Johnson Controls AIM-200 Manuel utilisateur

FC-2000 Technical Manual 406

Addressable Intelligent Module Section

Technical Bulletin

Issue Date 0794

Order No. 406-080

Introduction Page 3

Description 3

Inventory 4

Optional Peripherals 6

Installing the AIM-200 9

Wiring the Communications Loop Circuit 12

M500XJ Isolator Module 24

M500MJ Monitor Module 25

M501MJ Monitor Module 26

M500MJ and M501MJ Monitor Module Technical Notes 26

M510CJ Control Module 29

BGX-101 Addressable Manual Pull Station 33

Intelligent Detectors 34

Inserting the AIM-200 Cards 34

Programming the AIM-200 37

Programming Display 37

Auto-Program Mode 40

AIM-200 Power Requirements 41

Regulated Power Required in Standby 41

Regulated Power Required in Alarm 41

2Addressable Intelligent Module—AIM-200 Addressable Intelligent Module

AIM-200 Point Annunciation Page 43

Program Clear 44

Default Zone Map 45

Display Status 45

Program Edit 47

Alarm Bus 48

General Alarm Service 49

Backup Alarm Bus 50

Signal Silence Function 50

Operating M510CJ Control Modules 51

General Alarm 51

Control-by-Zone 52

Control-by-Module 52

Control-by-Detector 53

General M510CJ Trouble 53

Non-Silenceable Indicating Appliance Circuit 53

Non-Silenceable Form-C Relays 53

Supervisory Zones 53

Alarm Verification 54

Waterflow Zones 54

Walk Test 54

Trouble Condition 54

Step Switches 55

Loop Fault LED and RESET 55

ON-LINE LED and SKIP Switch 55

ENTER LED and Switch 55

Display Status LED and Switch 55

Automatic Detector Test 55

Operating the AIM-200 59

Zone Display 59

Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 3

Introduction

Note: AIM-200 features discussed in this document are available with

AIM-200 software part number 73264 or greater.

The Addressable Intelligent Module (AIM-200) functions as an interface

between the FC-2000 Fire Alarm Control Panel andintelligent/addressable

devices. To the FC-2000, the AIM-200 looks like an IZM-8 Initiating

Zone Module. On its single communications loop, the AIM-200 will

communicate with up to 99 addressable modules and 99 intelligent

detectors. The AIM-200 will communicate with the following:

2551J Intelligent Photoelectric Smoke Detector

1551J Intelligent Ionization Smoke Detector

5551J Intelligent Thermal Sensor

M500MJ Addressable Monitor Module

M502MJ Addressable Monitor Module

M501MJ Miniature Monitor Module

M510CJ Addressable Control Module

BGX-101L Addressable Manual Pull Station

DH-500J Intelligent Duct Detector Housing

The 198 devices are mapped into eight software zones by the AIM-200.

The status of these zones is reported to the CPU-2000. The AIM-200

includes a digital display for identifying the exact device address within a

zone. The display is also used to display device types and analog detector

sensitivity values.

Although the AIM-200 is intended primarily as an initiating input module,

it can support M510CJ Control Modules on the loop. The M510CJ

modules may be mapped to AIM-200 zones much like outputs are mapped

to inputs during standard FC-2000 programming.

The AIM-200 may be mixed in a system with any of these system modules:

IZM-8 Initiating Zone Module

IZE-A Initiating Zone Expander

ICM-4 Indicating Circuit Module

ICE-4 Initiating Circuit Expander

CRM-4 Control Relay Module

CRE-4 Control Relay Expander

Description

4Addressable Intelligent Module—AIM-200 Addressable Intelligent Module

VCM-4 Voice Control Module

VCE-4 Voice Control Expander

DCM-4 Dual Channel Module

TCM-2 Time Control Module (Single hazard release)

TCM-4 Time Control Module (Multiple hazard release)

In addition, ACM remote annunciators, AMG-1 and FFT-7

voice/telephone modules, and several power supplies can be employed with

an AIM-200.

Up to ten AIM-200s may be installed in one FC-2000 for a capacity of

1,980 points (subject to limitations of system power supply). Refer to the

AIM-200 Power Requirementssection of this document.

Figure 1: AIM-200 Addressable Intelligent Module

Inventory

AIM-200

Addressable

Intelligent Module

Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 5

The AIM-200 communicates with up to 99 intelligent detectors and up to

99 addressable modules. The AIM-200 reports device alarm or trouble

activity back to the CPU as one of eight mapped zones.

Figure 2: AIM-200 Label Inserts

The slide-in labels are printed with identification for system-defined LEDs

and switches. Space is provided to type in custom information for the

eight user-defined zones.

Figure 3: AIM-200 Card File

A special card file is attached to the bottom front of the AIM-200. Several

standard 4 in. by 2-1/4 in. cards are provided and may be marked with

device information by the installer. A reference card, which defines all

display codes, is included.

Label Inserts

Card File

6Addressable Intelligent Module—AIM-200 Addressable Intelligent Module

B501BJ Base

These intelligent, addressable detectors provide analog information to

the AIM-200. The AIM-200 processes this analog information and

continually makes decisions on the alarm, maintenance, or normal status

of each device. Each detector head mounts to a B501BJ base for ease of

installation or replacement. The sensitivity of each detector can be set

by the programmer at the AIM-200 for one of three levels (low,

medium, and high). Each detector responds to an address that is set in

the head via built-in rotary decimal switches.

2551J

An intelligent photoelectric smoke detector that provides analog

measurements of the optical smoke level in its chamber to the AIM-200

panel.

1551J

An intelligent ionization smoke detector that measures the level of

combustion products in its chamber using the ionization principle and

reports this measurement to the AIM-200.

5551J

An intelligent thermal sensor (135-degree F fixed temperature).

RA400Z

A remote single LED annunciator that can be wired directly off of an

addressable detector for annunciation of that detector’s alarm status.

Control and Monitor Modules

The M510CJ control module and the M500MJ monitor module provide

the interface between the FC-2000 and conventional initiating and

indicating devices. Both types of modules respond to an address that is

set by the installer with built-in rotary decimal switches. A flashing LED

indicates power is applied. A thermoplastic cover (illustrated at left) is

provided with each module for mounting to a 4-inch square mounting

box.

Optional

Peripherals

Intelligent

Detectors

Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 7

M500MJ

An addressable monitor module that can be used to monitor

conventional normally open contact alarm initiating devices, such as

manual pull stations, 4-wire smoke detectors, heat detectors, waterflow,

and supervisory devices. Supervised circuit can be wired NFPA Style B

or Style D.

M502MJ

An addressable monitor module that monitors conventional 2-wire

smoke detectors. Supervised circuits can be wired NFPA Style B or

Style D. M502MJ supervises initiating device circuit wiring,

communication loop, and input power.

M510CJ

An addressable control module that can be used as an indicating

appliance circuit for powering and supervising compatible, UL Listed

indicating appliances. Supervised circuits can be wired NFPA Style Y or

Style Z. By breaking two built-in tabs, the M510CJ can be employed as

a Form-C control relay.

M500XJ

The loop isolator module is an automatic switch that opens the circuit

voltage to a predetermined communications loop branch(es) whenever a

fault is detected on that circuit. The remainder of the communications

loop leading up to the M500XJ will continue to operate, unaffected by

the fault.

M501MJ

An addressable module that is functionally identical to an M500MJ

monitor module (Style B circuits only), but offered in a smaller package

for mounting directly in the electrical box of the device being monitored.

BGX-101L

The addressable manual pull station features a key-lock reset. The pull

station responds to an address set by the installer with built-in rotary

decimal switches. Includes key.

A2143-00

The 47K end-of-line resistor assembly is used in the supervision of

M500MJ Monitor and M510CJ Control Module circuits. It is included

with each M500MJ or M510CJ module.

8Addressable Intelligent Module—AIM-200 Addressable Intelligent Module

A77-716-02B

The end-of-line power supervision relay is used to supervise the power

to 4-wire smoke detectors and indicting appliances.

N-ELR

The N-ELR resistor assortment is required for use in Canada. It

provides a variety of resistor values to mount to a single ELR plate

(included). Resistors can be used for the supervision of an M500MJ

monitor module or M510CJ control module circuit.

Resistors included:

120 ohms, 470 ohms, 1.8K, 2.2K, 4.7K, 6.8K, 10K, 27K, and 47K.

Addressable Intelligent Module—AIM-200 Addressable Intelligent Module 9

Installing the AIM-200

This section outlines the installation procedure for the AIM-200. For

information on installing other FC-2000 equipment, refer to the Installing

the FC-2000Technical Bulletinin this manual.

Complete the following steps to install the AIM-200 onto the CHS-4

Chassis.

1. Mount the AIM-200 to a CHS-4 Chassis.

2. Insert the tab on the bottom of the AIM-200 into the slot on the

bottom of the CHS-4.

3. Fasten the AIM-200 to the top of the CHS-4 using the two captive

screws in the top corners of the module. Refer to Figure 4.

Note: If point annunciation (192 intelligent AIM-200 points and

56 standard system circuits) of a single AIM-200 is desired, the

AIM-200 must be mounted in the second slot of the first chassis

(directly to the right of the CPU). This annunciation option must

also be selected in system programming.

Installing the

AIM-200

10 Addressable Intelligent Module—AIM-200 Addressable Intelligent Module

Figure 4: Mounting the AIM-200

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Johnson Controls Système de contrôle

Johnson Controls

Johnson Controls HomeLink Manuel utilisateur

Johnson Controls

Johnson Controls MS2 Manuel

Johnson Controls

Johnson Controls SABROE Unisab III Control Manuel d'installation et d'exploitation

Johnson Controls

Johnson Controls Unisab III Manuel utilisateur

Johnson Controls

Johnson Controls System 450 Series Manuel de service

Johnson Controls

Johnson Controls Penn MR4 Manuel

Johnson Controls

Johnson Controls Unisab III Manuel utilisateur

Johnson Controls

Johnson Controls Penn System 450 Series Manuel de service

Johnson Controls

Johnson Controls CMS-1655 Manuel utilisateur

Johnson Controls

Johnson Controls FC-2000 Manuel de référence

Johnson Controls

Johnson Controls SABROE Unisab III Control Manuel d'installation et d'exploitation

Johnson Controls

Johnson Controls CCXL01 Manuel d'installation et d'exploitation

Johnson Controls

Johnson Controls ZZ Series Manuel utilisateur

Johnson Controls

Johnson Controls YORK YLAA0189SE Manuel utilisateur

Johnson Controls

Johnson Controls VMA1200 Series Manuel de service

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur