Johnson Controls ATC1510 Manuel utilisateur
ATC1510 Advanced Terminal Unit Controller
Installation Guide
About This Product
The Advanced Terminal Unit Controller (ATC) runs
custom, freely-programmed applications, and provides
the inputs and outputs required to monitor and control
a wide variety of HVAC/R equipment.
The ATCs operate as BACnet® Application Specific
Controllers (B-ASC) and integrate into Johnson
Controls® and third-party BACnet systems.
Communication Protocols
You can configure the field bus communication
protocol in the ATC as a standard BACnet MS/TP device
or an N2 protocol device. You can use the Controller
Configuration Tool (CCT) to switch the communication
protocol. Switchable communication protocols provide
a cost-effective upgrade and modernization path for
customers with existing N2 controllers.
Compliance Information
This equipment has been tested and found to comply
with the limits for a Class A digital device pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when this equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area may cause
harmful interference, in which case the users will
be required to correct the interference at their own
expense.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Installation
Observe the following guidelines when installing an
ATC:
• To minimize vibration and shock damage to the
controller, transport the controller in the original
container.
• Verify that all parts shipped with the controller.
• Do not drop the controller or subject it to physical
shock.
Parts Included
• One Advanced Terminal Unit Controller
• One installation instruction guide
• 10 cable ties
• One multi-language warning sheet
Accessories
Table 1: Accessories
Product Code Number Description
LC-IP20 IP20 Terminal Cover Kit
Required Materials and Special Tools
• Three fasteners appropriate for the mounting
surface (M4 screws or #8 screws)
• One 20 cm (8 in.), or longer, piece of 35 mm DIN rail
and the appropriate hardware for DIN rail mount
• Small straight-blade screwdriver to secure the wires
in the terminal blocks
*241014302015—*
24-10143-02015 Rev —
2019-05-20
(barcode for factory use only)
LC-ATC1510-0
Mounting the Controller
This section describes how to mount the ATC.
1. Horizontally mount a 20 cm (8 in.) section of 35
mm (1.3 in.) DIN rail.
2. On the back of the controller, extend the two
mounting clips as illustrated.
3. Position the controller so that the two extended
mounting clips are facing downwards, and place
the controller on the DIN rail.
4. Push the bottom mounting clips up to secure the
controller on the DIN rail.
ATC1510 Advanced Terminal Unit Controller Installation Guide2
Wiring
The following procedure describes how to wire the
ATC. The ATC ports and buses are described in Figure 6.
CAUTION
Risk of Electric Shock
Disconnect the power supply before making electrical
connections to avoid electric shock.
ATTENTION
Risque de décharge électrique
Débrancher l'alimentation avant de réaliser tout rac-
cordement électrique afin d'éviter tout risque de
décharge électrique.
CAUTION
Risk of Property Damage
Do not apply power to the system before checking all
wiring connections. Short circuited or improperly con-
nected wires may result in permanent damage to the
equipment.
ATTENTION
Risque de dégâts matériels
Ne pas mettre le système sous tension avant d'avoir
vérifié tous les raccords de câblage. Des fils for-
mant un court-circuit ou connectés de façon incor-
recte risquent d'endommager irrémédiablement
l'équipement.
1. Wire the FC Bus Terminal Block. The ATC features
a blue, removable, 4-terminal FC Bus block that
fits into a board-mounted jack. Wire the FC bus as
shown in Figure 1.
Note: Controllers can be daisy-chained by
inserting two wires into each connection.
Figure 1: FC Bus Terminal Block Wiring
2. Wire the SA Bus Terminal. The ATC features a
brown, removable, 4-terminal SA Bus block that
fits into a board-mounted jack. Wire the SA Bus as
shown in Figure 2.
Note:
- SA bus devices can be daisy-chained
by inserting two wires into each
connection.
- The SA BUS PWR terminal on the ATC
supplies 15 VDC, up to 210 mA. The
SA BUS PWR terminal can be used to
connect the 15 VDC power leads on
the SA Bus to power other devices
that are connected in a daisy chain
configuration. If a device has an SA
BUS PWR output, do not connect it to
the ATC SA BUS PWR output.
ATC1510 Advanced Terminal Unit Controller Installation Guide 3
Figure 2: SA Bus Terminal Block Wiring
3. The SA Bus port on the controller is an RJ-12, 6-
position modular jack that provides a connection
for the Mobile Access Portal (MAP) Gateway, the
VAV Balancing Tool, specified network sensors, or
other SA Bus devices with RJ-12 plugs. Wire the SA
Bus port as shown in Figure 3.
Note: The SA port is connected internally to
the SA Bus terminal block.
Figure 3: Pin Number Assignments for SA Bus
Ports
4. Wire the Power Supply Terminal Block. The ATC
uses a 240 VAC, +/-10% supply power terminal
two-pin, three-position, red connector.
a. Connect the supply wires to the red plug-
in terminal block as shown in Figure 4.
b. Insert the plug-in terminal block into the
ATC. For the location of the ATC power
input, see Figure 6.
Figure 4: Power Supply Wiring
A: Line
B: Neutral
Maximum Cable Length versus Load Current
For this system to operate correctly, the maximum
wire length is 137.2 m (450 ft) and the wire cross-
sectional area is 1.5 mm2 (16 AWG) to 0.5 mm2 (22
AWG).
Input and Output wiring guidelines
Table 2 and Table 3 provide information and guidelines
about the functions, ratings, and requirements for the
controller input and output terminals, and guidelines
for determining proper wire sizes and cable lengths.
In addition to the wiring guidelines in Table 2 and Table
3, observe these guidelines when wiring controller
inputs and outputs:
• Run all low-voltage wiring and cables separate from
high-voltage wiring.
• All input and output cables, regardless of wire size
or number of wires, should consist of stranded,
insulated, and twisted copper wires.
• Shielded cable is not required for input or output
cables.
• Shielded cable is recommended for input
and output cables that are exposed to high
electromagnetic or radio frequency noise.
• Inputs/outputs with cables less than 30 m (100 ft)
typically do not require an offset in the software
setup. Cable runs over 30 m (100 ft) may require an
offset in the input/output software setup.
ATC1510 Advanced Terminal Unit Controller Installation Guide4
I/O terminal blocks, ratings and requirements
Table 2: I/O terminal blocks, functions, ratings, requirements, and cables
Terminal Block label Terminal
label Function, ratings, requirements Determine wire size and
maximum cable length
Analog Input - Voltage Mode (0–10 VDC)
10 VDC maximum input voltage
Internal 10k ohm Pull-down
See Guideline A in Table 3
Analog Input - Resistive Mode (0–600k ohm)
Internal 12 V. 15k ohm pull up
Qualified Sensors: 0-2k ohm potentiometer, RTD (1k Nickel
[ Johnson Controls® sensor], 1k Platinum, and A99B Silicon
Temperature Sensor) Negative Temperature Coefficient (NTC)
Sensor
See Guideline A in Table 3.INn
Binary Input - Dry Contact Maintained Mode
1 second minimum pulse width
Internal 12 V. 15k ohm pull up
See Guideline A in Table 3.
UNIVERSAL
(Inputs)
ICOMn
Universal Input Common for all Universal Input terminals
Note: All Universal ICOMn terminals share
a common, which is isolated from all other
commons.
Same as (Universal) INn
Binary Input - Dry Contact Maintained Mode
0.01 second minimum pulse width
Internal 18 V. 3k ohm pull up
INnBinary Input - Pulse Counter/Accumulator Mode
0.01 second minimum pulse width
(50 Hz at 50% duty cycle)
Internal 18 V. 3k ohm pull up
BINARY
(Inputs)
ICOMn
Binary Input Common for all Binary Input (IN) terminals
Note: All Binary ICOMn terminals share a
common, which is isolated from all other
commons, except the Configurable Output
(CO) common (OCOMn) when the CO is
defined as an Analog Output.
See Guideline A in Table 3.
Analog Output - Voltage Mode (0–10 VDC)
10 VDC maximum output voltage
10 mA maximum output current
Required an external load of 1,000 ohm or more.
See Guideline A in Table 3.
OUTn
Binary Output - 24 VAC Triac (External Power Source only)
Connects OUTn to OCOMn when activated.
External Power Source Requirements:
30 VAC maximum output voltage
0.5 A maximum output current
Maximum 6 cycles/hour with M9220BGx-3
40 mA minimum load current
See Guideline C in Table 3.
CONFIGURABLE
(Outputs)
OCOMn
Analog Output Signal Common All Configurable Outputs
(COs) defined as Analog Outputs (AOs) share a common,
which is isolated from all other commons except the Binary
Input common.
Binary Output Signal Common All Configurable Outputs
(COs) defined as Binary Outputs are isolated from all other
commons, including other CO commons.
Same as (Configurable) OUTn.
ATC1510 Advanced Terminal Unit Controller Installation Guide 5
Table 2: I/O terminal blocks, functions, ratings, requirements, and cables
Terminal Block label Terminal
label Function, ratings, requirements Determine wire size and
maximum cable length
OUTn
Binary Output - 24 VAC Triac (External Power Source)
Connects OUTn to OCOMn when activated.
External Power Source Requirements:
30 VAC maximum output voltage
0.5 A maximum output current
Maximum 6 cycles/hour with M9220BGx-3
40 mA minimum load current
BINARY
(Output)
OCOMn
Binary Output Common (for OUTn terminal)
Note: Each Binary Output Common terminal
(OCOMn) is isolated from all other commons,
including other Binary Output Common
terminals.
See Guideline C in Table 3.
OUTn
5 A Relay Output - Normally Open
Single-Pole, Single-Throw, Normally Open
240 VAC, 5 A Resistive, 50k cycles
240 VAC, 0.66FLA/4LRA, 50k cycles
BINARY RELAY 5A
(Output)
OCOMn
Binary Relay Output Common (for OUTn terminal)
Note: Each Binary Relay Output Common
terminal (OCOMn) is isolated from all other
commons, including other Binary Relay Output
Common terminals.
See Guideline C in Table 3.
OUTn
10 A Relay Output - Normally Open
Single-Pole, Single-Throw, Normally Open
240 VAC, 10 A Resistive, 100k cycles
BINARY RELAY 10A
(Output)
OCOMn
Binary Relay Output Common (for OUTn terminal)
Note: Each Binary Relay Output Common
terminal (OCOMn) is isolated from all other
commons, including other Binary Relay Output
Common terminals.
24VAC
24 VAC Output (for actuator power)
24 VAC, 500 mA
Same circuit as modules logic circuitry 24 VAC, SELV; Not-
limited power (>15 Watts) Class 2, 0.5 A
24VAC OUT
(Output)
COM
24 VAC Output Common
Note: The 24 VAC Output Common terminal
(COM) is isolated from all other commons.
See Guideline C in Table 3.
ATC1510 Advanced Terminal Unit Controller Installation Guide6
Cable and wire length guidelines
The following table defines cable length guidelines for the various wire sizes that may be used for wiring low-
voltage (<30 V) input and outputs.
Table 3: Cable length guidelines
Guideline1Wire size/Gauge and type Maximum cable length and
type Assumptions
1.0 mm2 (18 AWG) stranded copper 457 m (1,500 ft) twisted wire
0.75 mm2 (20 AWG) stranded copper
297 m (975 ft) twisted wire 297 m (975 ft) twisted wire
0.5 mm2 (22 AWG) stranded copper
183 m (600 ft) twisted wire 183 m (600 ft) twisted wire
A
0.25 mm2 (24 AWG) stranded copper
107 m (350 ft) twisted wire 107 m (350 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
1.0 mm2 (18 AWG) stranded copper 229 m (750 ft) twisted wire
0.75 mm2 (20 AWG) stranded copper
297 m (975 ft) twisted wire 137 m (450 ft) twisted wire
0.5 mm2 (22 AWG) stranded copper
183 m (600 ft) twisted wire 91 m (300 ft) twisted wire
B
0.25 mm2 (24 AWG) stranded copper
107 m (350 ft) twisted wire 61 m (200 ft) twisted wire
100 mV maximum voltage drop
Depending on the cable length
and the connected input or
output device, you may have
to define an offset in the setup
software for the input or output
point.
C
See Figure 5 to select wire size/
gauge.
Use stranded copper wire.
See Figure 5 to determine cable
length.
Use twisted wire cable.
N/A
1 The required wire sizes and lengths for high-voltage (>30 V) Relay Outputs are determined by the load connected to the relay, and
local, national or regional electrical codes.
Maximum cable length versus load current
Use the following figure to estimate the maximum cable length relative to the wire size and the load current (in
mA) when wiring inputs and outputs.
Note: Figure 5 applies to low-voltage (<30 V)
inputs and outputs only.
Figure 5: Maximum wire length for low-voltage (<30 V) Inputs and Outputs by current and wire size
ATC1510 Advanced Terminal Unit Controller Installation Guide 7
Communications bus and supply power wiring guidelines
Table 4 provides information about the functions, ratings, and requirements for the communication bus and
supply power terminals. The table also provides guidelines for wire sizes, cable types, and cable lengths for wiring
the controller's communication buses and supply power.
In addition to the guidelines in Table 4, observe the following guidelines when you wire an FC or SA bus and the 24
VAC supply power:
• Run all low-voltage wiring and cables separate from high-voltage wiring.
• All FC and SA bus cables, regardless of wire size, should be twisted, insulated, stranded copper wire.
• Using shielded cable is best practice for all FC and SA bus cables.
• Refer to the MS/TP Communications Bus Technical Bulletin (LIT-12011034) for detailed information regarding wire
size and cable length requirements for FC and SA buses.
Table 4: Communications bus and supply power terminal blocks, functions, ratings, requirements, and
cables
Terminal block/
Port label
Terminal
labels Function, electrical ratings/Requirements Recommended cable type1
+
-FC Bus Communications
COM Signal Reference (Common) for Bus communications
FC BUS2
SHIELD Isolated terminal (optional shield drain connection)
0.5 mm2 (22 AWG) stranded, 3-wire
twisted, shielded cable recommended
+
-SA Bus Communications
COM SA Bus Signal Reference and 15 VDC Common
SA BUS2
PWR 15 VDC Supply Power for Devices on the SA Bus
(Maximum total current draw for the SA Bus is 210 mA.)
0.5 mm2 (22 AWG) stranded, 4-wire
(2 twisted-pairs), shielded cable
recommended.
Note: The + and - wire
are one twisted pair, and
the COM and SA PWR are
the second twisted pair of
wires.
SA BUS (Port)2SA BUS
RJ-12 6-Position Modular Connector provides:
SA Bus Communications
SA Bus Signal Reference and 15 VDC Common
15 VDC Power for devices on the SA bus and BTCVT or MAP
Gateway
24 AWG 3-pair CAT3 cable <30.5 m
(100 ft)
LINE 240 VAC Power Supply - Line
Supplies 240 VAC (50/60 Hz)
240VAC, 20VA
NEUTRAL 240 VAC Power Supply - Neutral
1.0 mm2
(18 AWG) 2-wire
1 See Input and Output wiring guidelines to determine wire size and cable lengths for cables other than the recommended cables.
2 The FC bus and SA bus wiring recommendations in this table are for MS/TP Bus communications at 38.4k baud. For more
information, refer to the MS/TP Communications Bus Technical Bulletin (LIT-12011034).
ATC1510 Advanced Terminal Unit Controller Installation Guide8
Termination details
A set of Johnson Controls termination diagrams provides details for wiring inputs and outputs to the controllers.
See the figures in this section for the applicable termination diagrams.
Table 5: Termination diagrams
Type of Field
Device
Type of Input/
Output Termination Diagrams
Temperature
Sensor UI
Voltage Input -
External Source UI
Voltage Input
(Self-Powered) UI
Current Input -
External Source
(Isolated)
UI
Current Input -
External Source (in
Loop)
UI
Dry Contact
(Binary Input) UI or BI
ATC1510 Advanced Terminal Unit Controller Installation Guide 9
Table 5: Termination diagrams
Type of Field
Device
Type of Input/
Output Termination Diagrams
0–10 VDC Output
to Actuator
(External Source)
CO
0–10 VDC Output
to Actuator
(Internal Source)
CO
Current Output CO
24 VAC Triac
Output (Switch
Low, External
Source)
CO
Incremental
Control to
Actuator (Switch
Low, Externally
Sourced)
(Triac Jumpers
where applicable)
BO
24 VAC Binary
Output (Switch
Low, Externally
Sourced)
(Triac Jumpers
where applicable)
BO
24 VAC Binary
Output (Switch
High, Externally
Sourced)
(Triac Jumpers
where applicable)
BO
ATC1510 Advanced Terminal Unit Controller Installation Guide10
Table des matières
Autres manuels Johnson Controls Contrôleurs
Johnson Controls
Johnson Controls VA7820-HG*-2 Series Manuel utilisateur
Johnson Controls
Johnson Controls FW-14 Manuel utilisateur
Johnson Controls
Johnson Controls VA-7700 Series Manuel utilisateur
Johnson Controls
Johnson Controls M9220-GGx-3 series Manuel utilisateur
Johnson Controls
Johnson Controls M9308-AGA-xZ series Manuel utilisateur
Johnson Controls
Johnson Controls BMMS-1P Instructions d'utilisation d'origine
Johnson Controls
Johnson Controls HS3032 Manuel utilisateur
Johnson Controls
Johnson Controls FX80 Manuel utilisateur
Johnson Controls
Johnson Controls G670 Instructions de montage
Johnson Controls
Johnson Controls VFD66 Series Manuel
Johnson Controls
Johnson Controls V-4000-1 Manuel utilisateur
Johnson Controls
Johnson Controls tyco iSTAR Edge G2 Manuel de l'opérateur
Johnson Controls
Johnson Controls UNT1100 Series Manuel utilisateur
Johnson Controls
Johnson Controls LP-FX2211T-0 Manuel utilisateur
Johnson Controls
Johnson Controls Hitachi C4IRK01 Manuel utilisateur
Johnson Controls
Johnson Controls TEC2245-4 Manuel utilisateur
Johnson Controls
Johnson Controls VA-7010 Series Manuel
Johnson Controls
Johnson Controls FX70 Manuel utilisateur
Johnson Controls
Johnson Controls EDA-8000 Manuel
Johnson Controls
Johnson Controls NXA-VAV-01 Manuel utilisateur
