Johnson Controls EDA-8000 Instructions de montage

Installation Sheet

Issue Date 0392

1. EDA-8000-1100 Actuator

2. Two #10 mounting screws

3. Two isolator grommets

ςscrewdriver, flat blade, 1/4 to 5/16 inch and 1/8 inch tips

ςdrill, 5/32 inch (4 mm) drill bit, 1-1/4 inch (32 mm) hole saw

ςadjustable wrench

ςpliers

Figure 1: Electric Damper Actuator

1. Compatibility and torque:

ςuse on dampers having 10 to 12 mm (0.394 to 0.472 inch) square

or 7/16 to 1/2 inch (11 to 12.5 mm) round shafts

ςcompatible with Johnson Controls D-1300 Dampers

ςdelivers 100 in·lb of stall torque

2. Mounting requirements:

ςmounts in any orientation

ςduct or wall must be 16 gauge (0.06 inch or 1.5 mm) or thicker

Note: Order the Universal Mounting Bracket (D-3153-105) to mount on

duct or wall less than 16 gauge.

EDA-8000 Electric Damper Actuator

Kit Includes

Tools Required

Installation

Overview

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator

1. Follow NEC and local electrical codes.

2. Disconnect all power supplies.

3. Observe ranges and limitations for individual model.

4. Do not install the actuator in applications where its failure could result

in personal injury and/or loss of property.

5. Do not install if explosive vapors, corrosive vapors, or escaping gases

will be present.

6. Add protective control devices as needed to prevent undesirable

system failure modes.

For#10 Mounting

Screw(6places)

2.33

(59)

2x1.50

2x0.75

6.94

(235)

8.78

(223)

9.26

(235)

4.65

(118)

Figure 2: Top View Dimension inches

Mounting Caution

Pre-Mounting

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator 3

4.34

(110)

6 in. min*

(3x 0.875)

for 1/2 in. conduit

Rubber Grommet

(2 Required)

* Six inch minimum required for cover removal, field wiring, and field adjustments.

Figure 3: End View Dimension inches

Note: Before starting the job, obtain the damper installation information

to use as a reference when mounting the actuator.

1. Locate the preferred driving blade on the damper.

2. Cut a 1-1/4 inch (32 mm) hole in the duct or wall over the preferred

driving blade pin.

3. Attach the blade pin extension from the damper assembly to the drive

pin and secure using the clip provided.

4. Firmly grasp the drive pin extension with a pliers and manually close

the damper blades.

5. Note which direction closes the damper, clockwise (CW) or

counterclockwise (CCW).

Figure 4: Removing Cover

6. Insert a screwdriver under the edge of the plastic cover to gently pry

off the cover. See Figure 4.

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator

Release Lever

Figure 5: Release Lever Location

7. Slide the release lever up to disengage the gears as shown in Figure 5.

RetainerClip

Drive PinExtension

Figure 6: Rotation

8. Hold the release lever up and fully rotate the actuator coupler in the

same direction as step 4.

Note: For example, if the damper closed by rotating the extension pin

CW, rotate the actuator coupler fully CW until the end stop is

reached. See Figure 6.

Note: The actuator can be mounted in any orientation.

1. Position the actuator onto the blade pin extension so that the actuator

sits against the duct.

2. Use of the actuator’s center mounting slots with the isolation

grommets is the preferred mounting arrangement. If the duct or wall

is less than 16 gauge (0.06 inch or 1.5 mm), use the Universal

Mounting Bracket (D-3153-105).

Mounting

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator 5

Note: Because of eccentric motion of the actuator that occurs when using

shafts smaller than 10 mm (0.394 inch) square or 1/2 inch

(12.5 mm) round, use of the isolation grommets in the center

mounting slot is required.

3. Mark the location of the actuator's top and bottom mounting slots on

the duct or wall.

4. Remove the actuator and set aside.

5. Drill 5/32 inch (4 mm) holes in the duct or wall at the marked

locations.

6. Slide the actuator and coupler onto the drive pin extension.

7. Secure the actuator to the wall or duct with the screws and isolation

grommets included in the kit.

8. Tighten the two square-head screws on the actuator coupler.

9. Lift the manual release lever and hand turn the coupler CW and CCW

to check that the damper blades fully open and close.

Note: The cover should remain off until the wiring is completed.

CAUTION: Disconnect all power before wiring the actuator to

avoid electrical shock or damaging the equipment.

1. If the cover was replaced after installation, insert a screwdriver under

the edge of the plastic cover and carefully pry off the cover as shown

in Figure 4.

Conduit Opening

Opening Covers

Figure 7: Conduit Openings

2. Insert the leads from the controller through one of the three conduit

openings. Install the black plugs in the other two openings. See

Figure 7.

Wiring

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator

CCW

COM

TB1

FT1

Clockwise24 VAC

Counterclockwise24 VA

Common

Figure 8: Standard Wiring Connection

3. Connect the leads to Terminal Block 1 (TB1). See Figure 8.

1. Apply power.

2. Refer to the controller's manual for directions on checking out a newly

installed device. Use the controller to drive the actuator fully CW and

CCW. Verify that the damper blades fully open and close.

3. Install the plastic cover.

The EDA-8000 is not field repairable. For replacement, contact the

nearest Johnson Controls branch office or your wholesale distributor.

Checkout

Procedure

Replacement

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator 7

Notes

All manuals and user guides at all-guides.com

EDA-8000 Electric Damper Actuator

Notes

Controls Group

507 E. Michigan Street

P.O. Box 423

Milwaukee, WI 53201

All manuals and user guides at all-guides.com

Table des matières

Autres manuels Johnson Controls Contrôleurs

Johnson Controls

Johnson Controls M9220-GGx-3 series Manuel utilisateur

Johnson Controls

Johnson Controls M9316-A Z Series Manuel utilisateur

Johnson Controls

Johnson Controls F4-SNC Manuel utilisateur

Johnson Controls

Johnson Controls G76 Series Manuel utilisateur

Johnson Controls

Johnson Controls M9108-A-1N Series Manuel utilisateur

Johnson Controls

Johnson Controls PCV1617 Manuel utilisateur

Johnson Controls

Johnson Controls SNC Series Manuel utilisateur

Johnson Controls

Johnson Controls Hitachi C4IRK01 Manuel utilisateur

Johnson Controls

Johnson Controls TRUE RH HC-67x3 Manuel utilisateur

Johnson Controls

Johnson Controls VA-9070 Series Manuel utilisateur

Johnson Controls

Johnson Controls FX-PCV Series Manuel utilisateur

Johnson Controls

Johnson Controls VA-7480 Manuel utilisateur

Johnson Controls

Johnson Controls VA9310 Series Manuel utilisateur

Johnson Controls

Johnson Controls FW-14 Manuel utilisateur

Johnson Controls

Johnson Controls Penn A421 Series Manuel utilisateur

Johnson Controls

Johnson Controls S1-33103010000 Manuel utilisateur

Johnson Controls

Johnson Controls FEC26 Series Manuel utilisateur

Johnson Controls

Johnson Controls Metasys MS-FEU1610-0U Manuel utilisateur

Johnson Controls

Johnson Controls VA-8052 Manuel utilisateur

Johnson Controls

Johnson Controls M9102-AGA-2S Series Manuel utilisateur

Johnson Controls

Johnson Controls M9204-GG 2 Series Manuel utilisateur

Johnson Controls

Johnson Controls VFD66 Series Manuel

Johnson Controls

Johnson Controls LP-FX2211T-0 Manuel utilisateur

Johnson Controls

Johnson Controls LN Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur