JB Systems LED Marvel Manuel utilisateur

ENGLISH USER MANUAL

JB SYSTEMS®1/44 LED MARVEL

OPERATION MANUAL

Thank you for buying this JB Systems®product. To take full advantage of all possibilities and for your own

safety, please read these operating instructions very carefully before you start using this unit.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the current European and

national guidelines. Conformity has been established and the relevant statements and documents have been

deposited by the manufacturer.

This device was designed to produce decorative effect lighting and is used in light show systems.

Thanks to its very nice and elegant design this LED projector fits in any interior (living room, bedroom, bar,

lounge, restaurant, …)

On top of that it’s also perfect example of multi-functionality:

Can be used as sound activated “party light”(internal programs & chases)

The perfect “atmosphere” creator (slowly changing color fades)

Small but effective wall washer (color your walls!)

Several units can be controlled by a DMX-controller for synchronized operation.

It contains 6 individually controllable LED-panels for a maximum variety and impact of the effects.

A total of 216 leds (72 red + 72green + 72blue) guarantee excellent light output and good color mixing.

Static or sound activated programs (internal mic) with different modes

One unit can be used in standalone or several units can be connected together in master/slave to obtain

wonderful synchronized effects!

IR-remote control included

DMX-control possible: 21channels for full RGB control + chase presets with adjustable speed.

Multifunctional base:

Just put it on a table or horizontal surface

Fix it against a wall and point the unit in any direction

Power input: 12Vdc, separate low voltage adapter included

BEFORE USE

Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not use the device and consult your dealer first.

Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

or problems caused by disregarding this user manual.

Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check the contents:

Check that the carton contains the following items:

Operating instructions

LED MARVEL

Mounting tripod

External 12Vdc power supply

Infrared (IR) remote control

ENGLISH USER MANUAL

JB SYSTEMS®2/44 LED MARVEL

SAFETY INSTRUCTIONS:

To protect the environment, please try to recycle the packing material as much as possible.

To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

This unit is for indoor use only.

Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids.

Don’t cover any ventilation openings as this may result in overheating.

Prevent use in dusty environments and clean the unit regularly.

Keep the unit away from children.

Inexperienced persons should not operate this device.

Maximum safe ambient temperature is 35°C. Don’t use this unit at higher ambient temperatures.

Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

Always unplug the unit when it is not used for a longer time or before to start servicing.

Check that the available voltage is not higher than the one stated on the unit.

The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

Never let the power-cord come into contact with other cables!

In order to avoid a hazard, the unit shall only be used with the AC-adaptor delivered with it. If the AC-

adaptor is damaged, a same model adaptor shall be used only.

Don’t connect the unit to any dimmer pack.

Always use an appropriate and certified safety cable when installing the unit.

In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.

In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

The housing and the lenses must be replaced if they are visibly damaged.

Please use the original packing when the device is to be transported.

Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

Important: Never look directly into the light source! Don’t use the effect in the presence of persons suffering

from epilepsy.

CAUTION: To reduce the risk of electric shock, do not remove

the top cover. No user-serviceable parts inside. Refer servicing

to qualified service personnel only.

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the

use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence

of important operation and maintenance (servicing) instructions in the literature accompanying

this appliance.

This symbol means: indoor use only

This symbol means: Read instructions

This symbol means: Safety Class II appliance

This symbol determines: the minimum distance from lighted objects. The minimum distance

between light-output and the illuminated surface must be more than x meters

The device is not suitable for direct mounting on normally flammable surfaces. (suitable only for

mounting on non-combustible surfaces)

CAUTION: Do not stare at operating lamp.

May be harmful to the eyes.

ENGLISH USER MANUAL

JB SYSTEMS®3/44 LED MARVEL

DESCRIPTION + OPERATION:

1. LEVEL (DIMMER) button

2. MODE button

3. PT/COL button

4. SPEED button

5. S2L (Sound to Light) led

6. ON/OFF indicator

7. Base

8. DMX in/out connectors

9. Power adapter in/out

10. Microphone

Upon the user’s choice, the

unit can work in stand-alone

automatic modes, or with

fixed colors, or it may be

controlled by the included IR

remote control or external

DMX-controllers.

This chapter refers to

standalone operation and

operation with the IR remote

control. Please see chapter “Synchronization and DMX control” for digital remote

control. For standalone operation, make sure that NO CABLE is plugged into the rear

“DMX IN” socket.

The user interface elements provide the following functions:

1. LEVEL button

By consecutively pressing this key on the main units itself, it allows the sequential

choice of 4 different brightness levels: 0%(off)/25/50/75/100%. The same levels are

available by means of the remote control; however the LEVEL up/down keys on the

remote control only allow to choose the 25/50/75/100% levels, while the blackout

function (0%) is directly available via the remote controls on/off key.

2. MODE button

By consecutively pressing this key on the main units itself, it allows the sequential choice of 5 different

operating modes:

CHASE: different chase patterns that can be selected with the PT/COL button –more details below.

FADE: fading between the 6 panels, different patterns can be selected with the PT/COL button –

more details below.

MOOD: all 6 panels fade from one color to another, different color cycles can be selected with the

PT/COL button –more details below.

SCENE: all 6 panels show the same color, 12 different colors can be selected with the PT/COL

button –more details below.

FLASH (STROBE): different patterns in white RGB each can be selected with the PT/COL button –

more details below.

Note: when using the IR remote, the 5 modes can be chosen directly by designated keys.

3. PT/COL button

This key changes –depending on the chosen MODE –either the color, or the pattern + color. The

choices in accordance to the chosen mode are:

In CHASE Mode: 5 pattern presets with switching transition in two color combinations each can be

chosen by consecutively pressing the PT/COL key on the unit itself or the PT/COL up/down keys on the

remote control:

Preset

Colour 1

Color 2

Color 3

Pattern

Red

Blue

Green

3C-16-Zip-updown

ENGLISH USER MANUAL

JB SYSTEMS®4/44 LED MARVEL

Pink

Turquoise

Lime

3C-16-Zip-updown

Red

Green

Blue

3C-22-Crossing

Pink

Turquoise

Lime

3C-22-Crossing

Red

Green

Blue

3C-22-ContractExpand

Pink

Turquoise

Lime

3C-22-ContractExpand

Red

Green

Blue

3C-22-PingPong

Pink

Turquoise

Lime

3C-22-PingPong

Red

Green

Blue

3C-33-Fork

Pink

Turquoise

Lime

3C-33-Fork

Sequence

Patterns 1/3/5/7/9/2/4/6/8/10

In FADE Mode: 5 pattern presets with fading transition in two color combinations each can be chosen by

consecutively pressing the PT/COL key on the unit itself or the PT/COL up/down keys on the remote

control:

Preset

Colour 1

Color 2

Color 3

Pattern

Red

Blue

Green

3C-16-Zip-updown

Pink

Turquoise

Lime

3C-16-Zip-updown

Red

Green

Blue

3C-22-Crossing

Pink

Turquoise

Lime

3C-22-Crossing

Red

Green

Blue

3C-22-ContractExpand

Pink

Turquoise

Lime

3C-22-ContractExpand

Red

Green

Blue

3C-22-PingPong

Pink

Turquoise

Lime

3C-22-PingPong

Red

Green

Blue

3C-33-Fork

Pink

Turquoise

Lime

3C-33-Fork

Sequence

Patterns 1/3/5/7/9/2/4/6/8/10

In MOOD Mode: 10 color cycle presets can be chosen by consecutively pressing the PT/COL key on the

unit itself or the PT/COL up/down keys on the remote control:

Preset

Colour 1

Color 2

Color 3

Pattern

Red

Blue

2C_6Change

Pink

Lime

2C_6Change

Green

Red

2C_6Change

Lime

Turquoise

2C_6Change

Blue

Green

2C_6Change

Pink

Turquoise

2C_6Change

Red

Blue

Green

3C_6Change

Red

Green

Blue

3C_6Change

Red

Blue

Green

2C_Burst

Pink

Turquoise

Lime

2C_Burst

Random

Random Roll

Note: Other than in CHASE and FADE mode, in MOOD mode, all 6 segments are active, and show the

same color in the first 8 presets (mixed color presets 9/10/11).

