Jadever JWE Manuel utilisateur

JWE 0

Table of Contents

1. Introduction………………………………….…………………………………………. 1

2. Precautions…………………………………….……………………………………….. 1

3. Before Using the Product

3-1 Unpacking and Checking…………………………………………………………………..

3-2 Installing Components ………………………………………..……………………………

3-3 Leveling the Scale………………………………………………..…………………………

4. Product Introduction

4-1 Specifications & General Features …………………………………..............................

4-2 Front Panel

4-2-1 Display …….………………………………………………………………………………

4-2-2 Keyboard………………………………………………………………………………….

4-3 Power Supply……………………………………………………………………………….

5. Operation

5-1 Weighing……………………………………………………………………………………..

5-2 Tare ………………………………………………………………………………………….

5-3 Weight Checking……………………………………………………………………………

5-4 Simple Counting……………………………………………………………………………

5-5 Percentage Weighing ………………………………………………………………………

5-6 Accumulation, Accumulation Display and Accumulation Clear…………………………

6. Calibration

6-1 Single Point Calibration ……………………………………………………………………

6-2 Linear Calibration…………………………………………………………………………..

7.Setting Mode& Description of Parameter Values…………………………… 8

Serial Interface

8-1 RS-232 Connector…………………………………………………………………………

8-2 Single Option……………………………………………………………………………….

8-3 RS-232 Output Format…………………………………………………………………….

Troubleshooting and Error Message………………………………………………. 13

JWE 1

1. Introduction

Thank you for deciding to purchase a JWE Weighing scale from Jadever. This goods has the

excellent performance and splendid properties under severe quality management .It is

recommended to read this manual in full before using it for good function application.

2. Precautions

◎Place the scale on a flat and stable surface. See 3-3 Leveling the Scale for details.

◎Verify thatthe inputvoltage and the plug type matches the localAC power supply. See 4-3

Power supply.

◎W arm up the scale for 15minutes before using it the first time.

◎Keep the scale aw ay from EM I noise, strong wind and vibration, which might cause

incorrect reading.

◎Avoid sudden temperature changes (suitable operating temperature is between -5℃~ 40℃.)

◎D isconnectthe pow ersupply w hen cleaning the scale.

◎Do not immerse the scale in water or other liquids.

◎Service should be perform ed by authorized personnelonly.

3. Before Using the Product

3-1 Unpacking and Checking

Open the package and check the instrument for transport damage. Immediately inform your

dealer if you have complaints or if parts are missing. The package should contain:

● Scale body ● User manual

● Stainless steel pan ● Wire (power cord)

3-2 Installing Components

1. Before using the scale, remove the Delivery protection screw (rotate counterclockwise),

which is located underneath the scale. This screw ensures protection of the load cell during

transport.

2. Cover the stainless steel pan on the plastic pan properly.

3-3 Leveling the Scale

To compensate for small irregularities or inclinations at the location, the scale can be leveled.

The scale is equipped with a level indicator at the front panel .Adjust the leveling feet until the

air bubble in the indicator is centered as shown.

Note: The scale should be leveled each time its location is changed.

JWE 2

4. Product Introduction

1) Stainless Steel weighing pan

2) Plastic weighing pan

3) Delivery Protection Screw

4) Power socket

5) On/Off Switch

6) HI-LO-OK Signal Output and Bilateral RS-232 Standard Interface

7) Print Button

8) Two-stage Switch

9) Bubble Level Indicator

4-1 Specifications &General Features

Specifications

Model

JWE-3K

JWE-6K

JWE-15K

JWE-30K

Capacity

3000g

6000g

15kg

30kg

Division(g)

0.1g

0.2g

0.5g

Display

LCD With Backlight、25mm(H)×8mm(W), 6 digits

Unit

kg、lb、lboz、g、pcs、﹪、台斤、港斤、斤

Interface Bi-direction RS-232 (Optional)

Pan size 334mm×245mm Stainless steel

Power AC 110V/220V (AC±10%) or Rechargeable battery （6V/4A）

Operating Temp. -5℃~ 40℃（23℉~ 104℉）

Maximum Humidity 85﹪relative humidity, non-condensing

JWE 3

General Features

‧3kg/0,1g~30kg/1g

‧1/30,000 display resolution

‧Water-resistant durable keypad

‧Auto power off / Auto backlight

‧HI/LO/OK setting can be stored

‧HI/LO/OK alarm function

‧Soft-ware filtering

‧Stainless steel weighing pan is for long-term operation

‧Operated by power supply or rechargeable battery

‧Internal battery charger

‧Clear LCD display with backlight

‧Overweight and delivery protection

‧Option: RS-232 interface

4-2 Front Panel

4-2-1 Display

Low battery indication.

The weight on the weighing pan is greater than the upper limit.

The weight on the weighing pan is between upper and lower limits.

The weight on the weighing pan is smaller than lower limit.

The weight is stable.

Net weight indicator.

When “ZERO” indicator appears, the scale is in zero status.

Units of measure

Charge Lamp Lights to indicate battery recharging (red) or charged (green).

Accumulation Lamp Lights up when accumulation function is enable.

JWE 4

4-2-2 Keyboard

1) M+/MR key Memory /Memory recall

2) MC/SET key Enables weight checking function /clear previous accumulation data

3) MODE key Cycles through kg, g, lb, lb-oz,斤, 台斤, 港斤,pcs and %（Enable 斤、台

斤and 港斤 under the setting mode if needed .）

4) TARE key Tares the weight of the pan / shiftkey, moves to the left.

5) ZERO+ key Cancels tare / zero the scale ((within 2% of max.capacity) / increase values.

4-3 Power supply

Please verify the local AC power source and switch the two-stage switch to the properly

before plugging into the power outlet.

Alternative power supply

1) AC 110V/220V (AC±10%)

2) (6V/4A) Internal Rechargeable Battery

Power Consumption

About 300mW, 80hrs (without backlight)

About 380mW, 65hrs (with backlight)

Low Battery Warning

When “ ” appears in the upper left corner of the display window, the battery power

requires recharging. The charge lamp turns green from red when the recharging is completed

(which takes about 8 hours). Disconnect the scale from power supply when it is fully charged.

Note: Battery is to replaced only by an authorized service dealer .Risk of explosion can occur

if replaced with the wrong type or connected improperly.

5. Operations

5-1 Weighing

Begin with no load on the scale, the display reading zero .Place item(s) to be weighed on the

scale. The display shown is 1000g, gross weight.

→

JWE 5

5-2 Tare

When weighing a sample that must be held in a container, tare stores the container weight

into memory.

Tare

1) Under the weighing mode, place the container on the weighing pan, wait till stable indicator

appears, and press the key TARE

. The container is tared.

→

2) Place the item(s) to be weighed into the container. The weight displayed is the net

weight. .

3) Remove all items from the weighing pan; the screen displays the tare value.

4) To clear tare with an empty pan, Press down the key TARE (after the appearance of

“ZERO”) or key ZERO+.

5-3 Weight Checking

1) Under the weighing mode, press key MC/SET to enable the weight checking function.

2) Begin by pressing the key MODE. The value of upper limit will display first, with the

left-most digit blinking.

3) To change the upper limit, Press key ZERO+to increment the flashing digit and the key

TARE

to shift to the next digit.

4) Advance to the lower limit setting by pressing key MODE with the left-most digit

blinking. .Repeat the procedure above to set the lower limit.

5) When the lower limit has been set, press key MODE to store the settings and begin

weight checking.

6) Press key M+/MR to cancel Weight Checking and return to weighing mode.

JWE 6

5-4 Simple Counting

1) Under the weighing mode, press key MODE to select the unit “PCS”

2) Press key MC/SET to choose the sampling amount (Options are 25, 50 and 100), then

put the simples on the weighing pan.

3) Wait till the appearance of CAL

4) Two seconds later, the sampling action ends up with a beep.

5) Remove the samples, and put the load on, the scale calculates the amount of the load.

6) Remove the load and press key MODE to select the desired weight unit to go back to

weighing mode.

5-5 Percentage weighing

1) Under the weighing mode, press key MODE to select the unit “%”

2) Press key MC/SET to choose the percentage (Options are 25%, 50% and 100%), then

put the simple on the weighing pan,

3) Wait till the appearance of CAL

4) Two seconds later, the sampling action end up with a beep.

5) Remove the sample, and put the load on, the scale calculates the percentage of the load.

6) Remove the load and press key MODE to select the desired weight unit to go back to

weighing mode.

5-6 Accumulation, Accumulation Display & Accumulation Clearing

Accumulation

1) Under the weighing mode, put the item on the weighing pan. Press key M+MR at the

appearance of “”and the Accumulation Lamp Lights up.

2) Remove the item and the display goes back to zero before the next accumulation can

JWE 7

Accumulation Display

Press key M+MR to display total accumulation data (number of weighments & total weight)

and back to weighing mode.

→ →

Accumulation Clearing

To clear accumulation data, press key MC/SET while the total weight is displayed. The

accumulation lamp goes off when the accumulation data is deleted.

6. Calibration

1.For best results, calibrate the scale at regular intervals. Temperature changes, geographic

gravity variations, altitude changes and abuse are few reasons why a scale may need

recalibration.

2.Here we take JWE-3K as an example.

6-1 Single Point Calibration

1）Press and hold key MODE while powering on the scale. The screen displays “CAL”, then

release the keys.

2）Press key TARE

to enter the zero point calibration mode.

3）Press key MODE to select calibration weight value. Options are1/3 of full load, 2/3 of full

load and full load. E.g., options for JWE-3K are 1, 2 and 3(kg).

4）Put the corresponding weights on the weighing pan, then the calibration procedure

starts.

5）The calibration procedure is completed with a beep and“” flashing. Now, remove

all the weights.

6）Press key ZERO+ to return to weighing mode, key MODE to advance to next setting

menu.

6-2 Linear Calibration

1）Press and hold key TARE while powering on the scale. The screen displays ,

then release the keys.

JWE 8

2) Press key MODE to enter the zero point calibration mode.

3) Wait till appears, put weights of 1/3 of full load on the weighing pan and press

down key TARE E.g., for JWE-3K ,1/3 of full load is 1kg.

4) Wait till appears, and then put weights of 2/3 of full load on pan and press down

key TARE E.g., for JWE-3K, 2/3 of full load is 2kg.

5) Wait till appears, then put weight of full load on and press

TARE

E.g., for

JWE-3K, full load is 3kg.

6) The calibration procedure ends up with a symbol of “PASS”.

7) Remove all the weights, and then press key ZERO+ to return to weighing mode.

7. Setting Mode& Description of Parameter Values

Setting Mode

1) Long-press key MODE while powering on the scale to enter setting mode. The screen

displays “CAL”, then release the keys.

2) Press key MODE to circle through setting modes.

3) Press key M+MR to choose function.

4) Press key MC/SET switch on and off the chosen function. Press key ZERO+ to save the

setting and back to the weighing mode. If more settings are needed, press key MODE again.

Description of Parameter Values

1) Calibration See “7. Calibration”

2) Set the active weight unit. The following setting are available:

kg, g, lb, lb-oz,斤, 台斤, 港斤,pcs and % . (Enable); (disable)

3) Set the init weight unit. The following setting are available:

kg, g, lb, lb-oz,斤, 台斤, 港斤,pcs and %. (Enable); (Disable)

JWE 9

4) Set the filtering level in which the stable indication turns on .The higher the

setting, the slower stabilization time. Options are Fil 1,Fil 2,Fil 4 and Fil 8.

5) Set the period of inactivity before the scale automatically turns off. Options are

Aut.NO=non power-off,Aut.5, Aut.10, Aut.30 and Aut.60(minutes).

6) Set the activation mode of backlight. Options are lit.Aut=Auto on with items

greater than 9d placed on the weighing pan, lit.ON = Backlight on and lit.OFF=Backlight off.

7) Set zero display range. Options are Zero.0(one division) , Zero.1(2 divisions),

Zero.2(3 divisions), Zero.3(4 divisions), Zero.4(5 divisions) and Zero.5(6 divisions) .

8) Set RS-232 Serial Transmission Rate. Options are bAu.96(9600), bAu.48(4800)

and bAu.24(2400)

9) Set Print mode .Options are Prt.Pr(manual print), Prt.St(Stable print) and

Prt.Co(Continuous print)

Note: In the continuous print mode, computer will be automatic chosen as the external

device.

10)→Set external Interface. Options are PC, SH, ZEBRA,TP, AX, EZ2-S and

tdp-643.

11) Set Weight checking memory. (Enable); (Disable )

12) Set Weight checking buzzer beep. Options are beep.Un, beep.IN, beep.NO

and beep.LO.

13) Set RTC Function. (Enable); (Disable)

8. Serial Interface

If external interface is needed, please select the proper two-in-one board first, which

integrates RTC (time display), RS-232 and relay (weight checking) functional module onto

one circuit board. Only after this board is adopted, the three functions can be realized.

Autres manuels pour JWE

Table des matières

Autres manuels Jadever Échelle

Jadever

Jadever JCL Manuel utilisateur

Jadever

Jadever JWE-3K Manuel utilisateur

Jadever

Jadever JC Manuel utilisateur

Jadever

Jadever JWI-700W Manuel utilisateur

Jadever

Jadever NWTE Manuel utilisateur

Jadever

Jadever IDS701-CTRUCK Manuel utilisateur

Jadever

Jadever JCAII Manuel utilisateur

Jadever

Jadever JWE Manuel utilisateur

Jadever

Jadever JCL-3K Manuel utilisateur

Jadever

Jadever JWI 700C Manuel utilisateur

Jadever

Jadever JCL Series Manuel utilisateur

Jadever

Jadever JCL Manuel utilisateur

Jadever

Jadever JCAII Manuel utilisateur

Jadever

Jadever LPWN-1530 Manuel utilisateur

Jadever

Jadever 1.5K Manuel utilisateur

Jadever

Jadever JKH Manuel utilisateur

Jadever

Jadever JWE Manuel utilisateur

Jadever

Jadever Jadever SKY Manuel utilisateur

Jadever

Jadever JWI-501 Series Manuel utilisateur

Jadever

Jadever JWL-1.5K Manuel utilisateur

Jadever

Jadever LGCN-3075 Manuel utilisateur

Jadever

Jadever SNUGIII Series Manuel utilisateur

Jadever

Jadever JWA series Manuel utilisateur

Jadever

Jadever JKD 250 Manuel utilisateur

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur