Jbc CP-D Manuel utilisateur

www.jbctools.com

Español 15

English 3

Page

Compact

Micro Tweezers Station

Ref. CP-D

www.jbctools.com

2 3

Manual .......................................................... 1 unit

Ref. 0009417 (100V/120V)

Packing List

The following items should be included:

CP Control Unit ........................................ 1 unit

Ref. CP-1D (120V)

CP-2D (230V)

CP-9D (100V)

Brass Wool .................... 1 unit

Ref. CL6210

ww w.j bc too ls.c om

Sponge ............................ 1 unit

Ref. S0354

Micro Tweezers ........................................ 1 unit

Ref. PA120-A

Cartrdiges .............. 2 units

Ref. C120002

Compact

Micro Tweezers Station

Ref. CD-SD

Power Cable ............................................... 1 unit

Ref. 0009417 (100V/120V)

0009401 (230V)

www.jbctools.com

4 5

Power Socket

Main switch

Fuse

Cable Collector

Tip Cleaning System

Process Control

Adjustable Stand:

Intelligent Heat

Management

Equipotential connection

USB-B connector

Features

Micro

Tweezers

Ref. PA120-A

Adjustable stand

Cable collector

Adjust the tool stand to suit your work position.

Place the cable on the collector to keep the work area free of cable.

www.jbctools.com

6 7

Wiping:

Use the slots to wipe off any remaining

particles.

Tip Cleaning System

Tapping:

Tap gently to eliminate excess solder.

Sponge

Ref. S0354

The least harmful cleaning method.

Keep the sponge damp with distilled water to prevent

tip wear.

Brass Wool

Ref. CL6210

Very effective cleaning method.

Leaves a small layer of solder on the tip preventing

oxidation between cleaning and rewetting.

Select the option that best suits your tip cleaning needs.

More options for the splashguard (not supplied):

Inox Wool

Ref. CL6205

An alternative to

Brass Wool.

Metal Brush

Ref. CL6220

When used carefully,

it provides a more

thorough cleaning.

Splashguard

Tip Wipe

Changing cartridge

Compatible cartridges

CP station works with C120 cartridge range. Check the model that best adapts to your soldering needs

in www.jbctools.com

Turn the station off and follow these guidelines for a safe cartridge change:

Important: Insert the cartridge to the mark

for a proper connection.

Mark

1. Removing 2. Inserting

Loosen the screw to remove the cartridge.

Use a flat nosed pliers if the cartridge is hot.

ø0,7 1,5mm

ø 0,2

5mm

6m m

C120-009 C120-01

C120-004 C120-001C120-005 C120-009

C120-010

3. Aligning

Use a flat nosed pliers for a correct alignment.

Alignment

Important: Tighten the screw. This is

necessary for the tool to function.

Be careful not to over-tighten the screw.

4. Fixing

JBC

Manager

JBC

Updater

www.jbctools.com

· Change temperature

(from 90 to 450ºC)

Tool Settings:

· Select temperature levels

· Fix one temperature

Tool Settings:

· Set Sleep temperature

· Set Sleep delay

(from 0 to 9 min or no Sleep)

Tool Settings:

· Set Hibernation delay

(from 0 to 35 min or no

hibernation)

8 9

USB Connector

Download the latest software from our website to improve your soldering station.

JBC Updater

www.jbctools.com/software.html

Update the station software via USB connection:

JBC Manager

www.jbctools.com/manager.html

Manage and monitor as many stations as your PC can handle by using the JBC Manager. You can

export data to another PC.

Cable USB AB

Create graphs of the

soldering process in real time

with power and temperature

data.

Manager Settings

Change settings for a group

of JBC stations at the same

time.

any JBC

station

USB

Hub

Cable

USB AB

Operation

The JBC Exclusive Heating System

Our revolutionary technology is able to recover tip temperature extremely quickly. It means the user

can work at a lower temperature and improve the quality of soldering. Tip temperature is further

reduced thanks to the Sleep and Hibernation modes which increase tip life by 5.

1. Work

When the tool is lifted from the

stand the tip will heat up to the

selected temperature.

2. Sleep

When the tool is in the stand,

the temperature falls to

180ºC / 360ºF (preset sleep

temperature).

Tool in the stand

Actual Temp. 180

Sleep

Tool in the stand after sleep

No heat

Actual Temp. 20

Hibernation

Selected temp.

