J&J Electronics Color Splash Mode d'emploi

Technical Support

Phone: 800.735.4553 ext. 242

For more information about this or other J&J Electronics lighting products,

please visit www.jandjpoolspa.com

Color Splash® LED Pool and Spa

Light Fixture Installation and

Operation Guide

Color Splash® LED POOL AND SPA LIGHT FIXTURES

Available in 120VAC and 12VAC models

Color Splash LED Pool and Spa light xtures offer superior, color illumination for

your pool and spa. This owner’s manual contains important information on installing

and using your new Color Splash LED Pool and Spa light xture. Read and follow all

instructions contained in this manual. Please keep it in a safe place for future reference.

Most states and local codes regulate the construction, installation, and operation of

public pools and spas, and the construction of residential pools and spas. It is important

to comply with these codes, many of which directly regulate the installation and use

of this product. Consult your local building and health codes for more information.

Read and follow all warning notices and instructions contained in this guide before

installing or using the product. Severe injury, death or property damage may result if

the warnings and instructions contained in this manual are not followed.

INSTALLER NOTICE: This Installation and Operation Guide contains important

information about this LED light. Be sure to give this guide to the owner and/or

operator of the LED light for reference regarding the proper installation, operation

and use of this product.

DANGER! FAILURE TO PROPERLY INSTALL AND USE THIS PRODUCT CAN

RESULT IN SERIOUS BODILY INJURY OR DEATH.

WARNING! Comply with all related codes for the installation and

use of this product.

WARNING! Before installing or using this light, read all warnings and

instructions contained in this manual.

pg 1

COLOR SPLASH LED POOL AND SPA LIGHT FIXTURE NICHE COMPATIBILITY

For LPL-F1C ONLY

Pentair®: 78210400, 78210500,

78210600, 78210700, 79206700

Hayward®: SP0604C, SP0600U

Jandy®: PLNICLRG, SSNICLRG1R,

SSNICLRG1S

Jacuzzi®: 94131234

For LPL-S1C ONLY

Pentair®: 78244200, 78244300, 78243200,

78243300, 79206600

Hayward®: SP0606C, SP0610C

Jandy®: PLNICSM, SSNICSM1R, SSNICSM1S

Always disconnect power to the pool and/or spa light at the circuit breaker panel

before attempting to service the light. Failure to do so could result in serious injury

or death due to electrical shock. Installation must be performed in accordance with

all applicable federal, state & local installation codes and ordinances by a licensed or

certied electrician or a qualied pool professional. Improper installation may result

in death or serious injury to pool and/or spa users, installers or others due to electrical

shock. In addition, improper installation may cause property damage. This device is

not intended for use in anything other than in-ground pools/spas.

WARNING! Risk of electrical shock or electrocution

Do not, under any circumstances, splice wire underwater or behind the light niche

during the installation of this light.

Color Splash LED Pool and Spa light xtures are operated through the light’s switch.

No special controller or interface is required. Use a junction box to connect and

operate multiple lights with a single switch.

The following steps detail installation of the Color Splash LED light xture into a new

pool and/or spa construction. Read this section in its entirety prior to beginning any

installation.

WARNING! Important Safety Information for Light Installation

INSTALLER NOTICE: This light’s external cord cannot be replaced and should be

handled with care. Any damage to this external cord necessitates replacing the light.

pg 2

OPERATION FOR 120VAC AND 12VAC

COLOR SPLASH LED POOL AND SPA LIGHT FIXTURES

COLOR SPLASH LED POOL AND SPA LIGHT FIXTURES INSTALLATION

(NEW POOL AND/OR SPA CONSTRUCTION)

INSTALLER NOTICE: A licensed electrician must complete the following steps prior to

installation of this light in a new pool or spa construction.

RATED FIXTURE LIFE: The illumination generated by Color Splash LED light xtures

are based on Light Emitting Diode (LED) technology. The average expected xture

life is rated 50,000 elapsed time hours under normal operating conditions. Pool Water

Temp: 33°F to 97°F (1°C to 36°C), humidity: 0-95% non-condensing.

4" Min.

48" Min.

18" Min. Top of Lens

to Water Level

8" Min. Junction Box

or Low Voltage

Transformer to the

Max. Water Level of Pool

To: GFCI, Circuit Breaker,

and Power Source

Rigid Conduit

#8 AWG Ground

Connector Bonding

Lug is Located at

Rear of Niche

Coil 4 ft. of Power

Cord Around Fixture

Concrete Must Be Cut

Back Around Niche to

Allow for a Compacted

Plaster Seal

1. Feed the xture cord through the conduit to the junction box. Be sure to leave at

least four (4) feet of cord at base of the xture to coil around the light to ensure ease

of servicing once the pool and/or spa is lled; reference Figure 1.

Figure 1.

NEW CONSTRUCTION INSTALLATION STEPS

(ONCE ALL ELECTRICAL REQUIREMENTS ARE MET)

pg 3

ordinances. The electrical system must be installed by a licensed or certied electrician to

meet or exceed those requirements prior to installation of the light. This includes, but is not

limited to, the following National Electrical Code requirements:

• Installation of a ground fault circuit interrupter (GFCI) for line voltage models on the

lighting circuit with an appropriately rated circuit breaker.

• A junction box or low voltage transformer is located at least 8 inches above the maximum

pool water level and at least 48 inches from the pool edge; reference Figure 1.

• Proper electrical bonding of the light xture and all metal items within 5 feet of the pool

• Proper wet niche installation with the top edge of the underwater light’s lens at least

18 inches below the surface of the water in the pool and not more than 20” in Canada;

reference Figure 1.

• Proper electrical wet niche bonding and grounding using the #8 AWG ground connector

at the rear of the niche; reference Figure 1.

WARNING! Conrm that the pool and/or spa meets all current National Electrical

Code (N.E.C.) Article 680-22 requirements and any applicable local codes or

2. At the junction box, cut the cord. Be sure to leave at least six (6) inches of cord for

making connections.

3. Carefully strip the outer cord jacket to expose six (6) inches of the underlying three

insulated wires.

4. Connect these three (3) wires to their corresponding junction box circuit wires and

secure the junction box cover in place.

damage to the light. If the light is operating without being fully submerged in water,

the light’s circuitry will automatically shut down for a cooling period before powering

back on within 10 minutes to prevent damage to the light.

WARNING! Do not operate this light for more than two minutes without

completely submerging it in water. Failure to do so can result in permanent

pg 4

This special pilot screw secures and electrically grounds the xture to the mounting

ring and wet niche. Failure to install the stainless steel pilot screw provided could

create an electrical shock hazard, resulting in death or serious injury to pool users,

installers or others.

5. Using the stainless steel pilot screw provided, install the Color Splash light assembly

into the niche, carefully tightening the pilot screw. (Reference Figure 1)

WARNING! Use only the stainless steel pilot screw provided with this

underwater light.

6. Fill the pool to completely submerge the light prior to operating the light. Do not

operate light out of water, this may cause damage to the light.

7. Make a nal check to conrm proper light operation by switching “on” the main

switch or circuit breaker and the light switch. The light should illuminate when

power is switched “on”. If the light is not operating, go back to Step 1 to recheck each

installation step for proper completion.

pg 5

Installation of this light must be completed by a licensed or certied electrician or a qualied

pool professional in accordance with the National Electrical Code and any applicable local

codes and ordinances. Improper installation may result in death or serious injury to pool

users, installers or others due to electrical shock. In addition, improper installation may

cause property damage.

Always disconnect power to the pool and/or spa light at the circuit breaker panel before

attempting to service the light. Failure to do so could result in serious injury or death due

to electrical shock.

Conrm that the pool or spa meets the current National Electrical Code requirements and

any applicable local codes or ordinances. The electrical system must be installed by a

licensed or certied electrician to meet or exceed those requirements prior to installation

of the light. This includes, but is not limited to, the following National Electrical Code

requirements:

• Installation of a ground fault circuit interrupter (GFCI) for line voltage models on the

lighting circuit with an appropriately rated circuit breaker.

• A junction box or low voltage transformer is located at least 8 inches above the maximum

pool water level and at least 48 inches from the pool edge; reference Figure 1.

• Proper electrical bonding of the light xture and all metal items within 5 feet

of the pool and/or spa.

• Proper wet niche installation with the top edge of the underwater light’s lens at least

18 inches below the surface of the water in the pool and not more than 20” in Canada;

reference Figure 1.

• Proper electrical wet niche bonding and grounding using the #8 AWG ground connector

at the rear of the niche; reference Figure 1.

• The wet niche is properly electrically bonded and grounded via the No. 8 AWG ground

connector located at the rear of the niche; see Figure 1.

COLOR SPLASH LED POOL AND SPA LIGHT FIXTURE INSTALLATION

(EXISTING POOL AND/OR SPA)

Danger - Risk of electrical shock or electrocution!

The following steps detail installation of the Color Splash LED light xture into an

existing pool. Read this section in its entirety prior to beginning any installation.

1. Disconnect the main electrical switch or circuit breaker and the switch which

operates the installed light.

2. Remove the existing light per the original manufacturer’s instructions. Place the

light xture on the deck.

3. Leaving the light xture on the deck, cut the light cord. Be sure to leave at least

six (6) inches of cord in order to connect it to the replacement light cord. Discard the

light xture.

4. Remove the existing cord by pulling it up out of the niche and onto the deck.

Failure to bring the pool and/or spa electrical system up to current code requirements

prior to light installation may create an electrical shock hazard resulting in death or

serious injury to users, installers, or others due to electrical shock, and may also cause

property damage.

WARNING! Pool or spa electrical system must meeting current

code requirements.

4" Min.

48" Min.

18" Min. Top of Lens

to Water Level

8" Min. Junction Box

or Low Voltage

Transformer to the

Max. Water Level of Pool

To: GFCI, Circuit Breaker,

and Power Source

Rigid Conduit

#8 AWG Ground

Connector Bonding

Lug is Located at

Rear of Niche

Coil 4 ft. of Power

Cord Around Fixture

Concrete Must Be Cut

Back Around Niche to

Allow for a Compacted

Plaster Seal

Figure 1.

EXISTING CONSTRUCTION INSTALLATION STEPS

(ONCE ALL ELECTRICAL REQUIREMENTS ARE MET)

pg 6

pg 7

Carefully strip the outer cord jacket to expose six (6) inches of the underlying three

insulated wires.

5. Tape the three existing light wires to the replacement light cord with electrical

insulating tape. Avoid wrapping too much tape around the cords. Otherwise, the

thickness will be too great for the cord to be able to be pulled through the conduit

to the junction box.

6. After removing the junction box cover, disconnect the light xture wires. Then, pull

the cord through the conduit until it is visible in the junction box conduit. Remove the

tape from the cords and separate the wires.

7. Carefully strip the outer cord jacket from the new light cord to expose six (6) inches

of the underlying three insulated wires.

8. Connect these three (3) wires to their corresponding junction box circuit wires and

secure the junction box cover in place.

9. Be sure to leave at least four (4) feet of cord at base of the xture to coil around the

light to ensure ease of servicing; reference Figure 1.

10. Install the Color Splash LED light xture into the niche.

11. Using the stainless steel pilot screw provided, install the Color Splash LED light

xture assembly into the niche, carefully tightening the pilot screw. (Reference Figure

12. Make a nal check to conrm proper light operation by switching “on” the main

switch or circuit breaker and the light switch. The light should illuminate when

power is switched “on”. If the light is not operating, go back to Step 1 to recheck each

installation step for proper completion.

INSTALLER NOTICE: This light’s external cord cannot be replaced and should be

handled with care. Any damage to this external cord necessitates replacing the light.

This special pilot screw secures and electrically grounds the xture to the mounting

ring and wet niche. Failure to install the stainless steel pilot screw provided could

create an electrical shock hazard, resulting in death or serious injury to pool users,

installers or others.

WARNING! Use only the stainless steel screw provided with this underwater

light.

Color Splash LED light xtures are pre-programmed and synchronous with each other

while offering a wide array of lighting effects and options. They offer ve different

light shows to choose from, as well as a Color Lock feature which allows you to “lock”

the light on any solid color.

Color Splash LED light xture features are selectable by turning the existing pool

light switch off and on, known as power cycling. The amount of time the light is off

during the power cycling determines the light feature activated.

1. Parisian Blue

2. Brazilian Red

3. Tahitian Blue

4. Miami Pink

5. Tuscan Orange

6. Arctic White

7. New Zealand Green

1. Northern Lights

2. Super Nova

3. Desert Bloom

4. Patriot Dream

5. Tidal Wash

SOLID COLORS

Your Color Splash LED light xture has seven colors available for you to experience.

Available colors are:

LIGHT SHOWS

Your Color Splash LED light xture has ve light shows from which you can choose.

The rst three light shows display all seven solid colors, while the last two display

selected colors.

SELECT SOLID COLORS

You can select a solid color at anytime by activating the “Color Lock” feature. The Color

Lock feature allows you to stop a light show and “lock” Color Splash on a solid color.

CHANGE LIGHT SHOW

Changing light shows: Turn the pool light power off for 3 seconds and then back on

again. Color Splash LED light xture will advance from the show that is was previously

on, to the next show. Repeat the “change light shows” procedure until the desired light

show is reached.

LIGHTING OPERATION:

CHOOSING COLORS AND LIGHT SHOWS

LIGHTING OPERATION:

HOW TO CHANGE LIGHT SHOW AND SELECT SOLID COLORS

pg 8

pg 9

DEACTIVATION THE COLOR LOCK FEATURE

Turn the pool light power off and then back on again within 2 seconds. Color Splash

will resume light show.

MEMORY MODE

When your Color Splash LED light xtures are turned off for more than 10 seconds,

the solid color or light show on display will be stored. The next time the power is

turned on, the xture will resume displaying that same color or light show.

RESET/SYNCHRONIZE MODE

To activate the reset mode, turn the power off and back on again within 1 second,

three times in a row (off/on, off/on, off/on). All the xtures connected to the switch

will indicate they have been reset and synchronized by ashing red four times. When

you rest the Color Splash LED light xtures they will go back to the Northern Lights

light show.

1. NORTHERN LIGHTS (FACTORY DEFAULT LIGHT SHOW)

Show: Slow cross-fade through all seven solid colors.

Cycle: Two minute color sequence cycle with slow cross-fade between colors. Fixture

will hold on each solid color for 8 seconds before moving to the next.

2. SUPER NOVA

Show: Quick and random ashes through all seven solid colors.

Cycle: Random fast change between solid colors in half second intervals.

NOTE: Your Color Splash LED light xtures are “synchronous”, meaning you can experience

the same light shows in your pool and spa at the same time. However, all of the pool lights

must be on the same electrical circuit for this feature to be operational. Please consult a

qualied electrician to determine your specic pool and spa circuit conguration.

DESCRIPTION OF LIGHT SHOWS AND SOLID COLORS

ACTIVATING THE COLOR LOCK FEATURE

Turn the pool light power off and then back again in 2 seconds. Color Splash will

“lock” on the color it was displaying at the time when you turned it off.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels J&J Electronics Luminaire

J&J Electronics

J&J Electronics PureWhite Mode d'emploi

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Lightolier

Lightolier LP200 Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manuel utilisateur

Lightolier

Lightolier Lytespan 83ED17S Manuel utilisateur

Lightolier

Lightolier Calculite CS8226 Manuel utilisateur