooling of a bulb, the controller does not evaluate
any signals for approx. 2 seconds after switch-off.
4 Operation
Switching the light on manually
Optional push-button is installed.
o Press push-button briefly.
Light is switched on independently of the brightness for the set follow-up time.
When motions are detected, the follow-up time is restarted.
Configuring the controller
The controller has one adjuster each for the brightness threshold, the follow-up time and the
operating mode.
picture 2: Adjuster
2/10
82508413
J:0082508413 18.08.2010
Observer 110
(7) Adjuster for brightness threshold, LUX
(8) Adjuster for operating mode, TEST, ON
(9) Adjuster for follow-up time, TIME
Switch on test operation
In test operation the motion detector operates independently of the brightness. The follow-up
time is approx. 1 second. The motion detector switches on cyclically as long as there is
movement in the detection area.
o Turn adjuster for operating mode (8) to TEST position (picture 2).
i The adjusters TIME and LUX have no function in test operation.
Switching on automatic mode
o Turn adjuster for operating mode (8) to ON position (picture 2).
Setting the brightness threshold
Only when the brightness drops below the threshold will the light be switched on when there is
motion in the detection area. The brightness threshold is steplessly adjustable in a range from
approx. 5 to 300 lux.
o Turn adjuster LUX (7) to the appropriate position (picture 2).
Position Function
3 switches independently of the brightness
300 lux switches when there are heavy clouds or
towards the evening
10 lux switches at twilight
5 lux switches upon darkness
Set follow-up time
The light is switched on for this time The follow-up time is set in a range from approx.
12 seconds to 12 minutes.
o Turn adjuster TIME (9) to the appropriate position (picture 2).
CAUTION!
Heat radiation too high.
Destruction of the sensors.
Align the device so that no direct sunshine hits the sensor window.
Do not place the device in the sun.
3/10
82508413
J:0082508413 18.08.2010
Observer 110
picture 3: Aligning the sensor head
Aligning the sensor head
For optimal alignment of the detection area the sensor head can be adjusted in three axes.
o Slacken central screw (6) somewhat (picture 3).
o Slew the sensor head. The scale (10) serves as an aid to orientation (picture 3).
o Tighten central screw.
o Slacken manual knob (5) (picture 3).
o Incline the sensor head (3).
i If the heavy marks of the scale (11) are aligned with each other, the inclination is
approx. 14 °. (picture 3). The farther the sensor head is inclined, the shorter is the range.
o Tighten manual knob (5).
o Turn the sensor head (3) (picture 3). The adjustment is detented; each detent corresponds
to approx. 10 °.
Limiting the detection area to the side
picture 4: Detection area with cover plate A
4/10
82508413
J:0082508413 18.08.2010
Observer 110
The detection area of the motion sensor can be limited to the side using the included cover
plate A.
o Fit cover plate A(picture 4).
Reducing the detection area to one level
picture 5: Detection area with cover plate B
Cover plate B masks out the two lower detection levels (picture 5).
o Fit cover plate B.
5 Information for qualified electricians
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
CAUTION!
Heat radiation too high.
Destruction of the sensors.
Align the device so that no direct sunshine hits the sensor window.
Do not place the device in the sun.
5/10
82508413
J:0082508413 18.08.2010
Observer 110
picture 6: Direction of motion
Selecting the installation location
o Select a vibration-free installation location; vibrations can lead to unwanted switching.
o Avoid interference sources. Interference sources, e.g. heaters, ventilation, air conditioners,
and cooling light bulbs can lead to unwanted switching.
o Take direction of motion into account.
i Motions that are transverse to the motion detector, direction of motion I can be detected
more easily than motions towards or away from the motion detector, direction of motion II
(picture 6)
o Determine installation height (picture 6) III.
i The effects of weather, e.g. rain, fog or snow can reduce the range.
Installing the connection box
picture 7: Connection box
(1) Connection box
(12) Fastening holes
(13) Cable entry
6/10
82508413
J:0082508413 18.08.2010
Observer 110
(14) Surface-mounted cable entry
(15) Condensation hole
(16) Central fastening dome
(17) Terminals
o Slacken manual knob (5).
o Incline sensor head and slacken central screw (6).
Cable entry from below.
o When the connecting cable is laid on the surface, open cable entry (14) in the connection
box.
o Unless installing in dusty areas, break out the condensation hole (15) in the connection
box.
o Fasten connection box using suitable screws.
Connecting the controller
picture 8: Connection diagram
(3) Sensor head
(17) Terminals
(18) Installation button, NC contact
o Connect sensor head and optional installation button according to connection diagram .
Terminal assignments for the sensor head
black, BK External conductor
brown, BN Switched external conductor
blue, BU Neutral conductor
Fastening sensor head on connection box
o Set sensor head (3) on connection box (1). When doing so, do not damage any cables.
o Fix sensor head (3) by tightening central screw (6).
7/10
82508413
J:0082508413 18.08.2010
Observer 110
Connecting controllers in parallel
picture 9: Connecting controllers in parallel
o Connect controller and optional installation button according to connection diagram
(picture 9).
5.2 Commissioning
Checking the detection area
o Switch on test operation (see chapter 4. Operation).
o Pace off the detection area, paying attention to reliable detection and interference sources.
o If necessary, limit the detection area to mask out interference sources. To do this, adjust
the sensor head or use a cover plate (see chapter 4. Operation).
Making operation settings
For detailed information, see the chapter Operation (see chapter 4. Operation).
o Switch on automatic mode.
o Set brightness threshold.
o Set follow-up time.
6 Appendix
6.1 Technical data
Rated voltage AC 230 V ~
Mains frequency 50 Hz
Power consumption approx. 1.3 W
Ambient temperature -35 ... 50 °C
Protection rating IP 54
Circuit breaker max. 10 A
Installation height 2.5 m
Detection angle approx. 110 °
Range approx. 16 m
Follow-up time approx. 12 s ... 12 min
Follow-up time (test) approx. 1 s
Lockout time approx. 2 s
Brightness setting approx. 5 ... 300 lx (and day operation)
Connected load
Incandescent lamps 2200 W
HV halogen lamps 1000 W
8/10
82508413
J:0082508413 18.08.2010
Observer 110
Tronic transformers Type-dependent
Electronic ballast Type-dependent
Switching current
Ohmic 10 A
inductive 0.5 A (cos φ = 0.5)
Switch-on current max. 16 A
Contact type µ contact
Connection
Single stranded max. 2.5 mm²
Total length power cable max. 100 m
6.2 Troubleshooting
Controller does not switch on
The ambient brightness is greater than the set brightness threshold.
Set brightness threshold using adjuster LUX(see chapter 4. Operation).
Detection area is limited.
Align sensor head or adapt cover plate (see chapter 4. Operation).
Controller switches on, even though it is bright enough even without lighting.
Controller is in test operation
Switch off test operation by turning middle adjuster to ON.
Adjuster LUX is at the left-hand end stop, the motion detector switches independently of the
brightness.
Set brightness threshold using adjuster LUX(see chapter 4. Operation).
Controller switches on without detected motion
Interference sources in the detection area, e.g. ventilation, cooling light bulbs, trees and
bushes.
Limit the detection area by aligning the sensor head or fitting a cover plate (see chapter 4.
Operation).
Controller switches off despite motion
Detection area is limited.
Align sensor head or adapt cover plate (see chapter 4. Operation).
Controller does not switch off after the set follow-up time has elapsed
Controller detects motions constantly. Pay attention to interference sources, e.g. ventilation,
cooling light bulbs, trees and bushes in the detection area.
Limit the detection area by aligning the sensor head or fitting a cover plate (see chapter 4.
Operation).
9/10
82508413
J:0082508413 18.08.2010
Observer 110
6.3 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
We provide a warranty as provided for by law.
Please send the unit postage-free with a description of the defect to our central customer
service office:
ALBRECHT JUNG GMBH & CO. KG
Service Center
Kupferstr. 17-19
D-44532 Lünen
Service-Line: +49 (0) 23 55 . 80 65 51
Telefax: +49 (0) 23 55 . 80 61 89
General equipment
Service-Line: +49 (0) 23 55 . 80 65 55
Telefax: +49 (0) 23 55 . 80 62 55
KNX equipment
Service-Line: +49 (0) 23 55 . 80 65 56
Telefax: +49 (0) 23 55 . 80 62 55
The Πsymbol is a free trade symbol, which is solely intended for the authorities and does not
guarantee any properties.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
D-58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-1 89
E-mail: [email protected]
Internet: www.jung.de
www.jung-katalog.de
10/10
82508413
J:0082508413 18.08.2010
Observer 110
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Jung Capteur de sécurité
Jung
Jung Observer 70 Manuel utilisateur
Jung
Jung FPM360WW Manuel utilisateur
Jung
Jung DWPM17360AL Manuel utilisateur
Jung
Jung FM ES 36804 REG Manuel utilisateur
Jung
Jung Standard 3361 WW Manuel utilisateur
Jung
Jung 3361WW-01 Manuel utilisateur
Jung
Jung 2103 REG ES Manuel utilisateur
Jung
Jung PMU 360 WW Manuel utilisateur
Jung
Jung Mini basic Manuel utilisateur
Jung
Jung FMDW360WW Manuel utilisateur
Jung
Jung 3361MWW Manuel utilisateur
Jung
Jung DWPMK360WW Manuel utilisateur
Jung
Jung BM 240 S1A WW Manuel utilisateur
Jung
Jung BM360MBWW Manuel utilisateur
Jung
Jung 3360 Manuel utilisateur
Jung
Jung 17180 Series Manuel utilisateur
Jung
Jung Radio Detector 180 Manuel utilisateur
Jung
Jung HOME BT 17181 Series Manuel utilisateur
Jung
Jung BT 17182 Series Manuel utilisateur
Jung
Jung Observer 220 Manuel utilisateur
