Johnson & Starley QuanTec 30C Manuel utilisateur

www.johnsonandstarley.co.uk

sustainable solutions under one roof

HEATING HOT WATER VENTILATION

USER’S INSTRUCTIONS

QUANTEC HR & COMBI

High Efficiency

Combination

Boilers

These instructions are to be left with the User

Publication No. ZZ 1431-3

January 2015

Quantec HR28C - G.C. No. 47-416-11

Quantec 30C - G.C. No. 47-416-12

Quantec 24C - G.C. No. 47-416-13

www.johnsonandstarley.co.uk

CONTENTS

1 General information 3

2 Boiler Control Panel 3

3 To light the boiler 4

4. Operating Functions 4

5 Reset the Boiler 5

6 Servicing & Maintenance 5

7 Escape of Gas 5

8 Cleaning 5

9 Trouble Shooting 6

NOTE

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

THESE INSTRUCTIONS SHOULD BE LEFT WITH THE USER

AFTER INSTALLATION

The Benchmark Scheme

Johnson & Starley Ltd is a licensed member of the Benchmark Scheme

which aims to improve the standards of installation and commissioning of domestic heating and hot water systems

in the UK and to encourage regular servicing to optimise safety, efficiency and performance.

Benchmark is managed and promoted by the Heating and Hotwater Industry Council. For more information visit

www.centralheating.co.uk

Please ensure that the installer has fully completed the Benchmark Checklist on the inside back pages of the

installation instructions supplied with the product and that you have signed it to say that you have received a full

and clear explanation of its operation. The installer is legally required to complete a commissioning checklist as a

means of complying with the appropriate Building Regulations (England and Wales).

All installations must be notified to Local Area Building Control either directly or through a Competent Persons

Scheme. A Building Regulations Compliance Certificate will then be issued to the customer who should, on receipt,

write the Notification Number on the Benchmark Checklist.

This product should be serviced regularly to optimise its safety, efficiency and performance. The service engineer

should complete the relevant Service Record on the Benchmark Checklist after each service.

The Benchmark Checklist will be required in the event of any warranty work and as supporting documentation

relating to home improvements in the optional documents section of the Home Improvements.

In the interest of continuous development Johnson and Starley reserve the right to change specification without prior notice.

Johnson and Starley prides itself on it’s ability to supply spare parts quickly and efficiently.

Sales/Spares & Replacement Help Line 01604 762881

K7 K1

K6 K2

K3 K5

Item Description

K1 CH - Central Heating +

K2 CH - Central Heating -

K3 Installer information

K4 Reset

K5 Summer/Winter mode

K6 DHW - Domestic Hot Water -

K7 DHW - Domestic Hot Water +

FIGURE 1. QUANTEC USER CONTROL PANEL

TIME

CONTROL

(optional)

DOMESTIC HOT

WATER

LED DISPLAY CENTRAL

HEATING

FUNCTION

MODES

RESET

BUTTON

INSTALLER

MODE

1. GENERAL INFORMATION

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: IT IS A STATUTORY REQUIREMENT THAT ALL GAS APPLIANCES BE INSTALLED BY

COMPETENT PERSONS, (i.e. GAS SAFE REGISTERED INSTALLERS. GAS SAFE MEMBERSHIP

ENQUIRIES - TEL: 0800 408 5500) IN ACCORDANCE WITH THE GAS SAFETY (INSTALLATION AND

USE) REGULATIONS (CURRENT EDITION). FAILURE TO COMPLY WITH THESE REGULATIONS MAY

RESULT IN PROSECUTION.

Part of the installation and commissioning of this appliance is related to instructions for use by the heating

engineer to the user where specific requirements may occur.

The QuanTec is a wall mounted, room sealed, condensing combination boiler, featuring full sequence

automatic spark ignition and fan assisted combustion. On the QuanTec HR a recuperator is fitted within the

boiler and preheats the incoming cold DHW for additional energy savings. Due to the high efficiency of the

boiler, condensate is produced from the flue gases and this is drained to a suitable disposal point through a

plastic waste pipe at the base of the boiler. A condensate ‘plume’ will also be visible at the flue terminal. The

QuanTec HR are combination boilers providing both central heating and instantaneous domestic hot water.

2. THE BOILER CONTROL PANEL

www.johnsonandstarley.co.uk

3. TO LIGHT THE BOILER

3.1 Switch the mains power ON and the boiler LED display will show “AP”. This puts the

boiler into the Air Purge Mode. See Figure 2.

3.2 Press the reset button “K4” twice. The boiler will go onto standby. This is the winter

mode.

SETTING THE DHW WATER TEMPERATURE

3.3 To set the hot water temperature press and hold “K7”, this will flash until the °C

temperature shows. By pressing the + and - buttons to set the desired temperature. The

temperature flashes 5 times to set the temperature and then goes back onto standby.

SETTING THE CH WATER TEMPERATURE

3.4 To set the central heating temperature press and hold “K1”, this will flash until the °C

temperature shows. By pressing the + or - buttons to set the desired temperature.

The temperature flashes 5 time to set the temperature and the display will go back to

standby.

4. OPERATING FUNCTIONS

4.1 OPERATING THE DOMESTIC HOT WATER

When the call for hot water is needed the boiler will fire. The display will show the full

flame, tap and the set water temperature. This will flash until the need for hot water is

satisfied. See Figure 4.

4.2 OPERATING THE CENTRAL HEATING

When the boiler fires in CH mode it fires for 1 minute, modulating the boiler. The display

will flash showing the radiator, the small flame and temperature. The flame symbol

increases with the demand for heat. Once temperature is reached the display will go

back to standby. See Figure 5.

Approximate flow temperatures for the boiler thermostat settings are:

4.3 DISPLAY CODES

In normal operation the boiler LED display will show codes:

1. Standby - no demand for heat.

2. CH being supplied.

3. DHW being supplied.

4. Boiler frost protection - boiler will fire if temperature is below 5°C.

5. During normal operation the burner on indicator will remain illuminated when the burner is lit.

Note: If the boiler fails to light after five attempts the fault code will be displayed.

4.4 TO SHUT DOWN THE BOILER

Set the mode to OFF by pressing K4.

To relight the boiler repeat the procedure detailed in ‘To light the boiler’.

4.5 FROST PROTECTION

If no system frost protection is provided and frost is likely during a short absence from home, leave the

heating controls (if fitted) at a reduced temperature setting. For longer periods, the entire system should be

drained.

If the system includes a frost thermostat then, during cold weather, the boiler should be turned OFF at the

time switch (if fitted) ONLY. The mains supply should be left switched ON, with the boiler thermostat left in

the normal running position.

TABLE. 2

Button Setting CH Flow Temperature

Minimum 40°C

Maximum

60°C

FIGURE 2

FIGURE 3

FIGURE 4

FIGURE 5

Sales/Spares & Replacement Help Line 01604 762881

4.6 LOSS OF SYSTEM WATER PRESSURE

The pressure gauge indicates the central heating system pressure. If the pressure is seen to fall below the

original installation pressure of 1-2 bar over a period of time then a water leak may be indicated. In this event

conduct the re-pressurising procedure. If unable to do so or if the pressure continues to drop a Gas Safe

Registered Engineer or in IE a Registered Gas Installer (RGII) should be consulted.

The boiler will not operate if the pressure has reduced to less than 0.3 Bar under this condition.

1. Ensure filling loop isolation valves are closed.

2. Remove the two caps

3. Attach on the filling loop.

4. Turn the filling loop isolation valves to the open position. The system will now fill.

5. Wait for pressure gauge dial to reach 1 to 1.5 bar.

6. Close the filling loop isolation valves.

7. Disconnect the filling loop at left hand side and angle upwards.

8. Attach the two blanking caps.

4.7 CONDENSATE DRAIN

The condensate drain must not be modified or blocked.

Blockage of the condensate drain, caused by debris or freezing, can cause automatic shutdown of the

boiler.

If freezing is suspected and the pipe run is accessible an attempt may be made to free the obstruction by

pouring hot water over the exposed pipe and clearing any blockage from the end of the pipe. If this fails to

remedy the problem the assistance of a Gas Safe Registered Engineer or in IE a Registered Gas Installer

(RGII) should be sought.

5. RESET THE BOILER

Press the reset button “K4” twice.

6. SERVICING & MAINTENANCE

It is recommended that a full maintenance check be carried out annually on the appliance. It is also

recommended to take out a further service agreement on the expiry of the guarantee period.

You can obtain further information on this from your gas supplier.

The appliance should be checked /serviced by a GAS SAFE registered installer.

If you require service on your appliance please contact your local installer or gas supplier.

On completion of the service the installer should fill in the service section at the rear of the BENCHMARK

Checklist. All installers registered with GAS SAFE carry an identification card. This card will have an ID

number which should be recorded in your logbook.

If you have any queries regarding your installer you can contact GAS SAFE

by telephone on 0800 408 5500.

The appliance should be serviced at least once a year by a Gas Safe

Registered Engineer or in IE a Registered Gas Installer (RGII).

7. ESCAPE OF GAS

Should a gas leak or fault be suspected contact the National Gas Emergency Service without delay.

Telephone 0800 111 999

Do NOT search for gas leaks with a naked flame.

8. CLEANING

For normal cleaning simply dust with a dry cloth.

To remove stubborn marks and stains, wipe with a damp cloth and finish off with a dry cloth.

DO NOT use abrasive cleaning materials.

www.johnsonandstarley.co.uk

ERROR CODES

E01

Ignition lockout

Check other gas appliances work

Reset boiler

Contact installer

E02

False flame lockout Contact installer

E03

Overheat lockout

Fill system to 1.0bar

Bleed radiators

Check radiator valves are open

Reset boiler

Contact installer

E05

Fan fault Contact installer

E08

Flame circuit failure Contact installer

E09

Valve feed back ERROR Contact installer

E12

EEPROM lockout Contact installer

E15

Sensor drift lockout

Fill system to 1.0bar

Bleed radiators

Check valves are open

Reset boiler

Contact installer

E16

E17

E18

Sensor stuck lockout

Fill system to 1.0bar

Bleed radiators

Check valves are open

Reset Boiler

Contact installer

E21

ADC lockout Contact installer

E33

Return thermistor fault Contact Installer

E34

Low power supply lockout Contact installer or Electrician

E35

Flow thermistor fault Contact Installer

9. TROUBLE SHOOTING

Sales/Spares & Replacement Help Line 01604 762881

FAULT CODES

F07

Exhaust sensor fault

Fill system to 1.0bar

Bleed radiators

Check radiator valves are open

Reset boiler

Contact installer

F13

Remote reset lockout

Turn power on and off

Press Reset

Contact installer

F37

Low water pressure

Fill system to 1.0bar

Bleed radiators

Check radiator valves are open

Reset boiler

Contact installer

F40

Water pressure too high

Check to see if the gauge is over 2.8bar

Bleed radiators

Reset boiler

Contact installer

F47

Water pressure sensor not connected Contact installer

F52

DHW sensor fault Contact installer

F53

Flue temperature sensor lockout Contact installer

GAS LEAKS

DO NOT OPERATE ANY ELECTRICAL SWITCHES, OR USE A NAKED FLAME

TURN OFF GAS SUPPLY

VENTILATE THE AREA BY OPENING THE DOORS AND WINDOWS

CALL THE NATIONAL GAS EMERGENCY SERVICES ON

TEL:

0800 111999

Johnson & Starley Ltd

Rhosili Road, Brackmills,

Northampton NN4 7LZ

sales@johnsonandstarley.co.uk

marketing@johnsonandstarley.co.uk

Reception

01604 762881

Fax

01604 767408

Johnson & Starley Dravo Division Industrial H&V

Sales

01604 707022

sales@johnsonandstarley.co.uk

www.dravo.co.uk

Anniversary 1922 - 2012

In the interest of continuous development Johnson & Starley reserve the right to change specifications without prior notice.

Autres manuels pour QuanTec 30C

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Johnson & Starley Chaudière

Johnson & Starley

Johnson & Starley RenoXtra 30CA Guide de l'utilisateur

Johnson & Starley

Johnson & Starley Quantec 24RK Manuel utilisateur

Johnson & Starley

Johnson & Starley HE16S Instructions de montage

Johnson & Starley

Johnson & Starley Quantec HR28CP ErP Manuel utilisateur

Johnson & Starley

Johnson & Starley Quantec HR28C ErP Guide de l'utilisateur

Johnson & Starley

Johnson & Starley Quantec 16RK Guide de l'utilisateur

Johnson & Starley

Johnson & Starley Quantec 24S Manuel utilisateur

Johnson & Starley

Johnson & Starley Reno HE30C Manuel utilisateur

Johnson & Starley

Johnson & Starley Reno HE16H Manuel utilisateur

Johnson & Starley

Johnson & Starley RenoXtra 30C Manuel utilisateur

Johnson & Starley

Johnson & Starley Reno HE30C Manuel utilisateur

Johnson & Starley

Johnson & Starley Reno HE16H Guide de l'utilisateur

Johnson & Starley

Johnson & Starley HE25S Manuel

Johnson & Starley

Johnson & Starley 47-416-14 Guide de l'utilisateur

Johnson & Starley

Johnson & Starley Reno HE30C Manuel

Johnson & Starley

Johnson & Starley QuanTec 30C Note de version

Johnson & Starley

Johnson & Starley HE16S Manuel utilisateur

Manuels Chaudière populaires d'autres marques

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Manuel utilisateur

Radijator

Radijator BIO max 23.1 Manuel utilisateur

Brunner

Brunner BSV 20 Manuel utilisateur

Buderus

Buderus Logamax GB062-24 KDE H V2 Manuel utilisateur

Potterton

Potterton 50e Fiche technique

UTICA BOILERS

UTICA BOILERS TriFire Manuel utilisateur

Joannes

Joannes LADY Series Manuel

ECR International

ECR International UB90-125 Manuel d'instructions

Froling

Froling FHG Turbo 3000 Manuel utilisateur

Froling

Froling P4 Pellet 8 - 105 Manuel utilisateur

U.S. Boiler Company

U.S. Boiler Company K2 Manuel utilisateur

Henrad

Henrad C95 FF Manuel utilisateur

NeOvo

NeOvo EcoNox EF 36 Manuel utilisateur

Potterton

Potterton PROMAX SL 12 Manuel utilisateur

Eco Hometec

Eco Hometec EC 25 COMPACT Manuel utilisateur

Viessmann

Viessmann VITODENS 200 Mode d’emploi

Baxi

Baxi Prime 1.24 Manuel utilisateur

REXNOVA

REXNOVA ISA 20 BITHERMAL Manuel utilisateur