Johnson Controls EDA-8102 Instructions de montage
Installation Sheet
Issue Date 0392
1
1. EDA-8102-1100 Electric Damper Actuator with counterclockwise
spring return, or
EDA-8102-1101 Electric Damper Actuator with clockwise spring
return
2. Two #10 mounting screws
3. Two isolator grommets
ςscrewdriver, flat blade, 1/4 to 5/16 inch and 1/8 inch tips
ςdrill, 5/32 inch (4 mm) drill bit, 1-1/4 inch hole saw
ςadjustable wrench
ςpliers
Figure 1: Electric Damper Actuator
1. Compatibility and torque:
ςuse on dampers having 10 to 12 mm (0.394 to 0.472 inch) square
or 7/16 to 1/2 inch (11 to 12.5 mm) round shafts
ςcompatible with Johnson Controls D-1300 Blade Dampers
ςdelivers 100 in.lb of stall torque
2. Mounting requirements:
ςmounts in any orientation
ςduct or wall must be 16 gauge (0.06 inch or 1.5 mm) or thicker
Note: Order the Universal Mounting Bracket (D-3153-105) to mount on
duct or wall less than 16 gauge.
EDA-8102 Electric Damper Actuator
Kit Includes
Tools Required
Installation
Overview
EDA-8102 Electric Damper Actuator
1. Follow NEC and local electrical codes.
2. Disconnect all power supplies.
3. Observe ranges and limitations for individual model.
4. Do not install the actuator in applications where its failure could result
in personal injury and/or loss of property.
5. Do not install if explosive vapors, corrosive vapors, or escaping gases
will be present.
6. Add protective control devices as needed to prevent undesirable
system failure modes.
For#10 Mounting
Screw(6places)
2.33
(59)
2x1.50
2x0.75
6.94
(235)
8.78
(223)
9.26
(235)
4.65
(118)
Figure 2: Top View Dimension inches
mm
Mounting Caution
Pre-Mounting
EDA-8102 Electric Damper Actuator 3
4.34
(110)
6 in. min*
(3x 0.875)
for 1/2 in. conduit
Rubber Grommet
(2 Required)
* Six inch minimum required for cover removal, field wiring, and field adjustments.
Figure 3: End View Dimension inches
mm
Note: Before starting the job, obtain the damper installation information
to use as a reference when mounting the actuator.
1. Locate the preferred driving blade on the damper.
2. Cut a 1-1/4 inch (32 mm) hole in the duct or wall over the driving
blade pin.
3. Attach the drive pin extension to the drive pin and secure using the
clip provided.
4. Firmly grasp the drive pin extension with a pliers and manually close
the damper blades.
RetainerClip
Drive PinExtension
Figure 4: Rotation.
5. Note which direction closes the damper, clockwise (CW) or
counterclockwise (CCW).
EDA-8102 Electric Damper Actuator
Figure 5: Removing Cover
6. Insert a screwdriver under the edge of the plastic cover to gently pry
off the cover. See Figure 5.
7. Verify the mode of operation for the proper model number from
Table 1.
Table 1: Operation Modes
Product Code
No. Drive
Type Travel
Time Spring
Return
EDA-8102-1100 proportional 180 second counterclockwise
EDA-8102-1101 proportional 180 second clockwise
Note: The actuator can be mounted in any orientation.
1. Position the actuator onto the drive pin extension so that the actuator
sits against the duct.
2. Use of the actuator’s center mounting slots with the isolation
grommets is the preferred mounting arrangement. If the duct or wall
is less than 16 gauge (0.06 inch or 1.5 mm), order and use the
Universal Mounting Bracket (D-3153-105).
Note: Because of eccentric motion of the actuator that occurs when using
shafts smaller than 10 mm (0.394 inch) square or 1/2 inch
(12.5 mm) round, use of the isolation grommets in the center
mounting slot is required.
3. Mark the location of the actuator's top and bottom mounting slots on
the duct or wall.
4. Remove the actuator and set aside.
5. Drill 5/32 inch (4 mm) holes in the duct or wall at the marked
locations.
Mounting
EDA-8102 Electric Damper Actuator 5
6. Slide the actuator onto the drive pin extension.
7. Secure the actuator to the wall or duct with the screws and insulators
included in the kit.
8. Tighten the two square-head screws on the actuator coupler.
Note: The cover should remain off until the wiring is completed.
!
CAUTION: Disconnect all power before wiring the actuator to
avoid electrical shock or damaging the equipment.
Conduit Opening Opening Covers
Figure 6: Conduit Openings
1. Insert the leads from the controller through one of the three openings.
2. Install the black plugs in the other two conduit openings. See
Figure 6.
InputVoltage
Common
24 VACInputPower
+15 VOutputSupply
Slidewire
AuxiliaryInput
ACCOMIN
+15
+1
AUXIN
TB1
TB2
Figure 7: Wiring Connections
3. Connect the leads to Terminal Block 1 (TB1) as shown in Figure 7.
Wiring
EDA-8102 Electric Damper Actuator
TB1
TB2
I
V
W2
DCW
DCCW
W1
Figure 8: Jumper Locations
4. Set jumper at location W2 to match the control signal that will be
used. Jumper settings are defined in Table 2 below and shown in
Figure 8.
Table 2: Jumper Settings
Operating Mode W2 Jumper Setting
Voltage V
Current I
Slidewire V
Note: The EDA-8102 is factory set for 90° of rotation and a voltage
control signal of 1 to 9 VDC. To change these settings, see the
section Changing Rotation To Less Than 90° or the appropriate
signal calibration.
1. Apply power to the unit.
2. Refer to the controller's manual for directions on checking out a newly
installed device.
3. Use the controller to drive the actuator fully clockwise and
counterclockwise.
4. Verify that the damper blades fully open and close.
5. Install the plastic cover.
Checkout
Procedure
EDA-8102 Electric Damper Actuator 7
The EDA-8102 is factory set for 90° of rotation and a control signal of 1
to 9 VDC. If the amount of rotation or the control signal must be changed
from factory settings, use the following procedures. Refer to Figure 7 for
the location of the potentiometer and terminal blocks in the procedures.
Figure 9: Rotation Setting
1. Verify jumper W2 is set to the voltage (V) position.
2. Verify jumper W1 is set in the desired position:
DCW for clockwise driven rotation.
DCCW for counterclockwise driven rotation.
Note: Spring return direction is NOT reversible.
3. Turn the offset potentiometer (R39) to its mid-position.
4. Turn the span potentiometer (R35) fully counterclockwise.
5. Turn the CCW potentiometer (R36) fully clockwise.
6. Connect a jumper from terminal IN (TB1) to terminal +15 (TB2) as
shown in Figure 9. The actuator rotates until the end stop is reached.
7. Slowly adjust the stroke potentiometer (R37) until the actuator rotates
to the desired end stop position.
8. Remove the jumper between terminal IN and +15.
Field Adjustments
Changing Rotation
to Less Than 90°
Span
(R35)CCW
(R36)
Stroke
(R37)Offset
(R39)
TB1
TB2
I
V
W2
AC
COM
IN
+15
+1
AUXIN
TB1TB2
DCW
DCCW
W1
EDA-8102 Electric Damper Actuator
AC
COM
IN+15 +1
AUXI
N
TB1TB2
Figure 10: End Stop Connection
9. Connect terminal IN to COM (TB1) as shown in Figure 10. The
actuator will rotate until the end stop is reached.
10. Slowly adjust the CCW potentiometer (R36) until the actuator rotates
to the desired position.
11. Remove the connection between terminals IN and COM (TB1).
Note: Calibration of offset and span is required after changing rotation.
Depending on controller application, proceed with the appropriate
calibration procedure.
EDA-8102 Electric Damper Actuator 9
Span
(R35)
CCW
(R36)
Stroke
(R37) Offset
(R39)
TB1TB2
I
V
W2
0 to 15 VDC
Input
Common
Figure 11: Voltage Mode Connection
1. Verify that jumper W2 is set to the voltage (V) position.
2. Turn the span potentiometer (R35) fully clockwise.
3. Connect the input voltage (0 to 15 VDC) between terminals IN (+) and
COM (-) on TB1.
4. Apply the starting voltage.
5. Adjust the offset potentiometer (R39) until the actuator just begins to
move.
6. Apply the full span voltage.
7. Adjust the span potentiometer (R35) until the actuator reaches its
desired limit.
8. Remove external connections and install the cover.
Voltage Mode
Calibration
EDA-8102 Electric Damper Actuator
Span
(R35)
CCW
(R36)
Stroke
(R37) Offset
(R39)
TB1
TB2
I
V
W2
0 to 20 mA
Input
Common
Figure 12: Current Mode Connection
1. Verify that jumper W2 is set to the current (I) position.
2. Turn the span potentiometer (R35) fully clockwise.
3. Connect the input current (0 to 20 mA) to terminals AUXIN (+) on
TB2 and COM (-) on TB1.
4. Apply the starting current.
5. Adjust the offset potentiometer (R39) until the actuator just begins to
move.
6. Apply full current.
7. Adjust the span potentiometer (R35) until the actuator reaches its
desired limit.
8. Remove external connections and install the cover.
Current Mode
Calibration
Autres manuels pour EDA-8102
1
Autres manuels Johnson Controls Contrôleurs
Johnson Controls
Johnson Controls M9200 Series Manuel utilisateur
Johnson Controls
Johnson Controls tyco iSTAR Edge G2 Manuel utilisateur
Johnson Controls
Johnson Controls Penn A421 Series Manuel utilisateur
Johnson Controls
Johnson Controls METASYS VAV110 Manuel utilisateur
Johnson Controls
Johnson Controls VMA1615 Manuel utilisateur
Johnson Controls
Johnson Controls LX Series Manuel utilisateur
Johnson Controls
Johnson Controls VA-7481-0011 Manuel utilisateur
Johnson Controls
Johnson Controls PENN ACT2 Manuel de service
Johnson Controls
Johnson Controls DS-3153 Manuel utilisateur
Johnson Controls
Johnson Controls FEC26 Series Manuel utilisateur
Johnson Controls
Johnson Controls RRS Economizer Controller Manuel utilisateur
Johnson Controls
Johnson Controls UZC-256 Manuel utilisateur
Johnson Controls
Johnson Controls TEC3010 Manuel utilisateur
Johnson Controls
Johnson Controls P266 Series Manuel utilisateur
Johnson Controls
Johnson Controls FX80 Manuel utilisateur
Johnson Controls
Johnson Controls M91 GDA-1N Series Manuel utilisateur
Johnson Controls
Johnson Controls M9106 Series Manuel utilisateur
Johnson Controls
Johnson Controls CK721-A Manuel utilisateur
Johnson Controls
Johnson Controls M9204-B 2Z Series Manuel utilisateur
Johnson Controls
Johnson Controls M9316-A Z Series Manuel utilisateur
