jbc PHSE-KA Manuel utilisateur
IR Preheater Set
Ref. PHSE-KA
INSTRUCTION MANUAL
www.jbctools.com
2
Packing List
The following items should be included:
Power Cord ............................................... 1 unit
Ref. 0009417 (100V/120V)
0009401 (230V)
Thermocouple .............. 1 unit
Ref. PH218
Kapton Tape .................. 1 unit
Ref. PH217
Manual ............................ 1 unit
Ref. 0021330
Ref. PHSE-KA
IR Preheater Set
IR Preheater Support ............................. 1 unit
Ref. PHS-SA
Heater Unit
Console
IR Preheater .............................................. 1 unit
Ref. PHSE-1A (120V)
PHSE-2A (230V)
PHSE-9A (100V)
RJ45 Cable ................................................ 1 unit
Ref. 0019914
www.jbctools.com
3
Features
Pedal socket (optional)
Ref. P-005
Heating Areas
Power socket
Power
Fixing brackets for
PHS-SA IR
Preheater Support
Heater Unit
Console
2,8” Color
TFT screen
Start / Stop
USB-B connector
Zone B
Zone A
RJ45 connector
to Heater Unit
USB-A connector
Foot for vertical set up
Push the button
to fold the foot
USB-B connector
RJ45 connector
to Console
RJ12 connector
to Robot
Thermocouple
connectors
www.jbctools.com
4
28mm
50mm
70mm
Remove these knobs for
the low level if necessary
It allows adjustment for 3 heights between the PCB and the Heating Area of the PHSE-A Heater
Unit.
Low level
High level
Medium level
PHS-SA Features
Clamp knobs
Sliding guide
Spring guide
Allen key
Height Adjustment
For fixing irregular
shaped PCBs to
the support.
For fixing identical
PCBs in the same
position.
Slot clamps
5
After loosening the SP guide knobs, push the
PCB against the SP guide and lift out.
Place large PCBs on
the 4 rubber caps
Push the PCB against the SP guide, position it
and tighten the SP guide knobs.
Changing PCBs of the same batch
The support lets you place PCBs of the same batch so as to always heat the same area.
Use the sliding guides to change the PCBs.
Removing the PCB Placing another PCB
Reworking large PCBs
www.jbctools.com
6
USB flash drive is connected.
Station is controlled by a PC.
Station is controlled by a robot.
Station software update.
Press INFO to start the process.
Warning.
Press INFO for failure description.
Error. Press INFO for failure description,
the type of error and how to proceed.
System notifications (Status Bar)
Menu Options
Station
Information
Instant power
supplied to
heater
Status
indicator
Temperature mode
Status bar
*Original PIN: 0105
Thermocouple
selected temp.
and mode
· Control
· Protection
· Info
General Work mode Profile editor
ResetGraphics Files
Press INFO for each parameter description.
Available languages: English, Spanish,
German, French, Italian, Portuguese,
Japanese, Chinese, Russian and Korean.
Thermocouple
current temp.
Select Temp. mode from the Work mode menu. In this mode the heater unit maintains the selected
temperature for the TC1 thermocouple as long as the other TCs do not reach the control/protection
temperature limit.
TC1 current
and selected
Temperature
14:15
20ºC
Power
45%
TC1
45ºC
Selected 150ºC
TC2
P100ºC
20ºC
TC3
P100ºC
20ºC
TC4
P100ºC
C
P
7
Instant power
supplied to
heater
Status
indicator
Selected
Power
Power mode
Status bar
Select Power mode from the Work mode menu. In this mode the heater unit maintains the selected
power as long as the thermocouples do not reach the control/protection temperature limit.
Thermocouple
current temp.
Thermocouple
selected temp.
and mode
· Control
· Protection
· Info
Thermocouples
Select Thermocouples from the Work mode menu to set them up.
The thermocouples (TC) can work in three diferent ways depending on what is needed.
· Control: the unit mantains the selected temperature.
· Protection: the Heater Unit stops if the TC reaches the selected temperature.
· Info: the TC temperature is shown in the work screen.
The TC1 is always working in Control mode for the Temperature mode as well as for Profiles mode.
The temperature of each TC can also be selected from the work screen.
14:15
20ºC
Power
45%
Selected power
45%
TC1
P100ºC
20ºC
TC3
P100ºC
20ºC
TC4
P100ºC
20ºC
TC2
P100ºC
C
P
www.jbctools.com
8
For repetitive jobs we recommend running profiles without the Thermocouple (TC). In order to do
so, the Teach profile mode has to be executed before running any profile. It can be executed from
the Work mode menu if the Profiles mode is selected. Once the profile has been run to the end, the
system has all the process data which you can save.
Once it is saved, you can run this profile without connecting the Thermocouple (TC). The heating
process will be the same as long as the same working conditions are respected.
The profiles which already have the data from the Teach profile are marked with this symbol
These profiles can be run either with or without the Thermocouples. It can be chosen from the
Profiles mode work screen:
Teach profile
Select Profile mode from the Work mode menu. In this mode the heater unit regulates the
temperature of the TC1 thermocouple according to the selected profile as long as the other TCs do
not reach the control/protection temperature limit.
Profiles mode
14:15
20ºC
TC1
Stop
20ºC
TC2
PROFILE1
200
100
20ºC
TC3
20ºC
TC4
9
· Add point
· Delete point
· Load profile
· Save profile
· Exit
Data for
these points
Profile name
Profile editor
The Profile editor can be opened from the main menu or from the Profiles mode work
screen by pressing the ‘OK’ button.
In this mode you can edit as many as 25 profiles of temperature.
Menu
Options
Profile
editor
JBC set profiles
There are 3 profiles predefined by JBC: A, B and C. The difference between them is the number of
steps: 2, 3 or 4. The thicker your PCB is and the more layers it contains, the more steps are needed
to obtain a gradual warming.
These profiles are not modifiable but can be used as a template to create your own profiles.
JBC-A
2 steps
JBC-B
3 steps
JBC-C
4 steps
PCB reference
specifications:
FR4 1,6mm thick
and 2 layers.
FR4 2,2mm thick
and 6 layers.
FR4 1,6mm thick
and 6 layers.
Profiles set using the low position of the PHS-SA Support (28 mm in height between the PCB and the heating area).
14:15
5m 00s
150ºC
PROFILE1
200
100
0 60 120 180 240 300
Point
2/4
Temp Time
2m 00s
www.jbctools.com
10
Process analysis
By pressing Graphics in the main MENU, temperature of TC1 thermocouple and power
figures in real time are displayed.
17:14
Temperature
Power (%)
Ext.Temp[ºC]
50
100
150
200
250
300
Power[%]
Graphics
Switch Y axis
between power
and temperature
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels jbc Système de chauffage