350

Power 10%

350

Long time

in the

stand

3. Hibernation

After longer periods in the stand

(pre-set to 30 minutes), the

power is cut and the tool

cools down to room temperature.

www.jbctools.com

10 11

Menu Screen

Main menu

Counters

Tool settings

4 Counters

Program version

Hibernation hours 0

No tool hours 0

6 Sleep cycles

Sleep temp 180

Hibernationdelay

0 min

Temp adjust + O

Tool 245

BackBack

Station settings

Back

Pre-set PIN: 0105

This screen displays

information of tool status

in real time.

Selected temp.

350

Power 10%

Fixed temp.

350

Shown when you fix a

specific temp.

Shown when you have

selected temp. levels.

Work Screen

Process Control

Fix one temp -----

Temp levels set OFF

Sleep delay 0 min

5 Beep ON

Change PIN

1 Temp unit

Celsius

Maximum temp 400

Minimum temp 200

Help text OFF

Levels ºC

270 350 400

Plugged hours 0

Working hours 0

Sleep hours 0

350

Exit

1 Reset settings

Station settings

Tool settings

Before carrying out maintenance or storage, always allow the equipment to cool.

- Clean the station screen with a glass cleaner

or a damp cloth.

Remove the fuse by pulling the black cap.

If necessary use a tool to lever it off.

Press the new fuse into the holder and

replace it in the station.

Clean

periodically

- Use a damp cloth to clean the casing and

the tool. Alcohol can also be used to clean

the metal parts.

- Periodically check that the metal parts of

the tool and stand are clean so that the

station can detect the tool status.

- Maintain tip surface clean and tinned prior

to storage in order to avoid tip oxidation.

Rusty and dirty surfaces reduce heat

transfer to the solder joint.

- Periodically check all cable connections.

Maintenance

- Replace a blown fuse as follows:

- Replace any defective or damaged parts. Use original JBC spare parts only.

- Repairs should only be performed by a JBC authorized technical service.

CP-1D 120V 50/60Hz. Input fuse: 2A. Output: 23.5V.

CP-2D 230V 50/60Hz. Input fuse: 1A. Output: 23.5V.

CP-9D 100V 50/60Hz. Input fuse: 2A. Output: 23.5V.

- Weight: 2.7 Kg (6 lb)

- Dimensions: 150 x 175 x 145 mm

- Temperature range: 90 to 450°C / 190 to 840°F (±5%).

- Output Peak Power: 80W.

- Tip to ground resistance <2 ohms

- Tip to ground voltage <2mV RMS

- Ambient operating temp: 10-40 ºC / 50-104 ºF

- USB connection station-PC

Complies with CE standards

ESD protected housing “skin effect”

www.jbctools.com

12 13

It is imperative to follow safety guidelines to prevent electric

shock, injury, fire or explosion.

- Do not use the units for any purpose other than soldering or rework. Incorrect use may cause

fire.

- The power cord must be plugged into approved bases. Be sure that it is properly grounded

before use. When unplugging it, hold the plug, not the wire.

- Do not work on electrically live parts.

- The tool should be placed in the stand when not in use in order to activate the sleep mode.

The soldering tip, the metal part of the tool and the stand may still be hot even when the station is

turned off. Handle with care, including when adjusting the stand position.

- Do not leave the appliance unattended when it is on.

- Do not cover the ventilation grills. Heat can cause inflamable products to ignite.

- Use a “non residue” classified flux and avoid contact with skin or eyes to prevent irritation.

- Be careful with the fumes produced when soldering.

- Keep your workplace clean and tidy. Wear appropriate protective glasses and gloves when

working to avoid personal harm.

- Utmost care must be taken with liquid tin waste which can cause burns.

- This appliance can be used by children over the age of eight and also persons with reduced

physical, sensory or mental capabilities or lack of experience provided that they have been given

adequate supervision or instruction concerning use of the appliance and understand the hazards

involved. Children must not play with the appliance.

- Maintenance must not be carried out by children unless supervised.

Safety Specifications

www.jbctools.com

14 15

Composición

Los siguientes artículos deberían estar incluidos:

Manual .................................................... 1 unidad

Ref. 0014627

CP Control Unit

Unidad de Control CP ........................ 1 unidad

Ref. CP-1D (120V)

CP-2D (230V)

CP-9D (100V)

Brass Wool

Lana de latón ............ 1 unidad

Ref. CL6210

ww w.j bc too ls.c om

Sponge

Esponja ...................... 1 unidad

Ref. S0354

Micro Tweezers

Micro pinzas .......................................... 1 unidad

Ref. PA120-A

Cartrdiges

Cartuchos ............. 2 unidades

Ref. C120002

Compact

Micro Tweezers Station

Ref. CD-SD

Power Cable

Cable de red .......................................... 1 unidad

Ref. 0009417 (100V/120V)

0009401 (230V)

www.jbctools.com

16 17

Toma de corriente

Interruptor de red

Fusible

Conexión equipotencial

Conector USB-B

Características

Micro

Tweezers

Micro pinzas

Ref. PA120-A

Soporte Ajustable

Recogecable

Ajuste el soporte de la herramienta para adaptarlo a su posición de trabajo.

Coloque el cable en el recogedor y ajuste su posición para evitar molestias en la zona de trabajo.

Soporte ajustable:

Gestión inteligente

del calor

Control del

proceso

Recogecable

Sistema de limpieza

de puntas

ø0,7 1,5mm

ø 0,2

5mm

6m m

C120-009 C120-01

C120-004 C120-001C120-005 C120-009

C120-010

www.jbctools.com

18 19

Limpiar:

Utilice las ranuras para eliminar posibles

partículas adheridas a las puntas.

Sistema de limpieza de puntas

Golpetear:

Golpee ligeramente los cartuchos para

eliminar el exceso de estaño.

Sponge

Esponja

Ref. S0354

El método más suave y menos dañino. Mantenga la

esponja húmeda (no mojada) con agua detilada para

evitar el deterioro de la punta.

Brass Wool

Lana de latón

Ref. CL6210

El método más efectivo. La lana de latón deja una fina

capa de estaño en la punta que previene la oxidación

entre la limpieza y la rehumectación.

Elija la opción que se ajuste mejor a sus necesidades de limpieza.

More options for the splashguard (not supplied):

Inox Wool

Lana inoxidable

Ref. CL6205

Un método alternativo

a la lana de latón.

Metal Brush

Cepillos de metal

Ref. CL6220

Si se utiliza con prudencia,

proporciona una limpieza

más profunda.

Protector antisalpicaduras

Limpiador de puntas

Cambio de cartucho

Cartuchos compatibles

La estación CP funciona con la gama de cartuchos C120. Encuentre el modelo que se ajuste mejor a

sus necesidades de soldadura en www.jbctools.com

Desenchufe la estación o la herramienta y siga estas instrucciones para un cambio seguro:

Importante: Inserte el cartucho hasta la

marca para una correcta conexión.

Marca

1. Retirar 2. Insertar

Afloje el tornillo y retire el cartucho.

Utilice alicates de punta plana si el

cartucho está caliente.

3. Alinear

Utilice alicates de punta plana para alinear

las puntas de forma segura.

Alineamiento

Atornille de nuevo. Es necesario para que la

herramienta funcione.

No apriete en exceso el tornillo.

4. Fijar

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels jbc pistolet à souder

Manuels pistolet à souder populaires d'autres marques

Bakon

Bakon 3200 Manuel utilisateur

Proxxon

Proxxon Gaslotset MGS Manuel utilisateur

HAKO

HAKO FX-8804 Manuel utilisateur

SATA

SATA 02002A Manuel utilisateur

Velleman

Velleman HRJA151 Manuel utilisateur

Weller

Weller WSM 1 Manuel utilisateur

Vishay Precision Group

Vishay Precision Group Micro-Measurements Mark V Instructions de montage

ersa

ersa i-CON 1V Manuel utilisateur

Hakko Electronics

Hakko Electronics FX-100 Manuel utilisateur

Weller

Weller WAD 101 Manuel utilisateur

Weller

Weller WXD 2 Manuel utilisateur

AlienTek

AlienTek T100 Manuel utilisateur

Atten

Atten ATETOOL AT-689A Manuel utilisateur

Surtek

Surtek 112554 Dimensions et guide d'installation

Parkside

Parkside PLBS 30 A1 Manuel utilisateur

BlackJack SolderWerks

BlackJack SolderWerks BK8000 Manuel utilisateur

Weller

Weller WX1 Manuel utilisateur

multicomp pro

multicomp pro MP740893 Manuel utilisateur

jbc CP-D Manuel utilisateur

Manuels pistolet à souder populaires d'autres marques