In SCENE Mode: 12 color presets can be chosen by consecutively pressing the PT/COL key on the unit

itself or the PT/COL up/down keys on the remote control:

Preset

Colour

Red

Green

Blue

Yellow*

Pink*

Turquoise*

Lime

Orange

Marine

Frog

Lavender

ENGLISH USER MANUAL

JB SYSTEMS®5/44 LED MARVEL

Candy

White (50% Level)

Note: there is no “color off” status in SCENE mode.

In FLASH (STROBE) Mode: 5 strobe pattern presets can be chosen by consecutively pressing the

PT/COL key on the unit itself or the PT/COL up/down keys on the remote control:

Preset

Preset Name

Description

Strobe-All6-

RGB-SEQ

All 6 Segments strobe alternating with a 4-Flash cycle in red,

green, blue with 16 Hz

Strobe-All6-

PTL-SEQ

All 6 Segments strobe alternating with a 4-Flash cycle in

pink, turquoise, lime with 16 Hz

Strobe-222-

RGB-SEQ

Segments 1+4 / 2+5 / 3+6 flash sequentially while in every

step the currently active segments keep strobing for 4

Flashes before the the next segments take over. The flash

color cycles through R/G/B

Strobe-222-PTL-

SEQ

Segments 1+4 / 2+5 / 3+6 flash sequentially while in every

step the currently active segments keep strobing for 4

Flashes before the the next segments take over. The flash

color cycles through P/T/L

4. SPEED button

By consecutively pressing this key on the main units itself, or by using the SPEED up/down keys on the

remote control, it allows the sequential choice of various speed settings, depending on which MODE the

unit operates in:

In CHASE mode: 1Hz / 2Hz / 4Hz fixed / S2L (with LED indicator)

In FADE mode: speed 0.25Hz fixed/ 0.5Hz fixed / 1Hz / 2Hz fixed

In MOOD mode: speed 0.05Hz fixed / 0.25Hz fixed/ 0.5Hz fixed / 1Hz fixed

In SCENE mode: no speed choice (this button disabled)

In FLASH (STROBE) mode: the strobe speed can bet set in 4 levels.

Note: the chosen speed setting will be stored for every mode, so once returning to the mode, the

previously chose speed will be recalled.

5. S2L (SOUND TO LIGHT) indicator

In chase mode you can use the SPEED-button select different speeds or you can choose to run the

patterns to the rhythm of the music, in this last mode the SOUND TO LIGHT indicator is lit.

6. ON/OFF indicator

Indicates if the LED Marvel is connected to the mains or not.

7. BASE

Used to mount the LED Marvel in many different ways: see the chapter “How to install” for more

information.

8. DMX in/out connectors

You can use the LED Marvel standalone, in master/slave or you can control it using an external DMX-

controller. Please check the chapter “How to connect” for more information.

9. Power adapter in/out

Used to connect the power adapter, you can connect 1 more LED Marvel on the same power adapter.

However the included power adapter does not support this. In short we suggest NOT using the power

adapter output.

10.Microphone

The internal microphone picks up the music so the chases can run to the rhythm of the music.

11.STANDBY (ON/OFF) button

Only available on the remote: sets the output in blackout mode (off). This has the same effect as setting

the level (button 1)

ENGLISH USER MANUAL

JB SYSTEMS®6/44 LED MARVEL

HOW TO INSTALL

The LED Marvel can be mounted in many different ways, you can choose one of these methods:

Table-Top operation: Mostly for “party” use!

Mount the included tripod to the bottom thread insert of the main unit.

Place the unit in a secure position where it can neither be touched by anyone or

could possibly become an objective for anyone to stumble.

If necessary or possible, fix the tripod with three screws (not included) to the

supporting surface.

Make sure the location and position secures safe distance from a spectator’s

direct eyesight.

For proper sound-to-light operation, leave the rear of the unit unobstructed.

Choose an angle that provides safe standing so that the unit cannot accidently flip

over. Make sure the two longer tripod legs direct to the back of the unit.

Connect the power supply and place the power supply in a location where nobody

can accidently stumble over the power supply or the cable.

Make sure to comply with cooling requirements of the used power supply if any.

Wall-mounted operation: Mostly used to color a wall while being mounted on that wall, see drawings A & B.

Mount the included tripod to the rear thread insert of the main unit.

Place the unit in a secure position where it can neither be touched by

anyone or could possibly become an objective for anyone to stumble

or bang his/her head on it.

Fix the tripod with three screws (not included) to the supporting

surface. Make sure the supporting surface can safely carry the weight

of the unit, which can be assumed when the surface can carry 10

times the unit’s weight as a point load.

Make sure the location and position secures safe distance from a

spectator’s direct eyesight.

For proper sound-to-light operation, leave the rear of the unit

unobstructed.

Connect the power supply and place the power supply in a location

where nobody can accidently stumble over the power supply or the

cable.

Make sure to comply with cooling requirements of the used power

supply if any.

Floor-mounted operation: Mostly used to color a wall while standing on the floor or hanging on the ceiling,

see drawings C & D.

Mount the included tripod to the rear thread insert of the

main unit.

Place the unit in a secure position where it can neither

be touched by anyone or could possibly become an

objective for anyone to stumble.

If necessary or possible, fix the tripod with three screws

(not included) to the supporting surface.

Make sure the location and position secures safe

distance from a spectator’s direct eyesight.

For proper sound-to-light operation, leave the rear of the

unit unobstructed.

Choose an angle that provides safe standing so that the

unit cannot accidently flip over.

Connect the power supply and place the power supply in

a location where nobody can accidently stumble over

the power supply or the cable.

Make sure to comply with cooling requirements of the used power supply if any.

ENGLISH USER MANUAL

JB SYSTEMS®7/44 LED MARVEL

HOW TO CONNECT

Standalone use:

Just connect the supplied Power adapter to the DC in (9) connector on the back of the unit.

Before using the IR-remote you should remove the protective plastic sleeve from the battery compartment.

Electrical installation for two or more units in Master/slave or DMX-mode:

The LED Marvel is equipped with a digital control interface connection which allows several units to be

synchronized. Since this digital control interface is based on the DMX512 protocol, it can also be used to

remotely control one or a chain of LED Marvel by means of an external DMX-512 controller. For space

reasons, the control interface however uses a 3.5mm jack connection (instead of the commonly used XLR

type), which means external DMX control requires a custom-made XLR-to-3.5jack cable (not supplied). A

further restriction is that the DMX start address cannot be set on the LED Marvel and is fixed to 001. The

interconnection between two units for synchronization requires a normal 3.5mm stereo jack/jack cable (not

included). The last unit in a chain shall be equipped with a proper 120 Ohm termination resistor equipped

3.5mm stereo jack-plug as shown in below drawing.

Cable connections for Master/slave:

You can connect several units together using an

optional good quality cable with 3.5mm stereo jack on

both sides.

The first unit in the chain will be the master: on this unit

you should press the buttons or use the IR-remote

control.

If you should use long cables the operation of the

slaves could become unreliable. In that case you should

use the 120ohm termination (see previous page) on the

DMX-output of last unit in the line.

Cable connections for DMX-operation:

You can connect several units to the output of any

DMX-controller using an optional good quality

conversion cable with 3.5mm stereo jack on one side

and XLR-connector on the other side. (see previous

page)

Keep in mind that you cannot choose the start address

of the units: the start address is always 001!

If you should use long cables the operation of the

slaves could become unreliable. In that case you should

use the 120ohm termination (see previous page) on the

DMX-output of last unit in the line.

ENGLISH USER MANUAL

JB SYSTEMS®8/44 LED MARVEL

While using an external DMX controller the 21CH DMX-chart can be used:

Channels 1 to 18 can be used to individually control the red, green and blue colors for the 6 panels, see

the chart for the exact information.

Channel 19 is the master dimmer for the 6 panels, see the chart for the exact information.

Channel 20 can be used to recall internal patterns, above DMX-value 247 channels 1 to 19 become active.

Channel 21 is used to set the speed of the internal patterns.

