Johny AK/12 AUT Manuel
BLENDER ΑΚ/12 AUT
OPERATION & MAINTENANCE MANUAL
KIOSIDIS PRIVATE COMPANY P.C., COMMERCIAL BAR EQUIPMENT
16
th
km THESSALONIKI – SERRES, P.O. BOX 21,
572 00 LITI, THESSALONIKI,GREECE
ΤEL.: ( 30 23940) 73536 & 73537, FAX: ( 30 23940) 73538
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
2
TABLE OF CONTENTS
1. ABOUT YOUR BLENDER ...................................................................................... 3
2. SYMBOLS USED .................................................................................................... 3
3. FIELD OF USE ........................................................................................................ 3
3.1 Application Sector ............................................................................................... 3
4. INTRODUCTION TO THE MANUAL ...................................................................... 4
5. RULES FOR SAFE OPERATION ........................................................................... 5
6. SAFETY MEASURES AND GENERAL INSTRUCTIONS ...................................... 6
7. TRANSPORTATION, INSTALLATION AND CONNECTION ................................. 6
7.1 Transportation .................................................................................................... 6
7.2 Installation .......................................................................................................... 6
7.3 Connection ......................................................................................................... 7
7.4 Maximum Dimensions ........................................................................................ 9
8. MARKING ............................................................................................................. 1
8.1 Manu acturer Label & Technical In ormation o the Blender ............................. 10
8.2 Marking Signs ................................................................................................... 11
8.3 Warnings .......................................................................................................... 11
9. TECHNICAL CHARACTERISTICS ....................................................................... 11
1 . DESCRIPTION .................................................................................................... 12
10.1 Blender Parts .................................................................................................. 12
10.2 Control Panel .................................................................................................. 13
11. OPERATION ....................................................................................................... 15
11.1 Steps be ore irst use ...................................................................................... 15
12. CLEANING – MAINTENANCE ........................................................................... 16
12.1 Cleaning Instructions ...................................................................................... 16
13. WHEN NOT IN USE ............................................................................................ 18
13.1 Package – Storage – Recycling ...................................................................... 18
14. MALFUNCTIONS AND TROUBLESHOOTING .................................................. 19
15. SPARE PARTS ................................................................................................... 2
15.1 Exploded View ................................................................................................ 20
15.2 Spare Parts Index ........................................................................................... 21
16. ELECTRICAL DRAWING ................................................................................... 23
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
3
1. ABOUT YOUR BLENDER
Thank you for selecting the ΑΚ/12 John blender. You can use the
blender to prepare milkshakes, cocktails, cold soups etc. The blender is
a laborious, robust and long-lasting heavy duty appliance.
2. SYMBOLS USED
This safety symbol is followed by a message relative to dangers
that should be taken into consideration for the avoidance of an accident.
This symbol is followed by a message relative to information, re-
ported in the present manual or in an accompanying handbook and
should be taken into consideration.
This symbol is followed by a suggestion.
When you see one of the above, pay attention to any warnings or points
important for the operation and read carefully the message that follows.
3. FIELD OF USE
3.1 Application Sector
This blender is made for professional and catering use in places such
as coffee shops, hotels and restaurants.
ATTENTION! The appliance should be operate only by authorized
staff.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
4
4. INTRODUCTION TO THE MANUAL
We recommend you to read this manual carefully before the first use.
We prepared it in order for you to use it right and receive the best per-
formance. The present manual refers to the use and maintenance of the
electric blender ΑΚ/12 John , and aims to help the blender’s best opera-
tion. Guarantee is also included with the terms and conditions that make
it valid.
«KIOSIDIS PRIVATE COMPANY P.C.» does not have any responsi-
bility for accidents or damages caused by carelessness or nonob-
servance of the instructions of the specific manual. The company does
not have any responsibility for damages caused by inappropriate use of
the blender.
ATTENTION! The present manual is an integral part of the blend-
er ΑΚ/12 John and should always accompany it in every transfer or re-
sale. The staff should always keep it in safe place. The staff is also re-
sponsible for manual’s storage and to keep it in good condition, so that
they can consult it during the blender’s lifetime. In case of loss or de-
struction of the manual, a new copy has to be asked immediately from
your supplier.
Retain the present manual meticulously in an ideal place close to
anyone related to the appliance.
Never neglect to read the manual, no matter your previous experi-
ence. Few minutes of study might save you time and/or money.
Read carefully before you start up procedure, operation, mainte-
nance or any other interruptions to the appliance and follow the below
mentioned directions and warnings precisely.
Only authorized personnel, properly trained for its operation,
should work on this appliance. With trained and well-informed personnel
you shall avoid dangers that the operation could create.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
5
5. RULES FOR SAFE OPERATION
ATTENTION! Disobedience of the following rules may cause ac-
cident and possible injure.
♦ The authorized operator should read this instruction manual thorough-
ly and follow the instructions as they are referred in the present hand-
book.
♦ During operation make sure that there is no unauthorized personnel
on site. Children or handicapped people are not allowed to use the
blender.
♦ Do not remove the bowl unless the blender is completely stopped.
♦ Always wait for the blender to stop before you open the bowl’s cover.
♦ Do not try to reach the interior of the bowl during operating.
♦ Do not leave the blender connected to the mains power supply and
unattended at the end of your work, or during cleaning and in case of
malfunction or damage.
♦ Do not stretch the power cord.
♦ Do not use the blender if you notice any malfunction or any operation
problem or if the cord and /or the plug have any problem. Contact
your supplier for more information.
♦ Do not trust the repair and maintenance of your blender to people who
are not authorized by the manufacturer. Contact your supplier for
more information.
♦ Do not proceed to changes related to the blender whatsoever.
♦ Use only spare parts supplied by the manufacturer.
♦ Do not wet the blender parts with water or any other liquid, except for
the bowl.
♦ Never fill the bowl with very hot liquids or with solid ingredients without
a liquid base.
♦ Do not use the blender with empty bowl.
♦ Do not replace the cord by yourselves.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
6
6. SAFETY MEASURES AND GENERAL INSTRUCTIONS
The electric blender ΑΚ/12 John is designed, manufactured and as-
sembled according to the directions:
(LVD) Low Voltage 2014/35/EU
(EMC) Electromagnetic Compatibilit 2014/30/EU
(RoHS) Restriction of Hazardous Substances 2015/863/EU amend-
ing 2011/65/EU
7. TRANSPORTATION, INSTALLATION AND CONNECTION
7.1 Transportation
The blender ΑΚ/12 John is transported packed until its initial place-
ment. After the blender is unpacked it is carried by a person since the
appliance is portable. Total weight of the appliance is 5.050 gr.
Use transportation vehicle to transport the appliance when
packed.
When you receive the blender, check for any damages caused
during transport.
7.2 Installation
♦ The blender should be placed on a flat, smooth and steady sur-
face, so that there will be no risk for the blender to lose its stability after
installation.
♦ Always place it indoors at a room temperature of around 25
o
C
(maximum operation temperature 35
o
C). The place must be adequately
ventilated and well lit. Good ventilation is a basic requirement for the in-
stallation place.
♦ The place should be clean, free from water and oil residues.
♦ It should be connected to the mains power supply using only a
socket (“Deep Hole” type) connected to a stable current supplier. It is
recommended not to use extensions for the power supply cord.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
7
♦ The appropriate installation of current supply should be provided
for the appliance’s operation.
♦ The installation place should have the appropriate dimensions.
Around the appliance free space should exist, so that filling, supply, op-
eration, control and maintenance of the appliance is not prevented.
ATTENTION! Grounding is required at the socket.
ATTENTION! The voltage of the main electric circuit should be
compatible with the voltage referred at the technical information label of
the appliance.
ATTENTION! During the installation or moving of the blender, the
appliance must be unplugged and disconnected from the current.
Before installation the following information must be taken into con-
sideration:
♦ Initially check voltages and power requirements for the mains
connection.
♦ Fuse 7 Α.
On the site of operation the following should exist:
♦ Power supply 220-240 V, frequency 50/60 Hz.
♦ Fire extinguishing installation (as required by the local fire de-
partment for the safety of the premises).
ATTENTION! Protect the power supply cord from possible dam-
ages.
7.3 Connection
The appliance has to be connected to the mains socket. The end of
the electric cord has a plug that should be connected to a socket with the
same characteristics.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
8
ATTENTION! For your own safety before connecting the blender
to the mains check if:
♦ The connection of the phases and the grounding are accom-
plished. Earthed cord is yellow – green with wrapped insulation.
♦ The suitability of the supply wire is certified.
♦ Operation voltage and frequency are compatible with the charac-
teristics of the socket.
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
9
7.4 Maximum Dimensions
Picture 1: Maximum dimensions
Maximum dimensions (mm)
Length (L) 245 mm
Height (H) 450 mm
Width (W) 180 mm
Operation and maintenance manual
Blender AK/12 AUT Johny
KIOSIDIS PRI ATE COMPANY P.C. Commercial Bar Equipment
10
8. MARKING
By the term marking we define all the indications or signs for the
identification of the appliance or one of its parts placed by the manufac-
turer.
Each blender has been manufactured with all the safety measures for
the operator’s protection.
8.1 Manufacturer Label & Technical Information of the Blender
Manufacturer label and technical information of the appliance are
shown at a visible and readable point on the appliance and contains
phone numbers of the manufacturing company (Trade name, address,
postal code, phone & Fax), year of manufacture, type and model of the
appliance, serial number, power, voltage and electricity frequency as well
as CE marking.
Picture 2: Label with technical characteristics
Table des matières
