Jbc DIT-D Manuel utilisateur

Premium Soldering station

Ref. DIT-D

www.jbctools.com

Manual ..............................1 unit

Ref. 0020509

Packing List

The following items should be included:

DI Control Unit ...............1 unit

Ref. DI-1D (120V)

DI-2D (230V)

DI-9D (100V)

Stand ................................1 unit

Ref. AD-SD

General Purpose

Handle ........................... 1 unit

Ref. T245-A

Premium soldering station

Ref. DIT-D

Power Cord .....................1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

Stand cable ................... 1 unit

R ef. 0 0112 83

ESD

Tip Cleaner ......1 unit

Ref. CL8499

Sponge ............ 1 unit

Ref. S0354

Cartridge ........ 1 unit

Ref. C245903

Check our website for the corresponding manuals. Also available in other languages.

Brass wool ..... 1 unit

Ref. CL6210

www.jbctools.com

Features & Connections

Power Socket

DI Control Unit

Stand

Ref. AD-SD

Stand cable

Ref. 0 0 1128 3

Equipotential connector

Desoldering

Pump connector

USB Connector

Main switch

Fuse

General Purpose

Handle

Ref. T245-A

Compatibility

* The MN-A Nitrogen Flow Regulator is required.

Select the equipment that best suit your soldering or desoldering needs.

Basic working system Peripherals

Control

Unit Stand Tool Cartridge

Range

MS-A

MV-A MN-A FS500-1A

FS500-2A P-005

DI-D

AD-SD

T210-A C210

T245-A C245

T470 -A C245

DN-SE

T210-NA* C210

T245-NA*

C245

T470 -NA*

AP-SD AP250-A C250

PA-SD PA120-A C120

HT-SD HT420-A C420

DS-SD DS360-A C360

DR-SD DR560-A C560

www.jbctools.com

Maintenance

Fuse

- Replace any defective or damaged pieces. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

Before carrying out maintenance or storage, always allow the equipment to cool and unplug the

stand from the station and the tool.

- Clean the station screen with a glass cleaner

or a damp cloth.

- Use a damp cloth to clean the casing, the

stand and the tool. Alcohol can only be

used for cleaning the metal parts.

- Periodically check that the metal parts of the

tool and stand are clean so that the station

can detect the tool status.

- Maintain tip surface clean and tinned prior to

storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat

transfer to the solder joint.

- Periodically check all cables, tubes and filters

to ensure proper solder suction.

- Replace a blown fuse as follows:

1. Pull off the fuse holder and remove the

fuse. If necessary use a tool to lever it off.

2. Press the new fuse into the fuse holder

and replace it in the station.

Clean

perodically

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts. Antistatic handle of soldering irons is electrically conductive.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station

is turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- It is necessary to turn the station off before changing tips.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Avoid the contact of flux with skin or eyes to prevent irritation

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Safety

www.jbctools.com

产品中有害物质的名称及含量

有害物质含量表

部件名称

有害物质

铅(Pb) 汞(Hg) 镉(Cd) 六价铬

(Cr(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

烙铁头 O O O O O O

手柄 O O O O O O

电源线 O O O O O O

主机 O O O O O O

电源插座 O O O O O O

保险丝 O O O O O O

主开关 O O O O O O

电位连接 X O O O O O

变压器 O O O O O O

线路板 X O O O O O

O 表示该有害物质在该部件所有均质材料中的含量均在GB/T 26572 规定的限量要求以下。

X 表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定的限量要求。

Specifications

Premium Soldering station

DIT-1D / DIT-2D / DIT-9D

- Total weight: 4,250 kg (9.36 lb)

DI-1D 120V 50/60Hz. Input fuse: 2A. Output: 23.5V.

DI-2D 230V 50/60Hz. Input fuse: 1A. Output: 23.5V.

DI-9D 100V 50/60Hz. Input fuse: 2.5A. Output: 23.5V.

- Weight: 2,15 3 kg (4.74 lb)

- Size: 90 x 105 x 180 mm (3.5 x 4.1 x 7.1 in)

- Output Peak Power: 130W

- Temperature Range : 90 to 450 °C (190 to 840 °F)

- Idle Temp. Stability (still air): ±1.5 ºC / ±3 ºF

- Tip to ground resistance: <2 ohms

- Tip to ground voltage: <2mV RMS

- Ambient operating temp: 10 to 40 ºC (50 to 104 ºF)

- Connections USB-B / Peripherals connectors

Complies with CE standards.

ESD protected.

www.jbctools.com

Exploded View

Autres manuels pour DIT-D

Table des matières

Manuels pistolet à souder populaires d'autres marques

Bakon

Bakon 3200 Manuel utilisateur

Proxxon

Proxxon Gaslotset MGS Manuel utilisateur

HAKO

HAKO FX-8804 Manuel utilisateur

SATA

SATA 02002A Manuel utilisateur

Velleman

Velleman HRJA151 Manuel utilisateur

Weller

Weller WSM 1 Manuel utilisateur

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instructions de montage

ersa

ersa i-CON 1V Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-100 Manuel utilisateur

Weller

Weller WAD 101 Manuel utilisateur

Weller

Weller WXD 2 Manuel utilisateur

AlienTek

AlienTek T100 Manuel utilisateur

Atten

Atten ATETOOL AT-689A Manuel utilisateur

Surtek

Surtek 112554 Dimensions et guide d'installation

Parkside

Parkside PLBS 30 A1 Manuel utilisateur

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

multicomp pro

multicomp pro MP740893 Manuel utilisateur

jbc DIT-D Manuel utilisateur

Manuels pistolet à souder populaires d'autres marques