DMX channel

Value Range

Function

CH1

000-255

Panel1 (from top) R level –only active if CH20 >248

CH2

000-255

Panel1 (from top) G level –only active if CH20 >248

CH3

000-255

Panel1 (from top) B level –only active if CH20 >248

CH4

000-255

Panel2 (from top) R level –only active if CH20 >248

CH5

000-255

Panel2 (from top) G level –only active if CH20 >248

CH6

000-255

Panel2 (from top) B level –only active if CH20 >248

CH7

000-255

Panel3 (from top) R level –only active if CH20 >248

CH8

000-255

Panel3 (from top) G level –only active if CH20 >248

CH9

000-255

Panel3 (from top) B level –only active if CH20 >248

CH10

000-255

Panel4 (from top) R level –only active if CH20 >248

CH11

000-255

Panel4 (from top) G level –only active if CH20 >248

CH12

000-255

Panel4 (from top) B level –only active if CH20 >248

CH13

000-255

Panel5 (from top) R level –only active if CH20 >248

CH14

000-255

Panel5 (from top) G level –only active if CH20 >248

CH15

000-255

Panel5 (from top) B level –only active if CH20 >248

CH16

000-255

Panel6 (from top) R level –only active if CH20 >248

CH17

000-255

Panel6 (from top) G level –only active if CH20 >248

CH18

000-255

Panel6 (from top) B level –only active if CH20 >248

CH19

000-255

Master Dimmer CH1-CH18 –only active if CH20 >248

CH20

000-247

Preset Play Mode; value changes preset

248-255

DMX control mode, enables CH1-CH19

CH21

000-255

Preset Play Speed setting –only active if CH20 >247

MAINTENANCE

This device does not need regular maintenance. It is protected by an internal fuse located on the power

supply PCB. If this fuse fails, this usually indicates an internal fault requiring servicing by a qualified

engineer. The fuse shall only be replaced by a fuse of same specification, and the replacement has to be

made by qualified personnel obeying applicable safety rules.

SPECIFICATIONS

Mains Input: 12Vdc / 1A

Power Adapter: AC 90V ~ 250V, 50/60Hz to 12Vdc / 1A

Power consumption: max. 12 Watt

Sound Control: Internal microphone

DMX connections: 3,5mm stereo jack female

DMX channels used: 21 channels

LEDs: 216pcs (72 red + 72 green + 72 blue)

Size: see drawing

Weight: 0,48kg

The information might be modified without prior notice

You can download the latest version of this user manual on our website: www.beglec.com

Table des matières

Langues :

Autres manuels JB Systems Équipement d'éclairage

JB Systems

JB Systems Plano Spot 7TC Manuel utilisateur

JB Systems

JB Systems Sirius Manuel utilisateur

JB Systems

JB Systems CAM-SPOT 30TW Manuel utilisateur

JB Systems

JB Systems iColor 4 Manuel utilisateur

JB Systems

JB Systems LASER BURST III Manuel utilisateur

JB Systems

JB Systems LED Flower Manuel utilisateur

JB Systems

JB Systems Radiant Manuel utilisateur

JB Systems

JB Systems LED DJ-BAR Manuel utilisateur

JB Systems

JB Systems FROG laser Manuel utilisateur

JB Systems

JB Systems STR-300 Manuel utilisateur

JB Systems

JB Systems SOLAR LED Manuel utilisateur

JB Systems

JB Systems LED SPOT Manuel utilisateur

JB Systems

JB Systems LED PINSPOT Manuel utilisateur

JB Systems

JB Systems COB-4BAR Manuel utilisateur

JB Systems

JB Systems INFERNO Manuel utilisateur

JB Systems

JB Systems Water Wave Manuel utilisateur

JB Systems

JB Systems LED Illusion Manuel utilisateur

JB Systems

JB Systems EZ-SPOT15 WW OUTDOOR Manuel utilisateur

JB Systems

JB Systems Andromeda Manuel utilisateur

JB Systems

JB Systems SOOTH SCAN-3 Manuel utilisateur

JB Systems

JB Systems FSP-1000 Manuel utilisateur

JB Systems

JB Systems LED Pulsar Manuel utilisateur

JB Systems

JB Systems LED-UV212 black light Manuel utilisateur

JB Systems

JB Systems DMX512 Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur