Johnson Controls Tyco Kantech KT-400 Guide de démarrage rapide

Application Note

Connecting an OSDP HID reader to a KT-400 controller

Use this application note to wire a HID reader using OSDP protocol to a KT-400 controller

and to configure the setup in EntraPass.

Requirements

•KT-400 Controller firmware 3.00.07 or higher

•EntraPass Special, Corporate, or Global Edition 8.40 or later

•HID Reader with OSDP communication

•HID Reader Manager mobile application

•Mobile device with Bluetooth

Note: Kantech have implemented Open Supervised Device Protocol (OSDP) 2.2. OSDP is

an access control communications standard developed by the Security Industry Association

(SIA). For more information about the protocol, refer to

https://www.securityindustry.org/industry-standards/open-supervised-device-protocol/.

Wiring the HID reader to the KT-400 controller

Use the RS-485 COM (COM2) port for OSDP communication.

1. Disconnect the power to the KT-400 controller.

2. Connect the reader’s red wire to the +12VDC.

3. Connect the reader’s black wire to the earth ground GND.

4. Connect the reader’s white wire to the COM 485 +.

5. Connect the reader’s green wire to the COM 485 -.

For more information about installing and wiring the KT-400 controller, refer to the KT-400

Four-Door Controller Installation Guide.

Configuring the card reader using the HID mobile app

Use the HID Reader Manager mobile application to set up the HID card reader.

1. Install the HID Reader Manager app on a device that has Bluetooth.

2. Open the app and tap Scan For Readers.

3. Tap the reader that you want to configure.

4. Tap Software and tap Configure.

5. Tap Inspect. Follow the instructions on the screen.

6. Tap Detailed Configuration and tap Communication Protocol.

7. Tap Host Protocol and enable OSDP.

8. In the ADDRESS field, enter an address. Addresses start at 0 in EntraPass. Refer to

your EntraPass system for the next available address.

9. Tap ADD TO TEMPLATE.

10. In the OSDP BAUD RATE field, enter the baud rate that you configured in

EntraPass.

Application Note D29011149R001

11. Click Apply Selected Items.

For more information about installing and using the mobile app, refer to the HID© Signo™

Reader Installation Guide and the HID© Reader Manager™ Solution User Guide.

Configuring the HID reader in EntraPass

1. On the EntraPass workstation, click the Devices tab, and click Controller.

2. From the Controller list, select the controller you have connected the HID reader to.

3. In the Controller window, click the KT-400 tab.

4. From the COM2 Protocol list, select OSDP. The RS-485 baud rate changes to 9600

and the Reader template changes to Default OSDP reader template. You can

update these items.

5. Complete one of the following options:

•To manually add readers, complete the following steps:

a. Click the OSDP tab.

b. Click Add and, in the Address column, select or type the OSDP reader

address. Accepted values range from 0 to 126.

c. In the Door column, select the door to associate with the reader.

d. Click Save.

Note: This is the recommended option.

•To add unassigned readers automatically, complete the following steps:

a. On the Controller window toolbar, click the Request unassigned modules

icon.

b. In the Request unassigned modules window, right-click the appropriate

reader and select Assign module.

c. Click Save.

Note: This feature works only for addresses 0 to 10 at the default baud rate of

9600.

For more information about setting up controllers and readers in EntraPass, refer to the

EntraPass Administration Guide.

trademarks of Johnson Controls.

Technical support contact telephone numbers: 1 450 444 2030. Toll free: 1 888 222 1560.

www.kantech.com

Autres manuels pour Tyco Kantech KT-400

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Johnson Controls Contrôleurs

Johnson Controls

Johnson Controls VMA1930 Manuel utilisateur

Johnson Controls

Johnson Controls M9204-B 2Z Series Manuel utilisateur

Johnson Controls

Johnson Controls FAC3613 Manuel utilisateur

Johnson Controls

Johnson Controls M9116-GG-1N4 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN P70 Series Manuel utilisateur

Johnson Controls

Johnson Controls FX-PCG26 Manuel utilisateur

Johnson Controls

Johnson Controls VA-7010 Series Manuel

Johnson Controls

Johnson Controls FEC26 Series Manuel utilisateur

Johnson Controls

Johnson Controls FEC26 Series Manuel utilisateur

Johnson Controls

Johnson Controls York YKN2Open board Manuel

Johnson Controls

Johnson Controls CIS01 Mode d’emploi

Johnson Controls

Johnson Controls York 366-70488 Mode d’emploi

Johnson Controls

Johnson Controls CIR01 Manuel utilisateur

Johnson Controls

Johnson Controls VA-9070 Series Manuel de service

Johnson Controls

Johnson Controls M9220-GG-3 Series Manuel utilisateur

Johnson Controls

Johnson Controls SMART EQUIPMENT VERASYS VEC100 Manuel utilisateur

Johnson Controls

Johnson Controls VA-8052 Manuel utilisateur

Johnson Controls

Johnson Controls FEC16 Series Manuel utilisateur

Johnson Controls

Johnson Controls FAC2612-1 Manuel utilisateur

Johnson Controls

Johnson Controls FX-PCV1656 Manuel utilisateur

Johnson Controls

Johnson Controls TEC3000 Series Manuel utilisateur

Johnson Controls

Johnson Controls FlexSys CB2 Manuel utilisateur

Johnson Controls

Johnson Controls Tyco KT-1 Manuel utilisateur

Johnson Controls

Johnson Controls BMMS-1P Instructions d'utilisation d'origine

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur